• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.72-76
• /
• 2015

150-nm-thick In-Zn-Tin-Oxide (IZTO) films were deposited by RF magnetron sputtering after a 10 to 50-nm-thick $SiO_2$ buffer layer was deposited by plasma enhanced chemical vapor deposition (PECVD) on polyethylene terephthalate (PET) substrates. The electrical, structural, and optical properties of the IZTO/$SiO_2$/PET films were analyzed with respect to the thickness of the $SiO_2$ buffer layer. The mechanical properties were outstanding at a $SiO_2$ thickness of 50 nm, with a resistivity of $1.45{\times}10^{-3}{\Omega}-cm$, carrier concentration of $8.84{\times}10^{20}/cm^3$, hall mobility of $4.88cm^2/Vs$, and average IZTO surface roughness of 12.64 nm. Also, the transmittances were higher than 80%, and the structure of the IZTO films were amorphous, regardless of the $SiO_2$ thickness. These results indicate that these films are suitable for use as a transparent conductive oxide for transparency display devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.484-490
• /
• 2017

We investigated the rewritable operation of a non-volatile memory device composed of Al (top)/$TiO_2$/indium-zinc-oxide (IZO)/Al (bottom). The oxygen-deficient IZO layer of the device was spin-coated with 0.1 M indium nitrate hydrate and 0.1 M zinc acetate dehydrate as precursor solutions, and the $TiO_2$ layer was fabricated by atomic layer deposition. The oxygen vacancies IZO layer of an active component annealed at $400^{\circ}C$ using thermal annealing and it was proven to be in oxygen vacancies and oxygen binding environments with OH species and heavy metal ions investigated by X-ray photoelectron spectroscopy. The device, which operates at low voltages (less than 3.5 V), exhibits non-volatile memory behavior consistent with resistive-switching properties and an ON/OFF ratio of approximately $3.6{\times}10^3$ at 2.5 V.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.249-255
• /
• 1990

The conditions for separation and identification of anionic and nonionic surfactants by thin layer chromatography were investigated. Polyoxy alkylene-type nonionic surfactants were identified by the distribution of alkyl chain and alkylene oxide. Various polyoxyethylenated nonyl phenols were easily distinguished by densitometer. Some anionic surfactants were identified by $R_f$ and color, and the mixtures of anionic and nonionic surfactants were separated. Polyoxyethylenated fatty acid was separated into three parts of diester, monoester and polyethylene glycol, respectively, and the mixed ratio was determined by densitomer. All the experiments were carried out in 13-20 minutes, and the length of run was 80mm.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.11
• /
• pp.1659-1663
• /
• 2003

$Al_2O_3$ thin films were grown on H-terminated Si(001) substrates using dimethylaluminum isopropoxide [DMAl: $(CH_3)_2AlOCH(CH_3)_2$], as a new Al precursor, and water by atomic layer deposition (ALD). The selflimiting ALD process by alternate surface reactions of DMAI and $H_2O$ was confirmed from measured thicknesses of the aluminum oxide films as functions of the DMAI pulse time and the number of DMAI-$H_2O$ cycles. Under optimal reaction conditions, a growth rate of ~1.06 ${\AA}$ per ALD cycle was achieved at the substrate temperature of $150\;^{\circ}C$. From a mass spectrometric study of the DMAI-$D_2O$ ALD process, it was determined that the overall binary reaction for the deposition of $Al_2O_3\;[2\;(CH_3)_2AlOCH(CH_3)_2\;+\;3\;H_2O\;{\rightarrow}\;Al_2O_3\;+\;4\;CH_4\;+\;2\;HOCH(CH_3)_2]$can be separated into the following two half-reactions: where the asterisks designate the surface species. Growth of stoichiometric $Al_2O_3$ thin films with carbon incorporation less than 1.5 atomic % was confirmed by depth profiling Auger electron spectroscopy. Atomic force microscopy images show atomically flat and uniform surfaces. X-ray photoelectron spectroscopy and cross-sectional high resolution transmission electron microscopy of an $Al_2O_3$ film indicate that there is no distinguishable interfacial Si oxide layer except that a very thin layer of aluminum silicate may have been formed between the $Al_2O_3$ film and the Si substrate. C-V measurements of an $Al_2O_3$ film showed capacitance values comparable to previously reported values.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.1
• /
• pp.5-9
• /
• 2015

Optical and electrical properties were studied for Antimony doped tin oxide thin films from precursors containing 10, 30, 50, and 70 atom% of Sb deposited on bare sodalime silica, barrier layer coated sodalime silica, and pure silica glass substrates by sol-gel spinning technique. The direct band gaps were found to vary from 3.13~4.12 eV when measured in the hv range of 2.5~5.0 eV, and varied from 4.22~5.08 eV when measured in the range of 4.0~7.0 eV. Indirect band gap values were in the range of 2.35~3.11 eV. Blue shift of band gap with respect to bulk band gap and Moss-Burstein shift were observed. Physical thickness of the films decreased with the increase in % Sb. Resistivity of the films deposited on SLS substrate was in the order of $10^{-2}$ ohm cm. Sheet resistance of the films deposited on barrier layer coated soda lime silica glass substrate was found to be relatively less.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.142.1-142.1
• /
• 2018

This research presents a new field effect transistor (FET) by using liquid crystal gate dielectric with remote gate. The fabrication of thin-film transistors (TFTs) was used Indium tin oxide (ITO) for the source, drain, and gate electrodes, and indium gallium zinc oxide (IGZO) for the active semiconductor layer. 5CB liquid crystal was used for the gate dielectric material, and the remote gate and active layer were covered with the liquid crystal. The output and transfer characteristics of the LC-gated TFTs were investigated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.571-574
• /
• 2009

Metal oxide/metal bilayer structures are explored as contacts with a low injection barrier in organic thin-film transistors (OTFTs) in an effort to realize their true potential for low-cost electronics. OTFTs with a bilayer electrode of $WO_3$ (10nm) and Al shows a saturation mobility as large as 0.97 $cm^2$/Vsec which are comparable to those of Au-based control samples (~0.90 $cm^2$/Vsec). Scaling of contact resistance with respect to the thickness of $WO_3$ layer is also discussed.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.609-611
• /
• 1997

Pt thin films flow sensors were fabricated by using aluminum oxide films as medium layer and their characteristics were investigated after annealing at $600^{\circ}C$ for 60min. Aluminum oxide improved adhesion of Pt thin films to $SiO_2$ layer without any chemical reactions to Pt thin films under high annealing temperatures. Output voltages increased as gas flow rate and gas conductivity increased because heat loss of heater, which was integrated with a sensing resistor in the flow sensor, increased. Output voltage of flow sensor fabricated on membrane structure was 101mV at $O_2$ flow rate of 2000sccm, heating power of 0.8W while flow sensor fabricated on Si substrate without membrane had output voltage of 78mV under the same conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.351-354
• /
• 2013

Thin-film transistors(TFTs) with silicon-zinc-tin-oxide(SiZnSnO, SZTO) channel layer are fabricated by rf sputtering method. Electrical properties were changed by different annealing treatment of dry annealing and wet annealing. This procedure improves electrical property especially, stability of oxide TFT. Improved electrical properties are ascribed to desorption of the negatively charged oxygen species from the surfaces by annealing treatment. The threshold voltage ($V_{th}$) shifted toward positive as increasing Si contents in SZTO system. Because the Si has a lower standard electrode potential (SEP) than that that of Sn, Zn, resulting in the degeneration of the oxygen vacancy ($V_O$). As a result, the Si acts as carrier suppressor and oxygen binder in the SZTO as well as a $V_{th}$ controller, resulting in the enhancement of stability of TFTs.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.609-614
• /
• 2014

We fabricated amorphous zinc tin oxide (ZTO) transparent thin-film transistors (TTFTs). The effects of Al electrode on the mobility and threshold voltage of the ZTO TTFTs were investigated. It was found that the aluminum (Al)-ZTO contact decreased the mobility and increased the threshold voltage. Traps, originating from $AlO_x$, were assumed to be the cause of degradation. An indium tin oxide film was inserted between Al and ZTO as a buffer layer, forming an ohmic contact, which was revealed to improve the performance of ZTO TTFTs.