• Journal of the Korean Wood Science and Technology
• /
• 제42권3호
• /
• pp.327-338
• /
• 2014

종자의 산지가 다른 루브라참나무(24년생)를 대상으로 물리 및 역학적 관계를 조사하여 생장속도와 목재의 재질과의 관계를 규명하였다. 생재함수율은 변재보다 심재가 높은 것으로 나타났고, 산지 간에 차이를 나타냈다. 비중의 경우 심재는 생장이 좋을수록 작아지는 경향을 보였고, 변재는 생장이 좋을수록 커지는 관계를 나타냈다. 전수축률은 산지간 차이를 나타냈으며, 생장이 좋을수록 수축률과 T/R율은 높아지는 것으로 나타났다. 압축영계수, 휨강도와 휨영계수 및 충격강도는 산지 간 차이를 보였으며, 생장이 좋을수록 낮아지는 경향을 보였다. 전단강도는 산지 간 차이를 보였으며, 생장이 좋을수록 커지는 경향을 보였다. 경도는 세 단면에서 산지 간 차이를 보였으며, 생장이 좋을수록 커지는 경향을 나타냈다. 5종의 산지가 다른 루브라참나무 중 Bancroft산 종자의 경우가 가장 좋은 수고생장을 보이고, 세 번째의 흉고직경을 나타내며, 압축, 휨, 경도, 전단, 충격강도 모두 우수하여 생장과 재질면을 고려했을 때 현시점에서 가장 우수한 품종으로 판단된다.

• Steel and Composite Structures
• /
• 제29권4호
• /
• pp.527-544
• /
• 2018

The paper presents the study on a change in modal parameters and structural stiffness of cable-stayed Fiberline Bridge made entirely of Glass Fiber Reinforced Polymer (GFRP) composite used for 20 years in the fjord area of Kolding, Denmark. Due to this specific location the bridge structure was subjected to natural aging in harsh environmental conditions. The flexural properties of the pultruded GFRP profiles acquired from the analyzed footbridge in 1997 and 2012 were determined through three-point bending tests. It was found that the Young's modulus increased by approximately 9%. Moreover, the influence of the temperature on the storage and loss modulus of GFRP material acquired from the Fiberline Bridge was studied by the dynamic mechanical analysis. The good thermal stability in potential real temperatures was found. The natural vibration frequencies and mode shapes of the bridge for its original state were evaluated through the application of the Finite Element (FE) method. The initial FE model was created using the real geometrical and material data obtained from both the design data and flexural test results performed in 1997 for the intact composite GFRP material. Full scale experimental investigations of the free-decay response under human jumping for the experimental state were carried out applying accelerometers. Seven natural frequencies, corresponding mode shapes and damping ratios were identified. The numerical and experimental results were compared. Based on the difference in the fundamental natural frequency it was again confirmed that the structural stiffness of the bridge increased by about 9% after 20 years of service life. Data collected from this study were used to validate the assumed FE model. It can be concluded that the updated FE model accurately reproduces the dynamic behavior of the bridge and can be used as a proper baseline model for the long-term monitoring to evaluate the overall structural response under service loads. The obtained results provided a relevant data for the structural health monitoring of all-GFRP bridge.

• 한국정밀공학회지
• /
• 제30권5호
• /
• pp.552-558
• /
• 2013

In recent years the interest on flexible display has been increasing as a future display due to its bendable characteristics. An ITO(indium tin oxide) layer, which is part of a flexible display, can be broken easily while bending because it is made of brittle materials. This brittle property can cause the malfunction of flexible display. To analyze fracture characteristics of ITO layer, bending test was conducted commonly. However, it is not possible to know specific phenomena on bended ITO layer by simple bending test only. Accordingly, in this study, the FE(finite element) model is developed similarly to a real flexible display to analyze stress distribution of flexible display under bending condition, especially on ITO layer. To validate FE model, actual bending test was conducted and the test results were compared with the simulation results by measuring reaction forces during bending. By using the developed model, FE analysis about the effect of design parameter (Thickness & Young's Modulus of BL) on ITO Layer was performed. By explained FE analysis above, this research draws a conclusion of reliable design guide of flexible display, especially on ITO layer.

• 펄프종이기술
• /
• 제30권4호
• /
• pp.42-48
• /
• 1998

The bacterial cellulose(BC) has many unique properties that are potentially and commercially beneficial. In order to enhance inherently inferior physical property of chemithermomechanical pulp(CTMP) sheet, chemical pulp has been used widely. Bacterial cellulose also has an enhanced sheet strength because of its unique physical and morphological features. This study was carried out to inverstigate the effect of BC addition on physical properties of CTMP sheets. The effect of BC addition on its optical properties was also discussed. The apparent density, internal bond strength, Young's modulus, tensile strength and folding endurance of CTMP sheet are increasing with increase of BC contents. This strength increase would be attributed to the increase of relative bonding sites among pulp fibers by addition of BC which has microfibrillar structure with very high specific surface areas. There were not so significant changes in opacity of CTMP sheet upto 20% addition level of BC, while over 40% addition, the opacity gradually decreased and levelled off. Porosity is decreased with addition of BC. This decrease would be attributed to densification of sheet by fine and filamentous structure of BC fibers.

• Transactions on Electrical and Electronic Materials
• /
• 제3권2호
• /
• pp.32-37
• /
• 2002

This paper gives the basic mechanical properties of indium-tin-oxide (ITO) films on polymer substrates which are exposed to externally and thermally induced bending force. By using modified Storney formula including triple layer structure and bulge test measuring the conductive changes of patterned ITO islands as a function of bending curvature, the mechanical stability of ITO films on polymer substrates was intensively investigated. The numerical analyses and experimental results show thermally and externally induced mechanical stresses in the films are responsible for the difference of thermal expansion between the ITO film and the substrate, and leer substrate material and its thickness, respectively. Therefore, a gradually ramped heating process and an organic buffer layer were employed to improve the mechanical stability, and then, the effects of the buffer layer were also quantified in terms of conductivity-strain variations. As a result, it is uncovered that a buffer layer is also a critical factor determining the magnitude of mechanical stress and the layer with the Young's modulus lower than a specific value can contribute to relieving the mechanical stress of the films.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.34-39
• /
• 2008

In this study, CFRP(Carbon Fiber Reinforced Plastics) that has high specific strength and elastic modulus and low thermal strain was used as a material for the lightweight structural member. CFRP is a fiber material as anisotropic material. The anisotropic material is characterized by the change of its mechanical properties according to stacking orientation angle. CFRP orientation angle was oriented in [A/B]s in order to examine the effect of CFRP orientation angle on the characteristics of energy absorption. CFRP is very weak to the impact from the outside. So, when impact is applied to CFRP, its strength is rapidly lowered. The hybrid material was manufactured by combining CFRP to aluminum which is lightweight and widely used for structural members of the automobile. The hybrid member was shaped as a side member that could support the automobile engine and mount and absorb a large amount of impact energy at the front-end in case of automobile collision. The bending test device was manufactured in accordance with ASTM standard, and mounted to UTM for bending test. For comparing bending characteristics of the hybrid member with those of Aluminum and CFRP member, tests were performed for aluminum, CFRP and hybrid member, respectively.

• 한국재료학회지
• /
• 제28권5호
• /
• pp.279-285
• /
• 2018

Graphene is an interesting material because it has remarkable properties, such as high intrinsic carrier mobility, good thermal conductivity, large specific surface area, high transparency, and high Young's modulus values. It is produced by mechanical and chemical exfoliation, chemical vapor deposition (CVD), and epitaxial growth. In particular, large-area and uniform single- and few-layer growth of graphene is possible using transition metals via a thermal CVD process. In this study, we utilize polystyrene and boron oxide, which are a carbon precursor and a doping source, respectively, for synthesis of pristine graphene and boron doped graphene. We confirm the graphene grown by the polystyrene and the boron oxide by the optical microscope and the Raman spectra. Raman spectra of boron doped graphene is shifted to the right compared with pristine graphene and the crystal quality of boron doped graphene is recovered when the synthesis time is 15 min. Sheet resistance decreases from approximately $2000{\Omega}/sq$ to $300{\Omega}/sq$ with an increasing synthesis time for the boron doped graphene.

• 공업화학
• /
• 제29권3호
• /
• pp.318-324
• /
• 2018

본 연구에서는 물리적 활성화법인 수증기 활성화법을 이용하여 PAN (Polyacrylonitrile)계 활성탄소섬유를 제조하였다. 활성화는 온도와 시간을 변수로 하였으며, 활성화 온도(700, 750, $800^{\circ}C$)에 도달하였을 때 200 mL/min의 수증기 유량의 조건으로 PAN 탄소섬유의 활성화를 진행하였다. 제조된 활성탄소섬유의 기공구조를 분석하기 위하여 질소가스의 흡 탈 등온선을 통한 비표면적($S_{BET}$) 측정과 표면분석을 위한 AFM 분석을 실시하였다. 또한 인장시험을 실시하여 활성화 결과 형성된 기공구조가 섬유의 기계적 특성에 미치는 영향을 고찰하였다. 그 결과, 활성화 후 섬유의 비표면적($S_{BET}$)은 $448{\sim}902m^2/g$의 값을 나타냈으며, 인장강도는 58.16~84.92%, 탄성계수는 69.81~83.89%의 감소를 보였다.

• 마이크로전자및패키징학회지
• /
• 제25권1호
• /
• pp.41-45
• /
• 2018

기술의 발전과 전자기기의 소형화와 함께 반도체의 크기는 점점 작아지고 있다. 이와 동시에 반도체 성능의 고도화가 진행되면서 입출력 단자의 밀도는 높아져 패키징의 어려움이 발생하였다. 이러한 문제를 해결하기 위한 방법으로 산업계에서는 팬아웃 웨이퍼 레벨 패키지(FO-WLP)에 주목하고 있다. 또한 FO-WLP는 다른 패키지 방식과 비교해 얇은 두께, 강한 열 저항 등의 장점을 가지고 있다. 하지만 현재 FO-WLP는 생산하는데 몇 가지 어려움이 있는데, 그 중 한가지가 웨이퍼의 휨(Warpage) 현상의 제어이다. 이러한 휨 변형은 서로 다른 재료의 열팽창계수, 탄성계수 등에 의해 발생하고, 이는 칩과 인터커넥트 간의 정렬 불량 등을 야기해 대량생산에 있어 제품의 신뢰성 문제를 발생시킨다. 이러한 휨 현상을 방지하기 위해서는 패키지 재료의 물성과 칩 사이즈 등의 설계 변수의 영향에 대해 이해하는 것이 매우 중요하다. 이번 논문에서는 패키지의 PMC 과정에서 칩의 두께와 EMC의 두께가 휨 현상에 미치는 영향을 유한요소해석을 통해 알아보았다. 그 결과 특정 칩과 EMC가 특정 비율로 구성되어 있을 때 가장 큰 휨 현상이 발생하는 것을 확인하였다.

• 한국지반공학회지:지반
• /
• 제14권4호
• /
• pp.5-16
• /
• 1998

대구지역의 제반은 주로 쇄설성 퇴적암인 혈암으로 구성되어 있다. 이 혈암은 비균질, 비등방성 암석으로 각종 물성치와 역학적 특성이 층리면의 각도($\beta$값)에 따라 매우 다르다. 본 연구에서는 대구지역의 혈암에 대하여 각종 물성, 역학특성 시험을 실시하여 다음과 같은 결과를 얻었다. 비중값은 $\beta$값이 커질수록 감소하지만 간극률, 흡수율은 이와 반대로 증가 하였다. 탄성파 속도는 ($\beta$값이 $90^{\circ}$ 일때가 가장 끈 간을 보이고 탄성계수는$\beta$같이 $30^{\circ}$에서 최대치를 나타내었다. 그리고 강도혹성과 강도정수인 점착력과 마찰각은 모두 $\beta$값이 $60^{\circ}$에서 가장 작은 값을 나타내었다.