• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.51-55
• /
• 2011

We investigated the etching characteristics of zinc oxide (ZnO) thin films deposited by the atomic layer deposition method. The gases of the inductively coupled plasma chemistry consisted of $Cl_2$, Ar, and $O_2$. The maximum etch rate was 40.3 nm/min at a gas flow ratio of $Cl_2$/Ar=15:5 sccm, radio-frequency power of 600 W, bias power of 200 W, and process pressure of 2 Pa. We also investigated the plasma induced damage in the etched ZnO thin films using X-ray diffraction (XRD), atomic force microscopy and photoluminescence (PL). A highly oriented (100) peak was present in the XRD spectroscopy of the ZnO samples. The full width at half maximum value of the ZnO sample etched using the $O_2/Cl_2$/Ar chemistry was higher than that of the as-deposited sample. The roughness of the ZnO thin films increased from 1.91 nm to 2.45 nm after etching in the $O_2/Cl_2$/Ar plasma chemistry. Also, we obtained a strong band edge emission at 380 nm. The intensities of the peaks in the PL spectra from the samples etched in all of the chemistries were increased. However, there was no deep level emission.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.60-63
• /
• 2011

We investigated the etching characteristics of zinc oxide (ZnO) and the effect of additive gases in a $Cl_2$-based inductively coupled plasma. The inert gases were argon, nitrogen, and helium. The maximum etch rates were 44.3, 39.9, and 37.9 nm/min for $Cl_2$(75%)/Ar(25%), $Cl_2$(50%)/$N_2$(50%), and $Cl_2$(75%)/He(25%) gas mixtures, 600 W radiofrequency power, 150 W bias power, and 2 Pa process pressure. We obtained the maximum etch rate by a combination of chemical reaction and physical bombardment. A volatile compound of Zn-Cl. achieved the chemical reaction on the surface of the ZnO thin films. The physical etching was performed by inert gas ion bombardment that broke the Zn-O bonds. The highly oriented (002) peak was determined on samples, and the (013) peak of $Zn_2SiO_4$ was observed in the ZnO thin film sample based on x-ray diffraction spectroscopy patterns. In addition, the sample of $Cl_2$/He chemistry showed a high full-width at half-maximum value. The root-mean-square roughness of ZnO thin films decreased to 1.33 nm from 5.88 nm at $Cl_2$(50%)/$N_2$(50%) plasma chemistry.

• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.464-469
• /
• 2002

$SrBi_2Nb_2O_9(SBN)$ thin films were grown on Pt/Ti/Si and p-type Si(100) substrates by rf-magnetron co-sputtering method using two ceramic targets, $SrNb_2O_6\; and \;Bi_2O_3$. The structural and electrical characteristics have been investigated to confirm the possibility of the SBN thin films for the applications to destructive and nondestructive read out ferroelectric random access memory(FRAM). For the optimum growth condition X-ray diffraction patterns showed that SBN films had well crystallized Bi-layered perovskite structure after $700^{\circ}C$ heat-treatment in furnace. From this specimen we got remnant polarization $(2P_r)$ of about 6 uC/$\textrm{cm}^2$ and coercive voltage $(V_c)$ of about 1.5 V at an applied voltage of 5 V. The leakage current density was $7.6{\times}10^{-7}$/A/$\textrm{cm}^2$ at an applied voltage of 5V. And for the NDRO-FRAM application, properties of SBN films on Si substrate has been investigated. From transmission electron microscopy (TEM) analysis, we found the furnace treated sample had a native oxide about 2 times thicker than the RTA treated sample and this thick native oxide layer had a bad effect on C-V characteristics of SBN/Si thin film. After $650^{\circ}C$ RTA process, we got the improved memory window of 1.3 V at an applied voltage of 5 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.47-52
• /
• 2002

A processing method is developed for preparing sol-gel derived $Pb(Zr_{1-x}Ti_x)O_3$ (x=0.5) thin films on Pt-Ir($Pt_{80}Ir_{20}$)-alloy substrates. The as-deposited layer was dried on a plate in air at $70^{\circ}C$. And then it was baked at $1500^{\circ}C$, annealed at $450^{\circ}C$ and finally annealed for crystallization at various temperatures ranging from $580^{\circ}C$ to $700^{\circ}C$ for 1hour in a tube furnace. The thickness of the annealed film with three layers was $0.3{\mu}m$. Crystalline properties and surface morphology were examined using X-ray diffractometer (XRD). Electrical properties of the films such as dielectric constant, C-V, leakage current density were measured under different annealing temperature. The PZT thin film which was crystallized at $600^{\circ}C$ for 60minutes showed the best structural and electrical dielectric constant is 577. C-V measurement show that $700^{\circ}C$ sample has window memory volt of 2.5V and good capacitance for bias volts. Leakage current density of every sample show $10^{-8}A/cm^2$ r below and breakdown voltage(Vb) is that 25volts.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.6
• /
• pp.322-328
• /
• 2015

We investigated the diffusion behaviors, electrical properties, microstructures, and composition of In-Ga-Zn-O (IGZO) oxide thin films deposited by radio frequency reactive magnetron sputtering with increasing annealing temperatures. The samples were deposited at room temperature and then annealed at 300, 400, 500, 600 and $700^{\circ}C$ in air ambient for 2 h. According to the results of time-of-flight secondary ion mass spectrometry and X-ray photoelectron spectroscopy, no diffusion of In, Ga, and Zn components were observed at 300, 400, 500, $600^{\circ}C$, but there was a diffusion at $700^{\circ}C$. However, for the sample annealed at $700^{\circ}C$, considerable diffusion occurred. Especially, the concentration of In and Ga components were similar at the IGZO thin film but were decreased near the interface between the IGZO and glass substrate, while the concentration of Zn was decreased at the IGZO thin film and some Zn were partially diffused into the glass substrate. The high-resolution transmission electron microscopy results showed that a phase change at the interface between IGZO film and glass substrate began to occur at $500^{\circ}C$ and an unidentified crystalline phase was observed at the interface between IGZO film and glass substrate due to a rapid change in composition of In, Ga and Zn at $700^{\circ}C$. The best values of electron mobility of $15.5cm^2/V{\cdot}s$ and resistivity of $0.21{\Omega}cm$ were obtained from the sample annealed at $600^{\circ}C$.

• Journal of Convergence for Information Technology
• /
• v.12 no.2
• /
• pp.149-156
• /
• 2022

In this paper, it was attempted to form a titanium (Ti: Titanium) thin film using the atmospheric pressure plasma process technology for the conductor, which is the main component of the optical sensor. The atmospheric plasma equipment was remodeled. A 4-inch Ti target for sputter was etched using CF4 gas, and the by-product was coated on a glass sample. These by-products were formed up to about 2 cm, and could be divided into 15 areas according to color. Surface shape and constituent elements were analyzed using scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS), respectively. Electrical properties using 4-point probe equipment were also measured. If the process is performed by positioning the sample at about 4.5 mm to 5 mm from the target, a uniform Ti thin film will be deposited. However, it was found that the thin film contained a significant amount of fluorine, which greatly affects the electrical properties of the thin film. Therefore, additional experiments and studies should be performed to remove or minimize fluorine during deposition.

• Journal of the Korean Magnetics Society
• /
• v.21 no.1
• /
• pp.10-14
• /
• 2011

We have measured the ferromagnetic resonance (FMR) signal in as deposited and $400^{\circ}C$ annealed CoFeB/MgO thin film to investigate the annealing effect on magnetic anisotropies and FMR linewidth (${\Delta}H_{PP}$). The uniaxial anisotropy field ($H_{K1}$) was only observed in the as deposited sample. Whereas, in the $400^{\circ}C$ annealed sample, the biaxial anisotropy field ($H_{K2}$) was additionally observed in accompany with uniaxial anisotropy field ($H_{K1}$). The appearance of biaxial anisotropy fields was originated from the crystalline growth of bcc CoFeB(001) from the MgO(001) interface and by the B diffusion during thermal annealing. Also, the ${\Delta}H_{PP}$ of $400^{\circ}C$ annealed sample was increased compared with that of as deposited sample, which was due to the broad distribution of the magnetization axis by the biaxial anisotropy.

• Nuclear Engineering and Technology
• /
• v.5 no.3
• /
• pp.202-213
• /
• 1973

In a continuation of the 1st series of these studies, a separation of the components in organic phases obtained from Szilard Chalmer reactions of aromatic chloro derivatives was attempted to clarify the conditions of isolating the main component. Though it was unable to isolate all constituents of organic phases, the main component was well isolated by means of a simple distillation or a thin layer chromatography. It was identified that the main component was a recombined product of the recoiled $^{38}$ Cl atom with the original sample. In cases of solid samples the main component amounted about 80-60% of the radio activity of the organic phase, whereas the main component from liquid samples gave less than 70% of the radio activity of the organic phase. A prolonged irradiation could increase the yield of a main component, but it was, in case of a radiation senintive compound, decreased as the irradiation is extended. The number of aide produets separated from an organic phase of a liquid sample was greater than that of a solid sample, and hence the main component of a solid sample was isolated easier. The overall fields of the labelled main products of 22 kinds of compounds were listed and a procedure of the separation of the main component by a thin layer chromatograply was proposed and evaluated. The feasibility of the present procedure for labelling purpose was also reviewed with respects to the chemical structure of a compound.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.346-349
• /
• 1998

In order to reduce to the defect density in poly-Si/SiO$_2$ thin films, where poly-Si is either undoped or doped by BF$_2$ implantation, the poly-Si/SiO$_2$ samples have been hydrogenated by rf plasmas of low temperature. Before hydrogenation, both $P_b$ centers and E centers were observed in the poly-Si(undoped)/SiO$_2$ and in the poly-Si(doped)/SiO$_2$. After 30 min hydrogenation, the $P_b$ center was reduced by 80 % doped sample and by 76 % in the undoped sample and the E center was not observed. After 90min hydrogenation, however, increases of the $P_b$ centers and regenerations of the E center were observed in the undoped sample as well as in the doped one. Compared with the undoped sample, the increase of $P_b$ center in the doped one was more dominant.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1279-1281
• /
• 1998

The Co-Cr thin films are one of the most suitable candidates for perpendicular magnetic recording media. The facing targets sputtering(FTS) method has a advantage of preparing films over a wide range of working gas pressure on plasma-free substrates. In this study, we investigated the possibility of employing FTS system for depositing Co-Cr films, Co-Cr thin films were deposited with continuously sputter gas pressure ($P_{Ar}$ = 0.1 mTorr) by FTS method at temperature of $40^{\circ}C$. We find that the change of thickness and deposition rate of sputtered Co-Cr thin films affect crystal orientation and magnetic properties. Crystallographic and magnetic properties were evaluated by x-ray diffractometry(XRD) and vibrating sample magnetometer(VSM) respectively. It has been confirmed that the FTS method is very useful for preparing Co-Cr thin film recording media.