• Journal of Auto-vehicle Safety Association
• /
• v.13 no.4
• /
• pp.66-72
• /
• 2021

This study was initiated to improve of the defect investigation method using event data recorders (EDR) and suggested a solution through the regulation and system analysis of EDR. The EDR data has been used for various purposes such as the vehicle defect investigation and the traffic accident investigation. However the EDR regulation has not been updated since the implementation in 2012. "Trigger Threshold" can be used to analyze a single accident such as the frontal crash, the side crash, and the rollover. In the case of a complex accident in which a rollover accident and a crash accident occur simultaneously, it is difficult to analyze a complex accident due to current "Trigger Threshold". This study proposed the method of separating the "Trigger Threshold" into a crash accident and a rollover accident so that accidents can be analyzed using the EDR data even when a complex accident occurs. In addition, it proposed the improvement method to quickly use the data of EDR in accident reconstruction software.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.511-518
• /
• 1999

Though not very often, a train accident can cause large number of fatality. As a result, public concern about its safety is increasing nowadays. Tn this paper, the structural crashworthiness of Korean High Speed Train trailer was examined through FE analysis. Crash analyses on energy absorbing part and safety zone were carried out to determine each section force. Rollover analysis was performed to observe the amount of intrusion in the passenger's area in case of rollover accident.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.1
• /
• pp.20-26
• /
• 2018

The fatality of rollover accidents in motor vehicle crashes is high despite their low incidence. Through the investigation of a 12-passenger van rollover accident in which 10 passengers were involved, we intend to analyze the correlation between the severity of the injury and the position of the occupants. We collected accident information from medical records, interviews, photo-images of the damaged van, field surveys, and the results of the Korean New Car Assessment Program (KNCAP). Based on the occupants' position, we classified injury sites and estimated injury severity. Passenger injury severity was evaluated by trauma score calculation. The initiation type of the rollover accident was passenger side 'fall-over' and the Collision Deformation Classification (CDC) code for the damaged van was 00TDZO3. The crash of the van involved 10 passengers, with an average age of $16.3{\pm}4.2years$. Few of the occupants had fastened seat belts at the time of the incident, and there was no airbag installed. One patient sustained severe liver injury and another was diagnosed with a fracture of the right humerus. The most common injuries were at the upper extremities and the neck. The average of Injury Severity Score (ISS) was $4.8{\pm}5.9$, and the average ISS of right-seated, mid-seated and left-seated occupants was $7.5{\pm}9.3$, $1.5{\pm}0.7$, and $3.3{\pm}2.1$ respectively (p>0.05). In the rollover (to-passenger side) accident of occupant unfastened, the average ISS of right-seated occupants (near side) was higher, but there was no statistically significant difference.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.4
• /
• pp.54-59
• /
• 2018

While the advanced trffic environment systems are developed recently, the traffic systems for transportation vulnerable are still under development and their social life are limited as well. In order to the secure their mobility rights, it had been required to set up the particular system for the traffic welfare. One of the significant items is the express bus operation for wheelchair users. Thus, the research of development and operation for express buses with wheelchair users was funded by the Korean government. Before the express bus development for wheelchair users based on the current bus model, this study set up the evaluation method for the bus rollover characteristics to ensure occupant safety using the finite element method. The partial bus model was developed corresponding to the full bus model response under rollover event and the evaluation method based on two model (full bus model and partial bus model) responses is planned to apply the model development of express bus modification for wheelchair users.

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.398-413
• /
• 2016

This work describes the design and development of a new drying system for a rollover carwash machine with the support of numerical tools. The drying system is composed of a pair of stationary vertical dryers and a moveable horizontal dryer that can adjust itself to the contour of a vehicle. After the definition of the dryers' concept, their performance was assessed individually to check their internal flow pattern and to improve their airflow distribution. These issues are expected to provide feedback on redesign and geometric optimization of the dryers. After redesign of the dryers separately, the behaviour of the complete drying system was studied on actual vehicle models, representative of the shortest and tallest dimensions that can be washed with the existing carwash machine sector. The drying efficiency of the whole system was studied by calculation of shear stress distribution on various surfaces of a given vehicle. The results allowed concluding that the overall drying performance of the design system is very good and assure adequate drying on most vehicles surfaces. The results obtained from numerical studies were then validated with experimental measurements and a good agreement was found between the two. The procedure employed in this work can be applied to support the design and analysis of other mechanical drying systems.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.8
• /
• pp.828-834
• /
• 2014

This paper presents a comparison among three types of approaches to an ARC (Active Roll Control) with an AARB(Active Anti-Roll Bar) for a vehicle system. Lateral acceleration and road profile are considered as disturbance. The ARC is designed with an LQ SOF (Linear Quadratic Static Output Feedback) control, $H_{\infty}$ control and SMC (Sliding Mode Control). These approaches are compared in terms of rollover prevention and ride comfort. For comparison, Bode plot analysis based on linear model and frequency response analysis based on CarSim simulation are performed.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.198-204
• /
• 2001

Train crashes involve complex interaction between deformable bodies in multiple collisions. The purpose of this study is to suggest the effective analytical procedure using hybrid model for the crashworthiness of motorized trailer of high speed train. The hybrid approach, with very short modeling times and reduced computation times to extract the global behaviour and to perform a pre-optimization of the considered structure. Firstly, various types of crash events are investigated and the conditions for numerical simulation are defined. In this paper, the structural crashwonhiness of Korean High Speed Train trailer was examined through FE analysis. Crash analyses on energy absorbing part and safety zone were carried out to determine each section force. Rollover analysis was performed to observe the amount of intrusion in the passenger's area in case of rollover accident.

• Journal of the korean Society of Automotive Engineers
• /
• v.31 no.3
• /
• pp.36-46
• /
• 2009

• Journal of Trauma and Injury
• /
• v.27 no.3
• /
• pp.50-56
• /
• 2014

Purpose: Rollover motor vehicle crashes have a higher injury severity and fatality than other motor vehicle crash types. From a left-quarter turn rollover accident of 25-passenger bus, we intend to assess the injury of the occupant and the injury severities according to the occupants' position. Methods: We carried out the 3 steps investigation of occupants' interview, visiting the repair shop and using the police report. We analyzed injuries sustained by occupants, and compared injury severities considering column, row in occupant's position and passenger interaction Results: The rollover involved 14 passengers in the bus who were all old women except a man driver. The most common injury was in the upper extremity, with six occurrences being a left clavicle fracture. Major injuries including hemothorax and pneumothorax were diagnosed at left side of the occupant. In the comparison of injury severity among driver's column (left side), mid column and passengercolumn, ISS of passenger column was the highest ($9.9{\pm}7.4$, $8.8{\pm}5.5$, and $10.3{\pm}4.0$, respectively, p>0.05). The injury severity of multiple occupants by row was higher than that of single occupant (10.8 vs. 3, p<0.05). Conclusion: An occupant must fasten their seat belt to prevent an injury by passenger interaction in the left-quarter turn rollover accident of a bus.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.987-991
• /
• 2005

The Aerial platform Truck is widely used for work in high place with the aerial platform. The most important thing is that worker's safety and worker must be able to work with trustworthiness so it needs to be verified its stiffness, deflection of boom, and dynamic condition concerned with a rollover accident. It should have an analytical exactitude because it is directly linked with the worker safety. In this point, we are trying to develop a proper CAE analysis model concerned with a rollover safety, bending stress and deflection for load. The Aerial platform Truck have a dynamic characteristics by load and moving of boom in the work field, so its static and dynamic strength analysis, structural mechanics are very important. Therefore, we evaluate the safety of each boom to calculating its stress, deflection. A computer simulation program is used widely for doing applying calculation of stiffness and structural mechanics, then finally trying to find a optimum design of the Aerial platform Truck.