• Journal of Acupuncture Research
• /
• v.27 no.5
• /
• pp.89-96
• /
• 2010

Objectives : This study is designed to evaluate the diagnostic significances of DITI on the patients of low back pain according to impression, symptoms and medical history. Methods : According to impression, symptoms and medical history, thermal changes of $BL_{23}$, $BL_{26}$, $BL_{40}$, $BL_{57}$, $GB_{31}$ and $BL_{60}$ were compared forty-eight low back pain patients and twenty-three normal group. Results : Surface temperature of $BL_{26}$ in case of L-spine HNP is significantly higher than normal group. Surface temperature of $BL_{26}$ in case of low back pain is significantly higher, $GB_{31}$ of radiating pain is significantly lower than normal group. Surface temperature of $BL_{26}$ in case of acute stage is significantly higher, $GB_{31}$ of chronic stage is significantly lower than normal group. Conclusions : Thermal changes of $BL_{26}$ and $GB_{31}$ on the patients of low back pain compared with normal group, according to impression, symptoms and medical history has significances.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1192-1202
• /
• 1994

Fatigue behavior and life prediction were presented for thermal-mechanical and isothermal low cycle fatigue of 12Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test at 350 to 600.deg. C and isothermal low cycle fatigue test at 600.deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. Cyclic softening behavior was observed regardless of thermal-mechanical and isothermal fatigue tests. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. The difference in fatigue lives was dependent upon the magnitudes of inelastic strain ranges and mean stresses. Increase in inelastic strain range showed a tendency of intergranular cracking and decrease in fatigue life, especially for out-of-phase thermal-mechanical fatigue. Thermal-mechanical fatigue life prediction was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase thermal-mechanical fatigue lives, which was quite improved conservatively by a proposed strain range partitioning method.

• Journal of The Korean Astronomical Society
• /
• v.27 no.1
• /
• pp.81-102
• /
• 1994

We have decomposed the 11-cm radio continuum emission of the W51 complex into thermal and non-thermal components. The distribution of the thermal emission has been determined by analyzing HI, CO, and IRAS $60-{\mu}m$ data. We have found a good correlation between the 11-cm thermal continuum and the 60- 11m emissions, which is used to obtain the thermal and non-thermal 11-cm continuum maps of the W51 complex. Most of the thermal continuum is emanating from the compact H II regions and their low-density ionized envelopes in W51A and W51B. All the H II regions, except G49.1-0.4 in W51B, have associated molecular clumps. The thermal radio continuum fluxes of the compact H II regions are proportional to the CO fluxes of molecular clumps. This is consistent with the previous results that the total mass of stars in an H II region is proportional to the mass of the associated molecular clump. According to our result, there are three non-thermal continuum sources in W51: G49.4-0.4 in W51A, a weak source close to G49.2-0.3 in W51B, and the shell source W51C. The non-thermal flux of G49.5-0.4 at 11-cm is $\~28 Jy$, which is $\~25\%$ of its total 11-cm flux. The radio continuum spectrum between 0.15 and 300 GHz also suggests an excess emission over thermal free-free emission. We show that the excess emission can be described as a non-thermal emission with a spectral index ${\alpha}{\simeq}-1.0 (S_v{\propto}V^a)$ attenuated by thermal free-free absorptions at low-frequencies. The non-thermal source close to G49.2-0.3 is weak $(\~9 Jy)$. The nature of the source is not known and the reality of the non-thermal emission needs to be confirmed. The non~thermal shell source W51C has a 11-cm flux of $\~130Jy$ and a spectral index ${\alpha}{\simeq}-0.26$.

• International Journal of Highway Engineering
• /
• v.14 no.4
• /
• pp.63-72
• /
• 2012

PURPOSES : Hot-mix asphalt(HMA) concretes show a trend of strength increase at low temperature due to binder stiffness increase, but strength decrease below a ceratin low temperature. This is due to the differential thermal contraction(DTC) which is induced by a significant difference in coefficients of thermal contraction between aggregate and asphalt which is coated around the aggregate. This DTC damage is well known to occur in HMA concrete, but is not yet investigated in warm-mix asphalt(WMA) concretes. METHODS : To evaluate DTC damage on WMA in this study, the flexural strength($S_f$) of WMA concretes, which were produced at $30{\sim}40^{\circ}C$ lower temperature, was evaluated in comparison with that of HMA at -5, -15 and $-25^{\circ}C$. RESULTS : Most of WMA and HMA mixtures showed flexural strength increase down to $-15^{\circ}C$ and decrease below $-15^{\circ}C$. this type of strength reduction below $-15^{\circ}C$ can e explained as the effect of differential thermal contraction that is a consequence of the large difference in coefficients of thermal contraction between aggregate and asphalt. the property reduction of WMA is similar the result of previous works dealt with HMA mixtures. CONCLUSIONS : Even though there is some differences by materials used, the WMA concretes showed a significantly lower DTC damage than HMA concrete at low temperature at ${\alpha}$=0.05 level.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.291-296
• /
• 2000

The crack of concrete induced by the heat of hydration is s serious problem, particularly in concrete structures such as bridge piers. thick walls, box type walls, mat-slab of nuclear reactor building, dams of foundations of high rise buildings, etc. As a result of the temperature rise and restriction condition of foundation, the thermal stress which way induce the cracks can occur. Therefore the various techniques of the thermal stress control in massive concrete have been widely used. One of them is prediction of the thermal stress, besides low-heat cement which mitigates the temperature rise, design change which consider steel bar reinforcement, operation control and so on. In this study, firstly it introduce the thermal cracks control technique by employing low-heat cement concrete, thermal stress analysis, Secondly it shows the application of the cracks control technique like the bottom of No.15,16 Underground LNG Tank in Inchon.

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1932-1938
• /
• 2005

Graphite foams consist of a network of interconnected graphite ligaments and are beginning to be applied to thermal management of electronics. The thermal conductivity of the bulk graphite foam is similar to aluminum, but graphite foam has one-fifth the density of aluminum. This combination of high thermal conductivity and low density results in a specific thermal conductivity about five times higher than that of aluminum, allowing heat to rapidly propagate into the foam. This heat is spread out over the very large surface area within the foam, enabling large amounts of energy to be transferred with relatively low temperature difference. For the purpose of graphite foam thermosyphon design in electronics cooling, various effects such as graphite foam geometry, sub-cooling, working fluid effect, and liquid level were investigated in this study. The best thermal performance was achieved with the large graphite foam, working fluid with the lowest boiling point, a liquid level with the exact height of the graphite foam, and at the lowest sub-cooling temperature.

• The Journal of Korea Robotics Society
• /
• v.17 no.3
• /
• pp.314-321
• /
• 2022

Depth information used in SLAM and visual odometry is essential in robotics. Depth information often obtained from sensors or learned by networks. While learning-based methods have gained popularity, they are mostly limited to RGB images. However, the limitation of RGB images occurs in visually derailed environments. Thermal cameras are in the spotlight as a way to solve these problems. Unlike RGB images, thermal images reliably perceive the environment regardless of the illumination variance but show lacking contrast and texture. This low contrast in the thermal image prohibits an algorithm from effectively learning the underlying scene details. To tackle these challenges, we propose multi-channel remapping for contrast. Our method allows a learning-based depth prediction model to have an accurate depth prediction even in low light conditions. We validate the feasibility and show that our multi-channel remapping method outperforms the existing methods both visually and quantitatively over our dataset.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.18 no.2
• /
• pp.131-134
• /
• 2009

The purpose of this study was to establish whether there are differences in the productivity of the same silkworm(Bombyx mori L.) parthenoclones, obtained by two different methods-thermal and combined, as well as to study their genotype structure by several enzyme loci. It was established that all individuals of parthenoclones Joana, Joana(${\downarrow}{\uparrow}$), Pohi and Pohi(${\downarrow}{\uparrow}$), are homozygous by the studied esterase and phosphoglucomutase loci, which substantiated the clones' genetic stability. By comparative analysis of some biological and technological properties, it was found that parthenoclone Pohi(${\downarrow}{\uparrow}$) obtained by low-high temperature activation is characterized by higher values of these properties as compared to parthenoclone Pohi obtained by thermal parthenogenesis. Comparing the two methods of inducing ameiotic parthenogenetic development, we would recommend that parthenoclone Joana is sustained by thermal parthenogenesis, and parthenoclone Pohi-by the combined method (low-high temperature).

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.3
• /
• pp.1-5
• /
• 2007

In this paper, effective thermal conductivities of water-based Al203-nanofluids with low concentration from 0.01 vol. % to 0.3 vol. % are experimentally obtained by transient hot wire method (THWM). The water-based Al203-nanofluids are manufactured by two-step method which is widely used. To examine suspension and dispersion characteristics of the water-based A1203-nanofluids, Zeta potential as well as transmission electron micrograph (TEM) is observed. We confirm the manufactured Al203-nanofluids have good suspension and dispersion. The effective thermal conductivities of the water-based Al203-nanofluids with low concentration are enhanced up to 1.64% compared with that of DI water at $21^{\circ}C$. In addition, experimental results are compared with theoretical results from Jang and Choi model.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.1
• /
• pp.68-75
• /
• 2009

A major disadvantage of thermal nanoimprint lithography(NIL) is the thermal cycle, that is, heating over glass transition temperature and then cooling below it, which requires a significant amount of processing time and limits the throughput. One of the methods to overcome this disadvantage is to make the processing temperature lower Accordingly, it is necessary to determine the effects on the processing parameters for thermal NIL at reduced temperatures and to optimize the parameters. This starts with a clear understanding of polymer material behavior during the NIL process. In this work, the squeezing and filling of thin polymer films into nanocavities during the low temperature thermal NIL have been investigated based upon a two-dimensional viscoelastic finite element analysis in order to understand how the process conditions affect a pattern quality; Pressure and initial polymer resist thickness dependency of cavity filling behaviors has been investigated.