• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.114-120
• /
• 2006

This paper compares two types of direct torque controllers for permanent magnet synchronous motors(PMSMs). These controllers both use a single-chip FPGA(Field Programmable Gate Array) but have differing hardware configurations. One of the controllers was constructed by programming a soft-core CPU and hardware logic circuits written in VHDL(Very high speed IC Hardware Description Language), while the other was constructed of only hardware logic circuits. The characteristics of these two controllers were compared in this paper. The results show the controller constructed of only hardware logic circuits was able to shorten the control period and it was able to suppress the low torque ripple.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.202-209
• /
• 2003

We succeeded to build a cost effective assistance robotic arm with a compact and lightweight body. The robotic arm has three joints, and the tip of robotic arm to install tools consists of a closed link mechanism, which consisted of two actuators and several links. The robotic arm has been made possible by the use of actuators typically used in radio control devices. The controller of the robotic arm consists of a single chip PIC only. The robotic arm has a friendly user interface, as the operators are aged and disabled in most cases. The operator can manipulate the robotic arm by voice commands or by pressing a push button. The robotic arm has been successfully prototyped and tested on an elderly patient to assist with eating. The results of field test were satisfactory.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.73-76
• /
• 2010

A two-facet approach was used to investigate the parametric performance of functional high-speed DDR3 (Double Data Rate) DRAM (Dynamic Random Access Memory) die placed in different types of BGA (Ball Grid Array) packages: wire-bonded BGA (FBGA, Fine Ball Grid Array), flip-chip (FCBGA) and lead-bonded $microBGA^{(R)}$. In the first section, packaged live DDR3 die were tested using automatic test equipment using high-resolution shmoo plots. It was found that the best timing and voltage margin was obtained using the lead-bonded microBGA, followed by the wire-bonded FBGA with the FCBGA exhibiting the worst performance of the three types tested. In particular the flip-chip packaged devices exhibited reduced operating voltage margin. In the second part of this work a test system was designed and constructed to mimic the electrical environment of the data bus in a PC's CPU-Memory subsystem that used a single DIMM (Dual In Line Memory Module) socket in point-to-point and point-to-two-point configurations. The emulation system was used to examine signal integrity for system-level operation at speeds in excess of 6 Gb/pin/sec in order to assess the frequency extensibility of the signal-carrying path of the microBGA considered for future high-speed DRAM packaging. The analyzed signal path was driven from either end of the data bus by a GaAs laser driver capable of operation beyond 10 GHz. Eye diagrams were measured using a high speed sampling oscilloscope with a pulse generator providing a pseudo-random bit sequence stimulus for the laser drivers. The memory controller was emulated using a circuit implemented on a BGA interposer employing the laser driver while the active DRAM was modeled using the same type of laser driver mounted to the DIMM module. A custom silicon loading die was designed and fabricated and placed into the microBGA packages that were attached to an instrumented DIMM module. It was found that 6.6 Gb/sec/pin operation appears feasible in both point to point and point to two point configurations when the input capacitance is limited to 2pF.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.7
• /
• pp.1929-1940
• /
• 1999

In this paper a VLSI design for the automatic magnetizing and inspection system has been presented. This is a design of a peripheral controller, which magnetizes CRTs and computer monitors and controls the automatic inspection system. We implemented a programmable peripheral interface(PPI) circuit of the control and protocol module for the magnetizer controller by using a 0.8um CMOS SOG technology of ETRI. Most of the PPI functions have been confirmed. In the conventional method, the propagation/ramp delay model was used to predict the delay of cells, but used to model on only a single cell. Later, a modified "linear delay predict model" was suggested in the LODECAP(LOgic DEsign CAPture) by adding some factors to the prior model. But this has not a full model on the delay chain. In this paper a new " delay predict equation" for the design of the timing control block in PPI system has been suggested. We have described the detail method on a design of delay chain block according to the extracted equation and applied this method to the timing control block design. And we had descriptions on the other blocks of this system.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.9
• /
• pp.114-129
• /
• 1996

This paper describes the whole development phase for the underwater vehicle actuating system with high hydroload torque disturbance. This includes requirement analysis, system modeling, control algorithm design, real time implementation, test and performance evaluations. As for driving control algorithms, fuzzy logic, variable structure and PD(Proportional-Differential) algorithm were designed and implemented on board controller using a single chip microprocessor. Intel 8797. And test and performance evaluation is carried out both single test and wystem integration test. We could confirm the basic performance of actuating system through the single test and gereral developing work of any actuating systems was finished with a single performance test of actuating system without system integration test. But, we suggested that system integration test be needed. System integration test is carried out using G/C HILS(Guidance and Control Hardware-In-the -Loop Simulation) which is constituted flight motion simulator, load simulator, real time host computer and the related subsystems such as inertial navigation system, power supply system and Guidance and Control Computer etc.. The most important practical contribution of this paper is that full system characteristics such as minimal control effort, enhancement of guidance and autopilot performance by the actuating system using G/C HILS technique are investigated. Through full running G/C HILS, in spite of the passing to single tests, some control algorithm resulted in failure as to stability of full system and system time frame.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.251-258
• /
• 2012

Recently, NAND Flash memory structure is evolving from SDR (Single Data Rate) to high speed DDR(Double Data Rate) to fulfill the high performance requirement of SSD and SSS. Accordingly, the proper ways of transferring data that latches valid data stably and minimizing data skew between pins by using PHY(Physical layer) circuit techniques have became new issues. Also, rapid growth of speed in NAND flash increases the operating frequency and power consumption of NAND flash controller. Internal voltage variation margin of NAND flash controller will be narrowed through the smaller geometry and lower internal operating voltage below 1.5V. Therefore, the increase of power budge deviation limits the normal operation range of internal circuit. Affection of OCV(On Chip Variation) deteriorates the voltage variation problem and thus causes internal logic errors. In this case, it is too hard to debug, because it is not functional faults. In this paper, we propose new architecture that maintains the valid timing window in cost effective way under sudden power fluctuation cases. Simulation results show that the proposed technique minimizes the data skew by 379% with reduced area by 20% compared to using PHY circuits.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.188-198
• /
• 2010

Recently, as the demand of the environmental-friendly energy storage system such as an electric double-layer condenser increases, that of the bidirectional charger/discharger for the systems also increases. However, when charging/discharging mode-change occurs, the charger/discharger employing a bi-directional DC-DC converter with a commercialized analog controller has a complex circuit scheme, and a poor transient response. On the other hand, if a single digital controller is used for the bi-directional mode, the system performances can be improved by application of an advanced power-processing algorithm. In the paper, an environmental-friendly power storage systems including an Electric Double Layer Capacitor(EDLC) banks were developed with a bi-directional buck-boost converter and a digital signal processor (TMS320F28335). A simulation test-bed was realized and tested by MATLAB Simulink, and the hardware experiment was performed which shows that the dynamic response was improved such as the simulation results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.397-400
• /
• 2009

This paper describes ASIC design of Multimedia application SoC platform based RISC processor with BTB(Branch Target Buffer). For performance enhancement of platform, we use a simple branch prediction scheme, BTB structure, that stores a target address for branch instruction to remove pipeline harzard. Also, the platform includes a number of peripheral such as VGA controller, AC97 controller, UART controller, SRAM interface and Debug interface. The platform is designed and verified on a Xilinx VERTEX-4 FPGA using a number of test programs for functional tests and timing constraints. Finally, the platform is implemented into a single ASIC chip which can be operated at 100MHz clock frequency using the Chartered 0.18um process. As a result of performance estimation, the proposed platform shows about 5~9% performance improvement in comparison with the previous SoC Platform.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.2
• /
• pp.85-91
• /
• 1998

This paper describes an study electric injection system for diesel engines. It is needed effective fuel injection which controls the solenoid valve of fuel pump. To solve this, this paper proposes DCC-PWM method which can realize fast reply and low holding current for solenoid valve on/off. For the proposed design method, simulation tools of ACSL are used to analyze the system. And the single-chip microcomputer is used to reduce the size of controller and to improve flexibility. And the systems validity can be verified through the experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.119-127
• /
• 2008

In this paper, the modular line-connected photovoltaic PCS (photovoltaic power conditioning system) is proposed. A step-up DC-DC converter using a active-clamp circuit and a dual series-resonant rectifier is proposed to achieve a high efficiency and a high input-output voltage ratio efficiently. An IncCond (incremental conductance) MPPT (maximum power point tracking) algorithm that improves MPPT characteristic is used. The PV module current is estimated without using a DC current sensor. By control a inverter using a linearized output current controller, a unity power factor is achieved. All algorithms and controllers are implemented on a single-chip microcontroller and the superiority of the proposed DC-DC converter and controllers is proved by experiments.