• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.144-146
• /
• 2004

It is known that Global Positioning System(GPS) is the most efficient navigation system because it provides precise position information on the all areas of Earth regardless of metrology. Until now, the size of GPS receivers has become smaller and the performance of receivers has become higher. So receivers provide the position information of not only static system but also dynamic system. Usually, users make similar movement trajectory according to their life pattern and it is possible to build up efficient database by collecting only the repeated users' position. Because position information calculated by the receiver is erroneous about 10-30m within 5% error tolerance, the position information is oscillated even on the same area. In this paper, we propose the system that can estimate whether users are out of trajectory or in dangerous situation by soft-computing method.

• The Journal of Advanced Prosthodontics
• /
• 제15권2호
• /
• pp.55-62
• /
• 2023

PURPOSE. The aim of this study is to evaluate the accuracy of removable partial denture (RPD) frameworks produced using different digital protocols. MATERIALS AND METHODS. 80 frameworks for RPDs were produced using CAD-CAM technology and divided into four groups of twenty (n = 20): Group 1, Titanium frameworks manufactured by digital metal laser sintering (DMLS); Group 2, Co-Cr frameworks manufactured by DMLS; Group 3, Polyamide PA12 castable resin manufactured by multi-jet fusion (MJF); and Group 4, Metal (Co-Cr) casting by using lost-wax technique. After the digital acquisition, eight specific areas were selected in order to measure the Δ-error value at the intaglio surface of RPD. The minimum value required for point sampling density (0.4 mm) was derived from the sensitivity analysis. The obtained Δ-error mean value was used for comparisons: 1. between different manufacturing processes; 2. between different manufacturing techniques in the same area of interest (AOI); and 3. between different AOI of the same group. RESULTS. The Δ-error mean value of each group ranged between -0.002 (Ti) and 0.041 (Co-Cr) mm. The Pearson's Chi-squared test revealed significant differences considering all groups paired two by two, except for group 3 and 4. The multiple comparison test documented a significant difference for each AOI among group 1, 3, and 4. The multiple comparison test showed significant differences among almost all different AOIs of each group. CONCLUSION. All Δ-mean error values of all digital protocols for manufacturing RPD frameworks optimally fit within the clinical tolerance limit of trueness and precision.

• Journal of Electrical Engineering and Technology
• /
• 제5권4호
• /
• pp.552-560
• /
• 2010

This paper presents an application of layered Artificial Neural Network controller to study load frequency control problem in power system. The objective of control scheme guarantees that steady state error of frequencies and inadvertent interchange of tie-lines are maintained in a given tolerance limitation. The proposed controller has been designed for a two-area interconnected power system. Only one artificial neural network controller (ANN), which controls the inputs of each area in the power system together, is considered. In this study, back propagation-through time algorithm is used as neural network learning rule. The performance of the power system is simulated by using conventional integral controller and ANN controller, separately. For the first time comparative study has been carried out between SMES and CES unit, all of the areas are included with SMES and CES unit separately. By comparing the results for both cases, the performance of ANN controller with CES unit is found to be better than conventional controllers with SMES, CES and ANN with SMES.

• Journal of Information Processing Systems
• /
• 제18권1호
• /
• pp.97-114
• /
• 2022

Interest is increasing in electrocardiogram (ECG) signal analysis for embedded devices, creating the need to develop an algorithm suitable for a low-power, low-memory embedded device. Linear approximation of the ECG signal facilitates the detection of fiducial points by expressing the signal as a small number of vertices. However, dynamic programming, a global optimization method used for linear approximation, has the disadvantage of high complexity using memoization. In this paper, the calculation area and memory usage are improved using a linear approximated template. The proposed algorithm reduces the calculation area required for dynamic programming through local optimization around the vertices of the template. In addition, it minimizes the storage space required by expressing the time information using the error from the vertices of the template, which is more compact than the time difference between vertices. When the length of the signal is L, the number of vertices is N, and the margin tolerance is M, the spatial complexity improves from O(NL) to O(NM). In our experiment, the linear approximation processing time was 12.45 times faster, from 18.18 ms to 1.46 ms on average, for each beat. The quality distribution of the percentage root mean square difference confirms that the proposed algorithm is a stable approximation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권4호
• /
• pp.560-566
• /
• 2010

삼천포항은 국가 지정 무역항으로 새로운 항만이 건설되고 있으며 이에 따른 안전의 요구가 증가하고 있다. 이러한 해상안전을 위한 요구사항을 충족하기 위해 다중빔 음향측심기를 이용한 삼천포 남부해역에 대한 수로측량이 실시되었다. 본 연구에서는 수로측량의 주요한 항목인 수심자료를 획득하였으며, 이 자료를 국제수로기구(IHO)에서 2008년 2월에 간행한 특별 간행물의 최소 수로측량 기준과 비교한다. 3단계로 수심자료를 분석한 결과, 좌 우현의 외곽 빔에 대한 제거범위를 산정하여 필터링함으로서 자료처리의 효율성과 자료의 정확도를 높일 수 있었으며, 남쪽해역은 해류 등 외부환경의 영향 큰 해역에서는 0.2m 정도의 오차가 나타났으며, 중앙 부 및 상부에서는 0.2m이내의 오차가 나타났다. 연구해역의 수심자료는 국제수로기구 수로측량 규정에서 특등급의 허용 오차 내에 99%가 포함되고 1등급에는 100%만족하는 것을 확인 하였다. 본 연구를 통해 해상교통안전지원, 연안관리 등 해양활동의 의사결정의 정확성을 높이는데 기여할 것이다.

• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.147-151
• /
• 2005

CAN(Controller Area Network) is a simple and efficient network system for real time control and measurement. As it is not only good at error detection but also strong in electromagnetic interference, CAN has been widely used all over the industries. Basically, CAN needs a master node in charge of sensor data collection, node scheduling for data transmission to a monitoring system and error detection. According to the number of mater nodes, the CAN system is classified into two type of master system. One is a single master system that has only one master node and the other is a multi-master system where any sensor node can become a master node depending on the system's conditions. While it has the advantage of its fault tolerance, the multi-master system will suffer form the overall performance degradation when a defect is found in the master node. It is because all sensor nodes pertaining to a defective master node lose their position. Moreover, it is difficult and expensive to implement. For a single master system, the whole system will be broken down when a problem happens to a single master. In this paper, a dynamic master system is presented that there are several sub-master nodes of which basic functions are those of other sensor nodes at ordinary times but dynamically changed to replace the failing master node. An effective scheduling algorithm is also proposed to choose an appropriate node among sub-master nodes, where each sub-master node has its precedence value. The performance of the dynamic master system is experimented and analyzed.

• 대한공간정보학회지
• /
• 제18권3호
• /
• pp.105-114
• /
• 2010

본 연구에서는 지적좌표체계의 세계좌표체계로의 변환 실험연구를 통하여 위치 및 면적의 변화량과 이로 파생되는 문제점들을 검토 분석하였다. 그리고 이를 기초로 개선점을 모색하여 보고자 하였다. 연구지역의 좌표변환 결과, 모든 필지경계점(총 478점)에 대한 좌표변환의 표준편차가 X=0.0079m, Y=0.0153m로 나타나 매우 양호하게 산출되었다. 면적의 차이량을 분석한 결과, 평균적으로 0.062$m^2$정도의 차이를 보여, 이는 현행 법률에서 규정하고 있는 면적허용오차 이내인 것으로 나타났다. 따라서 연구대상지역에 한정하여 본다면 위치나 면적부분에서 많은 차이를 보이지 않아 세계좌표계로의 전환이 가능한 것으로 나타났다.

• 한국BIM학회 논문집
• /
• 제3권3호
• /
• pp.9-18
• /
• 2013

In case of applying the BIM method in the civil engineering of irregularly shaped structure, BIM method began to be introduced in the current building engineering area compared with the expected effects of the relatively high construction productivity has been recognized. In this paper, I have developed quantity calculation algorithms applying it to earthwork and bridge construction, tunnel construction, retaining wall construction, culvert construction and implemented BIM based 3D-BIM Modeling quantity calculation. Structure work in which errors occurred in range between -6.28% ~ 5.17%. Especially, understanding of the problem and improvement of the existing 2D-CAD based of quantity calculation through rock type quantity calculation error in range of -14.36% ~ 13.07% of earthwork quantity calculation. It's benefit and applicability of BIM method in civil engineering. In addition, routine method for quantity of earthwork has the same error tolerance negligible for that of structure work. But, rock type's quantity calculated as the error appears significantly to the reliability of 2D-based volume calculation shows that the problem could be. Through the estimating quantity of earthwork based 3D-BIM, proposed method has better reliability than routine method. BIM, as well as the design, construction, maintenance levels of information when you consider the benefits of integration, the introduction of BIM design in civil engineering and the possibility of applying for the effectiveness was confirmed. In addition, as the beginning phase of information integration, quantity document automation program has been developed for activation of BIM. And automatically enter the program code number, linkage and manual volume calculation program, quantity document automation programs, such as the development is now underway, and step-by-step procedures and methods are presented.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.93-101
• /
• 2014

This study aims to investigate the effect of heat input of outside SAW weld on low temperature toughness($-20^{\circ}C$) of inside SAW weld for API 5L X70 with sour gas resistance. As increasing heat input of the outside weld, low temperature toughness of the inside weld was decreased. Especially, in spite of the same heat input, the value of low temperature toughness was fluctuated. On the basis of fracture and microstructure analysis, the low temperature toughness is correlated with the fracture area ratio of shear lips and four kinds of fracture sections. These sections were divided with size and shape of dimple correlated with grain boundary ferrite and cleavage correlated acicular and polygonal ferrite in grain. Therefore, it was seen that these sections were two of final solidification area in the inside weld and the outside weld, no reheated zone and reheated zone in the inside weld. In conclusion, it is thought that the difference of low temperature toughness at the same heat input is due to the fact that each of impact test specimens could have the different microstructure, even though the notch was machined under the error tolerance of 1mm. It is because the final solidification area of the inside weld is very narrow.

• 지적과 국토정보
• /
• 제44권2호
• /
• pp.139-153
• /
• 2014

지적공부의 세계측지계 변환은 토지소유자의 재산권 보호와 직접적인 관련이 있기 때문에 좌표변환에 따른 공부상의 경계와 면적변화를 최소화할 수 있도록 해야 한다. 하지만 일반적으로 수학적인 변환식을 이용한 좌표변환은 지적도면의 형상을 변환 전 후에 정확하게 유지하기는 매우 어렵다. 현재 지적재조사 사업의 좌표변환 모델은 Helmert 변환방식에 의한 4개 변수를 이용하고 있으며 이중 축척계수는 동일 필지내에 경계점 간 상대적인 위치의 변화와 면적변동에 가장 민감한 영향을 미친다. 본 연구에서는 경계점 좌표등록지역 지적공부의 세계측지계 좌표변환 시 토지소유권과 관련이 있는 경계점에 대한 오차를 공차 범위 내에 유지시키면서 면적의 변화가 없도록 축척계수를 고정할 수 있도록 Helmert 변환식을 응용한 3변수변환 방법을 제시하였다.