• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.795-801
• /
• 2012

Nanoparticles have received significant attention because of their unusual characteristics including high surface area to volume ratios. Thiol ligand have been used as stabilizers of metal nanoparticles since Brust et al. They reported the preparation method of ligand capped metal nanoparticles by protecting the nanoparticles with a self-assembled monolayer of dodecanethiolate. In this method, volatile organic compounds (VOCs) were used as sovents. This study was carried out to replace these VOCs with room temperature ionic liquids (RTILs). We used two type of ILs to prepare metal nanoparticles. One is a hydrophobic IL, [BMIM][[$PF_6$] (1-Butyl-3-methylimidazolium hexafluorophosphate) purchased from IL maker, C-Tri from Korea and the other one is a hydrophilic one, [BMIM][Cl] (1-Buthy-3-methylimdazolium chloride) sinthesized by us. In the case of preparing Ag and Au nanoparticles using [BMIM][Cl], we didn't use phase transition reagents and ethanol because it has hydrophilic property and preparing Au, Ag nanoparticles using [BMIM][[$PF_6$] the method is as same as Brust et al.'s except using [BMIM][[$PF_6$] instead of organic solvent because it has hydrophobic property. FT-IR and UV-vis, TEM, TGA analysis have been used in an attempt to determine the particle size and verify functional groups. The particle size obtained from TEM was very similar to those obtained by Brust et al. This is a clear example of ligand capped metal nanoparticles prepared using ionic liquids. And the experimental result demonstrated ionic liquids can act as a highly effective medium for the preparation and stabilization of gold and silver metal nanoparticles.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.3
• /
• pp.223-229
• /
• 2013

Polymer Electrolyte Membrane Fuel Cell (PEMFC) is a power generation system to convert chemical energy of fuels and oxidants to electricity directly by electrochemical reactions. As a catalyst support for PEMFCs, carbon black has been generally used due to its large surface area and high electrical conductivity. However, under certain circumstances (start up/shut down, fuel starvation, ice formation etc.), carbon supports are subjected to serve corrosion in the presence of water. Therefore, it would be desirable to switch carbon supports to corrosion-resistive support materials such as metal oxide. $TiO_2$ has been attractive as a support with its stability in fuel cell operation atmosphere, low cost, commercial availability, and the ease to control size and structure. However, low electrical conductivity of $TiO_2$ still inhibits its application to catalyst support for PEMFCs. In this paper, to explore feasibility of $TiO_2$ as a catalyst support for PEMFCs, $TiO_2$ nanofibers were synthesized by electrospinning and calcinated at 600, 700, 800 and $900^{\circ}C$. Effects of calcination temperature on crystal structure and electrical conductivity of electrospun $TiO_2$ nanofibers were examined. Electrical conductivity of $TiO_2$ nanofibers increased significantly with increasing calcination temperature from $600^{\circ}C$ to $700^{\circ}C$ and then increased gradually with increasing the calcination temperature from $700^{\circ}C$ to $900^{\circ}C$. It was revealed that the remarkable increase in electrical conductivity could be attributed to phase transition of $TiO_2$ nanofibers from anatase to rutile at the temperature range from $600^{\circ}C$ to $700^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.342-343
• /
• 2013

AlSb is a promising material for optical devices, particularly for high-frequency and nonlinear-optical applications. And AlSb offers significant potential for devices such as quantum-well lasers, laser diodes, and heterojunction bipolar transistors. In this work we study molecular beam epitaxy (MBE) growth of an unstrained AISb film on a GaAs substrate and identify the real-time monitoring capabilities of in situ spectroscopic ellipsometry (SE). The samples were fabricated on semi-insulating (0 0 1) GaAs substrates using MBE system. A rotating sample stage ensured uniform film growth. The substrate was first heated to $620^{\circ}C$ under As2 to remove surface oxides. A GaAs buffer layer approximately 200 nm- thick was then grown at $580^{\circ}C$. During the temperature changing process from $580^{\circ}C$ to $530^{\circ}C$, As2 flux is maintained with the shutter for Ga being closed and the reflection high-energy electron diffraction (RHEED) pattern remaining at ($2{\times}4$). Upon reaching the preset temperature of $530^{\circ}C$, As shutter was promptly closed with Sb shutter open, resulting in the change of RHEED pattern from ($2{\times}4$) to ($1{\times}3$). This was followed by the growth of AlSb while using a rotating-compensator SE with a charge-coupled-device (CCD) detector to obtain real-time SE spectra from 0.74 to 6.48 eV. Fig. 1 shows the real time measured SE spectra of AlSb on GaAs in growth process. In the Fig. 1 (a), a change of ellipsometric parameter ${\Delta}$ is observed. The ${\Delta}$ is the parameter which contains thickness information of the sample, and it changes in a periodic from 0 to 180o with growth. The significant change of ${\Delta}$ at~0.4 min means that the growth of AlSb on GaAs has been started. Fig. 1b shows the changes of dielectric function with time over the range 0.74~6.48 eV. These changes mean phase transition from pseudodielectric function of GaAs to AlSb at~0.44 min. Fig. 2 shows the observed RHEED patterns in the growth process. The observed RHEED pattern of GaAs is ($2{\times}4$), and the pattern changes into ($1{\times}3$) with starting the growth of AlSb. This means that the RHEED pattern is in agreement with the result of SE measurements. These data show the importance and sensitivity of SE for real-time monitoring for materials growth by MBE. We performed the real-time monitoring of AlSb growth by using SE measurements, and it is good agreement with the results of RHEED pattern. This fact proves the importance and the sensitivity of SE technique for the real-time monitoring of film growth by using ellipsometry. We believe that these results will be useful in a number of contexts including more accurate optical properties for high speed device engineering.

• Journal of The Korean Association For Science Education
• /
• v.30 no.5
• /
• pp.533-543
• /
• 2010

This paper analyzed the improvement of cognitive level of the students and interactions which occurred in each step of free-topic scientific inquiry to help science teachers understand free-topic scientific inquiry better. Free-topic scientific inquiry is helpful to students with a deep strategic learning goal orientation type or a deep strategic ability goal orientation type in their transition (2B/3A) of cognitive levels. Most students have difficulties in the phase of establishing topics and hypotheses. The result says that the discussion techniques are improved through free-topic scientific inquiry, but the quality of interaction is not easily improved. The deep strategic learning goal orientation type concretizes opinion through interaction in free-topic scientific inquiry. The deep strategic ability goal orientation type are actively involve in the interaction, but they pay no attention to the process because they stick to the result. The surface strategic ability goal orientation type can not deepen a discussion due to high frequency of low level inquiry. However, the frequency of high level inquiry increases through free topic scientific inquiry operation. As a result, the characteristics of free-topic scientific inquiry were discussed and the educational implications of the progress of free-topic scientific inquiry and the organization of grouping were drawn.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.5
• /
• pp.681-688
• /
• 1996

To investigate the effort of drying methods on the physicochemical properties of agar, gel strength, viscosity, melting and setting point, and phase transition by differential scanning calorimetery (DSC) during its heating were determined. In addition the structural differences of agar powder by scanning electron microscope (SEM) was examined. The most shortest onset temperature of gel strength increase was extruding method among any other methods. Viscosity of agar with hot air method, 400.00 cps at $45^{\circ}C$, was markedly increased, but with spraying and extruding ones were little change. The melting and setting point, and the temperature for maximum endothermic and enthalpy for agar with extruding one, $80.01^{\circ}C,\;36.05^{\circ}C\;and\;61.72^{\circ}C,\;0.73\;cal/g$, respectively, were lowest among the drying ones. But in the case of reheating after gelling, there were little change in all methods. Observing the surface structure of agar with SEM, extruding method showed the most unstable with absorptive property.

• Clean Technology
• /
• v.12 no.4
• /
• pp.232-237
• /
• 2006

The zinc-based desulfurization sorbents for a fluidized-bed system were prepared by a spray drying method and the effects of the pH and viscosity of the slurry on the attrition resistance of the prepared sorbents were investigated in this work. In order to improve the attrition resistance, alumina sol was used for an inorganic binder and pH of the slurry was changed for its better dispersion in slurry. The attrition resistance of the prepared sorbents decreased due to the phase transition of alumina sol to gel as the slurry pH increased to its basicity. The optimum pH condition for the good attrition resistance of the sorbents was about 6.0 in this study. It was confirmed that the attrition property of the sorbents were varied with the viscosity of the slurry. The attrition resistance of the sorbents prepared by the spray drying method increased as their bulk density increased, while it decreased as the surface area and porosity of the sorbents. The optimum viscosity for the high attrition was in the range 400-500 cP.

• Clean Technology
• /
• v.19 no.4
• /
• pp.481-486
• /
• 2013

Alkali-surfactant-polymer (ASP) solution was manufactured by using the domestic surfactants for enhanced oil recovery. Domestic surfactants such as linear alkylbenzene sulfonic acid (LAS) and dioctyl sulfosiuccinate (DOSS) were used. This surfactants were purchased from AK chemtech Co., Ltd. (Korea). LAS and DOSS were blended and the ratio of LAS to DOSS are 1:1 and 2:1. Decane was used as a model compound of the crude oil. Surfactant solution and decane were blended to analyze microemulsion. Brine-oil-surfactant are mixed at varying concentration of brine from 0.8 to 3.6 wt.%. Increasing salinity causes the phase transition of microemulsion from water to middle to oil. Also, by measuring the surface tension and interfacial tension using pendent drop tensiometer and Huh's equation optimal ratio of the ASP solution was determined.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.5
• /
• pp.216-221
• /
• 2006

An investigation of the influence of $WO_3$ and $V_2O_5$ catalysts on the microstructure, phase formation and selective catalytic reduction (SCR) efficiency of the synthesized SCR powders has been carried out. A commercial anatase-$TiO_2$ was used as the catalysts support. For $WO_3(10wt%)/TiO_2$, the W loading to the $TiO_2$ support led to the lower in anatase to rutile transition temperature from $1200^{\circ}C$ of $TiO_2$ support to ${\sim}900^{\circ}C$. The transition temperature was also lowered to below $650^{\circ}C$ in the $V_2O_5$(5 and 10 wt%) added composition. The $WO_3(10wt%)/TiO_2$ SCR powder obtained at $450^{\circ}C$ showed near 100% of $NO_x$ conversion efficiency at $350{\sim}400^{\circ}C$ and for the powder prepared at $650^{\circ}C$ the same efficiency was achieved in wider temperature range $300{\sim}400^{\circ}C$. The highest $NO_x$ conversion efficiency of 100% was obtained in the $V_2O_5(5wt%)/TiO_2$ SCR composition calcined at $650^{\circ}C$ in the relatively wider temperature range $250{\sim}350^{\circ}C$, while the catalytic efficiency considerably decreased for the $V_2O_5(10wt%)/TiO_2$. The lowered conversion efficiency of $NO_x$ observed in the $V_2O_5(10wt%)/TiO_2$ composition calcined at $650^{\circ}C$ was considered to be correlated with the lowered surface area resulting from the increased crystallite growth by highly reactive vanadium loading.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.556-561
• /
• 2001

We prepared a new a SOS(silicon-on-silicide) wafer pair which is consisted of Si(100)/1000$\AA$-NiSi Si (100) layers. SOS can be employed in MEMS(micro- electronic-mechanical system) application due to low resistance of the NiSi layer. A thermally evaporated $1000\AA$-thick Ni/Si wafer and a clean Si wafer were pre-mated in the class 100 clean room, then annealed at $300~900^{\circ}C$ for 15hrs to induce silicidation reaction. SOS wafer pairs were investigated by a IR camera to measure bonded area and probed by a SEM(scanning electron microscope) and TEM(transmission electron microscope) to observe cross-sectional view of Si/NiSi. IR camera observation showed that the annealed SOS wafer pairs have over 52% bonded area in all temperature region except silicidation phase transition temperature. By probing cross-sectional view with SEM of magnification of 30,000, we found that $1000\AA$-thick uniform NiSi layer was formed at the center area of bonded wafers without void defects. However we observed debonded area at the edge area of wafers. Through TEM observation, we found that $10-20\AA$ thick amourphous layer formed between Si surface and NiSix near the counter part of SOS. This layer may be an oxide layer and lead to degradation of bonding. At the edge area of wafers, that amorphous layer was formed even to thickness of $1500\AA$ during annealing. Therefore, to increase bonding area of Si NiSi ∥ Si wafer pairs, we may lessen the amorphous layers.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1164-1170
• /
• 1999

The physicochemical characteristics of ${\beta}-glucan$ isolated from waxy and non-waxy barley were investigated. The hull-less waxy and non-waxy barley containing 6.5% and 5.3% of total ${\beta}-glucan$ respectively, were used as a starting material. The yield and ${\beta}-glucan$ content of crude ${\beta}-glucan$ from waxy barley was 5.54% and 62.9%, respectively, and those were higher than 3.34% and 59.2% from non-waxy barley. The crude ${\beta}-glucan$ purified with selective precipitation and enzymatic treatment to obtain the ${\beta}-glucan$ isolate of high purity (>99%). The total yield of purified ${\beta}-glucan$ from waxy and non-waxy barley was 4.46% and 2.59%, respectively. The surface appearance of the purified ${\beta}-glucan$ by scanning electron microscopy (SEM) showed randomly entangled multi-net structure of ${\beta}-glucan$ microfibrils. The melting temperature of ${\beta}-glucan$ from waxy and non-waxy barley measured by differential scanning calorimetry (DSC) was $184.6^{\circ}C$, and $180.3^{\circ}C$, respectively. DSC endotherm of ${\beta}-glucan$ solution showed 2 peaks near $68^{\circ}C$ and $84^{\circ}C$. Enthalpy of phase transition was higher in non-waxy ${\beta}-glucan$ than waxy ${\beta}-glucan$, and the intrinsic viscosity of ${\beta}-glucan$ solution from waxy barley was higher than that of non-waxy ${\beta}-glucan$. The pasting viscosity of barley starch with the purified ${\beta}-glucan$ determined by Rapid Visco-Analyzer was higher than that of barley starch without ${\beta}-glucan$, and the effect of ${\beta}-glucan$ on increasing the paste viscosity was greater in non-waxy barley starch.