• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1237-1241
• /
• 2003

In this paper, we report a novel RF-MEMS packaging technology with lightweight, small size, and short electric path length. To achieve this goal, we used the ultra thin silicon substrate as a packaging substrate. The via holes lot vortical feed-through were fabricated on the thin silicon wafer by wet chemical processing. Then, via holes were filled and micro-bumps were fabricated by electroplating. The packaged RF device has a reflection loss under 22 〔㏈〕 and a insertion loss of -0.04∼-0.08 〔㏈〕. These measurements show that we could package the RF device without loss and interference by using the vertical feed-through. Specially, with the ultra thin silicon wafer we can realize of a device package that has low-cost, lightweight and small size. Also, we can extend a 3-D packaging structure by stacking assembled thin packages.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.2
• /
• pp.61-68
• /
• 2015

Warpage analysis has been performed for top and bottom packages of thin package-on-packages processed with different epoxy molding compounds (EMCs). Warpage deviation was measured for packages molded with the same EMCs and also the warpage deviations of top and bottom substrates themselves were characterized in order to identify the major factor causing the package warpage. For the top and bottom packages processed with thin substrates, the warpage deviation of the substrates was large, which made it difficult to figure out the effect of EMC properties on the package warpage. Top packages, where the molding area of $13mm{\times}13mm$ covered the most of the substrate area ($14mm{\times}14mm$), exhibited similar warpage behavior with changing the temperature. On the other hand, bottom packages, where the molding area was only $8mm{\times}8mm$, exhibited the complex warpage behavior due to simultaneous occurrence of (+) and (-) warpages on the same package. Accordingly, the bottom packages showed dissimilar temperature-warpage behavior even being processed with the same EMCs.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.31-35
• /
• 2013

TSOP(Thin Small Outline Package) is the IC package using lead frame, which is the type of low cost package for white electronics, auto mobile, desktop PC, and so on. Its performance is not excellent compared to BGA or flip-chip CSP, but it has been used mostly because of low price of TSOP package. However, it has been issued in TSOP package that thermal deflection of lead frame occurs frequently during molding process and Au wire between semiconductor die and pad is debonded. It has been required to solve this problem through substituting materials with low CTE and improving structure of lead frame. We focused on developing the lead frame structure having thermal stability, which was carried out by numerical analysis in this study. Thermal deflection of lead frame in TSOP package was simulated with positions of anti-deflection adhesives, which was ranging 198 um~366 um from semiconductor die. It was definitely understood that thermal deflection of TSOP package with anti-deflection adhesives was improved as 30.738 um in the case of inside(198 um), which was compared to that of the conventional TSOP package. This result is caused by that the anti-deflection adhesives is contributed to restrict thermal expansion of lead frame. Therefore, it is expected that the anti-deflection adhesives can be applied to lead frame packages and enhance their thermal deflection without any change of substitutive materials with low CTE.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.71-76
• /
• 2005

This paper compares of mechanical tensile properties of 6 kinds of copper foil. The beam lead made with copper foil. Different from other package type such as plastic package, Chip Size Package has a reliability problem in beam lead rather than solder joint in board level. A new tensile loading system was developed using voice-coil actuator. The new tensile loading system has a load cell with maximum capacity of 20 N and a non-contact position measuring system based on the principle of capacitance micrometry with 0.1nm resolution for displacement measurement. Strain was calculated from the measured displacement using FE analysis. The comparison of mechanical properties helps designer of package to choose copper for ensuring reliability of beam lead in early stage of semiconductor development.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.2
• /
• pp.65-70
• /
• 2014

Warpage of top packages to form thin package-on-packages was measured with progress of their process steps such as PCB substrate itself, chip bonding, and epoxy molding. The $100{\mu}m$-thick PCB substrate exhibited a warpage of $136{\sim}214{\mu}m$. The specimen formed by mounting a $40{\mu}m$-thick Si chip to such a PCB using a die attach film exhibited the warpage of $89{\sim}194{\mu}m$, which was similar to that of the PCB itself. On the other hand, the specimen fabricated by flip chip bonding of a $40{\mu}m$-thick chip to such a PCB possessed the warpage of $-199{\sim}691{\mu}m$, which was significantly different from the warpage of the PCB. After epoxy molding, the specimens processed by die attach bonding and flip chip bonding exhibited warpages of $-79{\sim}202{\mu}m$ and $-117{\sim}159{\mu}m$, respectively.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.61-70
• /
• 1998

The electrical performance of a package is extremely important for high speed digital system operations. CSP(chip scale package) is known to have better electrical performance than the convnetional packages. In this paper, the electrical performance of the BLP(bottom leaded plastic) package, a kind of CSP, has been alayzed by both simulation and real measurement. The electrical perfdormance of a BLP was compared with that of the conventioanl TSOP(thin small outline package). The leadinductanceand lead capacitance were used for the comparison purposes. The new BLP design provides much better electrical performance that TSOP package. It has about 40% favorable parameter values.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2006.02a
• /
• pp.139-151
• /
• 2006

[ $\bullet$ ] 3D is proliferating in all package types $\bullet$ Thin packages challenge all assembly technologies $\bullet$ Package assembly and test are closely coupled and design for testability is imperative to success

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.49-55
• /
• 2016

Nowadays there are magnetic sensors in a wide variety of equipment such as computers, cars, airplanes, medical and industrial instruments. In many of these applications the magnetic sensors offer safe and non-invasive means of detection and are more reliable than other technologies. The electric current in a conductor generates a magnetic field detected by this type of sensor. This work aims to define a package dedicated to an electrical current sensor using a MTJ (Magnetic Tunnel Junction) as a sensing device. Four different proposals of packaging, three variations of the chip on board (CoB) package type and one variation of the thin small outline package (TSOP) were analyzed by COMSOL modeling software by simulating a brad range of current injection. The results obtained from the thermal and magnetic analysis has proven to be very important for package improvements, specially for heat dissipation performance.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.294-298
• /
• 2013

A FeRh alloy is a well-known efficient magnetocaloric material and some experimental and theoretical studies of bulk FeRh have been reported already by several groups. In this study we report first-principles calculations on magnetic properties of different thickness FeRh thin films in order to investigate the possibility to enhance further the magnetocaloric efficiency. We used two methods of a Vienna Ab-initio Simulation Package (VASP) code and SIESTA package. We found that the FeRh thin films have quite different magnetic properties from the bulk when the thickness is thinner than 6-atomic-layers. While bulk FeRh has a G-type antiferromagnetic(AFM) state, thin films which are thinner than 6-atomic-layers have an A-type AFM state or a ferromagnetic (FM) state. We will discuss possibility of magnetic phase transitions of the FeRh thin films in the view point of a magnetocaloric effect. And we found 4-, 5-, 6-layers films with Fe surface and 7-layers film with Rh surface are FM and they have relatively small magnetocrystalline anisotropy (MCA) energy about less than 70 meV. The small MCA energy leads to reduction of the strength of magnetic field in operating a magnetic refrigerator.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.239-242
• /
• 2003

Optical module package is a hermetic metal-ceramic package for carrying optical IC. In case of LD(laser diode) module, window is used for both the path of optical signal and hermetic sealing of package. So, window has the metallization pattern on the surface for brazing process with package wall. In this study, several method were investigated for metallization. Thin film, thick film and mixed method were used for fabrication of metallization pattern. After brazing process, hermeticity and adhesion strength were tested for characterization of metallization pattern.