• Journal of the Korean Recycled Construction Resources Institute
• /
• 제4권3호
• /
• pp.62-68
• /
• 2009

This research examined engineering properties of high performance concrete, when substitution rate of BS increases. A summary of the test result is as follows. The fluidity of unset concrete increases as the substitution rate of BS increases. The amount of air is reduced more or less, but it seems that enough amount of air can be secured by using more air-entraining agent. Setting time is dramatically delayed as the substitution rate of BS increases. The compressive strength of hardening concrete was weaker than OPC before 28 days passes, due to latent hydraulic property of BS. However, after 28 days, it shows same or better property, which is exceptional for the practical uses of hyper strength concrete. Changes in drying shrinkage rate is quite much, because when hydration happens, the amount of free water in concrete increased as W/B gets larger. The amount of drying shrinkage increases as BS substitution rate increases, but every composition shows less than $-500{\times}10^{-6}$, which is relatively fine.

• Restorative Dentistry and Endodontics
• /
• 제33권4호
• /
• pp.341-351
• /
• 2008

This study investigated the effect of intermittent polymerization on the rate of polymerization shrinkage and cuspal deflection in composite resins. The linear polymerization shrinkage of each composite was measured using the custom-made linometer along with the light shutter specially devised to block the light at the previously determined interval. Samples were divided into 4 groups by light curing method; Group 1) continuous light (60s with light on); Group 2) intermittent light (cycles of 3s with 2s light on & 1s with light off for 90s): Group 3) intermittent light (cycles of 2s with 1s light on & 1s with light off for 120s); Group 4) intermittent light (cycles of 3s with 1s light on & 2s with light off for 180s). The amount of linear polymerization shrinkage was measured and its maximum rate (Rmax) and peak time (PT) in the first 15 seconds were calculated. For the measurement of cuspal deflection of teeth, MOD cavities were prepared in 10 extracted maxillary premolars. Reduction in the intercuspal distance was measured by the custom-made cuspal deflection measuring machine. ANOVA analysis was used for the comparison of the light curing groups and t-test was used to determine significant difference between the composite resins. Pyramid showed the greater amount of polymerization shrinkage than Heliomolar (p < 0.05). There was no significant difference in the linear polymerization shrinkage among the groups. The Rmax was group 4 < 3, 2 < 1 in Heliomolar and group 3 < 4 < 2, 1 in Pyramid (p < 0.05). Pyramid demonstrated greater cuspal deflection than Heliomolar. The cuspal deflection in Heliomolar was group 4 < 3 < 2, 1 and group 4, 3 < 2, 1 in Pyramid (p < 0.05). It was concluded that the reduced rate of polymerization shrinkage by intermittent polymerization can help to decrease the cuspal deflection.

• Journal of the Korean Ceramic Society
• /
• 제14권2호
• /
• pp.73-77
• /
• 1977

The surface diffusion coefficients for nickel, nickel oxide, cuppric oxide, cobalt oxide, alumina and ferric oxide have been determined at various temperatures using the sintering technique. This investigation is based on the model accounting for the sum of the contribution of volume and surface diffusion to the overall shrinkage rate during the initial stage of sintering. Simultaneous measurements of shrinkages and shrinkage rates of the materials compacts were conducted for various annealing times, the results of which were then correlated to the diffusion coefficient.

• Magazine of the Korean Society of Agricultural Engineers
• /
• 제18권4호
• /
• pp.4226-4231
• /
• 1976

The objective of this study is to investigate the characteristics of the concrete mixture and the plastic shrinkage of concrete exposed to a rapid evaporation immediately after placement, and to measure the shringkage rate according to the cement-mixture. Drying of concrete was conducted under a controlled chamber in which the temperature was 36${\pm}$2$^{\circ}C$, the relative humidity 45${\pm}$2%, and the wind velocity 4${\pm}$1m/sec. All of the concrete mo1ds were made to have good workability as 6${\pm}$0.5cm in slump. The results obtained are as follows; 1) The evaporation rate was 3.36kg/$\textrm{km}^2$, 2.98kg/$\textrm{km}^2$ and 2.91kg/$\textrm{km}^2$ respectively for each concretemixtures 365kg, 335kg and 317kg after 5 hour exposure, and the evaporation was measured at all 55∼57% after 2 hours and additional in 10% on after 5 hours exposure. 2) The weight of the concrete were was reduced to 3.0%, 2.6% and 2.4% respectively for each of them. 3) The shrinkage of concrete was 0.87 mm/m, 0.56mm/m and 0.31 mm/m after 5 hour exposure, and the shringkage of concrete was measured at 84%, 59% and 45% after 2 hours and it in 1∼5% after 5 hour exposure and then stopped. 4) A recommendation for good concrete is that the evaporation should be minimized during 2 hours after placement of concrete, if possible.

• Journal of Fashion Business
• /
• 제19권2호
• /
• pp.23-35
• /
• 2015

In this study, the effect of shrink-resist treatment agent on the wool finishing, specifically anti-felting of wool product was studied. We aimed at providing preliminary data leading to the diversification of high-value added fashionable wool product. Two type of wool fabrics, dense and sheer, were employed. The fabric specimens were treated with solutions of shrink-resist treatment agent with wet pick-up rate 110%, 130%, and 150%, respectively, by using a padding mangle. The solution treated fabric specimens were then dried at room temperature first, at $90^{\circ}C$ for 15 minutes in a drying oven, and finally cured at $130^{\circ}C$ for 3 minutes. Cured wool fabric specimens were then subjected to a felting process. The physical and mechanical properties, including shrinkage rate along warp/filling direction, thickness at specified measurement pressure, drape stiffness, and air-permeability, were analyzed. After felting process, the shrinkage rates of wool fabric specimens, treated with shrink-resist treatment agent, were lower than those of control wool fabric specimens. The stiffness values of wool fabric specimens measured by using Flexometer were increased.

• Journal of the Korea Institute of Building Construction
• /
• 제20권5호
• /
• pp.391-397
• /
• 2020

This study is to compare and analyze the strength, drying shrinkage and carbonation properties of lightweight aggregate mortar using recycling water as prewetting water and mixing water. The flow, compressive strength, split tensile strength, drying shrinkage and carbonation depth of lightweight aggregate mortar with recycling water were measured. As test results, the mortar flow was similar in all mixes regardless of the recycling water content. The compresseive strength of the RW5 mix with 5% recycling water as prewetting water and mixing water was the highest value, about 53.9 MPa after 28 days. In addition, the tensile strength of lightweight mortar was about 3.4 to 3.8 MPa, indicating 7 to 9% of the compressive strength value regardless of recycling water content. In the case of drying shrinkage, the RW2.5 mix using 2.5% recycling water showed the lowest shrinkage rate as about 0.107% at 56 days. The drying shrinkage of the plain mix without recycling water was relatively higher than the RW2.5 and RW5 mix. The RW5 mix showed lowest carbonation depth compared to other mixes. In this study, the RW5 lightweight aggregate mortar with 5% recycling water exhibits excellent compressive strength and carbonation resistance. Therefore, it is considered that if the recycling water, a by-product of the concrete industry, is properly used as prewetting water and mixing water of lightweight mortar and concrete, it will be possible to increase the recycling rate of the by-product and contribute to improve the property of lightweitht aggregate mortar and concrete.

• Journal of the Korea Concrete Institute
• /
• 제14권4호
• /
• pp.521-529
• /
• 2002

A restraint coefficient for creep and dry shrinkage deformation of concrete in a composite section was derived to calculate the residual stress, and an equation for the loss rate of the pre-compression force was proposed. The derived restraint coefficient was computed by using the transformed section properties for the age-adjusted effective modulus of elasticity. The long-term behavior of complicate composite sections could be analyzed easily with the restraint coefficient. The articles of the current design code was examined for PSC and steel composite sections. The dry shrinkage strains of $150 ~ 200$\times$10^{-6}$ for the computations of the statically indeterminate force and the expansion joint could be under-estimated for less restrained sections such as the reinforced concrete. The dry shrinkage strain of $180$\times$10^{-6}$ for the computation of residual stress in the steel composite section was unreasonably less value. The loss rate of 16.3% of the design code for the PSC composite section in this study was conservative for the long-term deformation of the ACI 205 but could not be used safely for that of the Eurocode 2. For pre-compressed concrete slab in the steel composite section, the loss rate of prestressed force with low strength reinforcement was much larger than that with high strength tendon. The loss rate of concrete pre-compression increased, while that of pre-tension decreased due to the restraint of the steel girder.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.5-11
• /
• 2012

The sink mark on boss parts is generated by the volumetric shrinkage that is caused by both the molding thickness and the boss wall thickness. The volumetric shrinkage is caused by packing pressure and its amount tends to decrease by increasing the packing pressure. The packing pressure can therefore increase the flow rate to a boss part and causes the depth of sink mark to increase. As the molding thickness and the boss wall thickness in the boss part can increase the part volume, these may yield bad solidifying and also extend the molding cycle. In this paper, both the injection molding test and the flow analysis were carried out to investigate the effect of sink mark that was generated in the boss wall thickness of injection molded products. The sink mark could also be caused by thickness ratio of boss part. For a given thickness ratio of boss, several molding process parameters such as packing pressure, packing time and melt temperature, affecting to generation of the sink mark were discussed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.90-91
• /
• 2014

In this study, the effect of very fine sand on drying shrinkage cracking of concrete was experimentally evaluated. As a result of the study, the time-to-cracking of concrete used very fine sand was shorter than plain concrete. Also, the stress rate of concrete used very fine sand was higher than plain concrete. It was due to the increase of water content when very fine sand was used in concrete. In conclusion, the use of very fine sand can lead the increase of water content to meet the target slump and higher potential of cracking of concrete.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.