• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.86-88
• /
• 1999

We investigated the current limiting characteristics of resistive and inductive SFCLs with $100{\Omega}$ of quench impedance for a line-to-line fault in the 154 kV transmission system. The fault simulation at the phase angles $0^{\circ}$, $45^{\circ}$, and $90^{\circ}$ showed that the resistive SFCL limited the fault current less than 15 kA without any DC component after one half cycle from the instant of the fault. On the other hand, the inductive SFCL suppressed the current below 13 kA, but with $2{\sim}3\;kA$ of DC component which decreased to zero in 6 cycles. We concluded that the inductive SFCL had higher performance in current limiting but the resistive SFCL was better from the view point of DC components.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2155-2157
• /
• 1999

This paper describes a new measurement method of resistive current and the technique of deterioration diagnosis for ZnO element. The consequence of current increasing (resistive current) with time is the eventual attainment of a state of thermal instability that may lead to arrester failure. So, it is very important to measure a leakage current of ZnO arrester installed at on-state. For the high-precision and more reliability, an iron core, which has a very high relative permeability, was used for increasing detection sensitivity, and we also used the personal computer for the data storage and program and analysis. And we have verified the reliability and performance of the sensing device through several laboratory tests.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1535-1537
• /
• 2009

High performance resistive type touch panel was fabricated on flexible polyethylene terephthalate (PET) substrates coated with Al- and Ga-codoped ZnO (AGZO) films. The AGZO films were deposited by roll-to-roll direct current magnetron sputter at room temperature. The AGZO thin films on PET substrates showed high transparency (> 85 % at 550 nm) and low sheet resistance (450 ${\Omega}$/sq.). These values were similar to those of commercial ITO films used for resistive type touch panel.

• ETRI Journal
• /
• v.33 no.5
• /
• pp.818-821
• /
• 2011

A D-band subharmonically-pumped resistive mixer has been designed, processed, and experimentally tested. The circuit is based on a $180^{\circ}$ power divider structure consisting of a Lange coupler followed by a ${\lambda}$/4 transmission line (at local oscillator (LO) frequency). This monolithic microwave integrated circuit (MMIC) has been realized in coplanar waveguide technology by using an InAlAs/InGaAs-based metamorphic high electron mobility transistor process with 100-nm gate length. The MMIC achieves a measured conversion loss between 12.5 dB and 16 dB in the radio frequency bandwidth from 120 GHz to 150 GHz with 4-dBm LO drive and an intermediate frequency of 100 MHz. The input 1-dB compression point and IIP3 were simulated to be 2 dBm and 13 dBm, respectively.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2552-2554
• /
• 2001

This paper presents a front-end electronic circuits for signal detection on multi-gap resistive plate. The input to the circuit is the signal(voltage : -800mv, frequency : 20${\sim}$40MHZ, noise : 50mv, 1GHz) from the multi-gap resistive plate chamber and the output is the 5v pulse signal. The front-end electronic circuit consists of preamplifier, peak-detector, and comparator. Spice simulation show that the circuit has the better response time than the one of the conventional measuring instruments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1306-1313
• /
• 2012

This paper reports the contamination performance of two distribution arresters (new and used ones) tested under three different contaminant conditions - clean fog, ESDD (equivalent salt deposit density) level (A, B, C, and D), and kaolin contamination conditions, and their leakage current, total leakage current, and component of the resistive leakage current were measured in order to diagnose arrester deterioration. The 3rd harmonics was larger than 5th and 7th ones for the arrester under the clean fog, and as the ESDD contamination level was applied, 5th one became relatively larger than 3rd one. Therefore, these results indicated that the resistive leakage current could be used for the diagnosis of the arresters.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.107-110
• /
• 2005

This paper presents the reduction methods of penetrated electromagnetic fields through a narrow slot aperture in a planar conducting screen of infinite extent. When a plane wave is excited to the narrow slot, the aperture electric field is controlled by the resistive sheets loading on the slot. The magnitude of the penetrated electromagnetic fields through a narrow slot is controlled by electric field distributions on the slot aperture. The results show that the magnitude of the penetrated electromagnetic field can be effectively reduced by the resistive sheets on the slot aperture.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.281-283
• /
• 2006

This paper presents the reduction methods of penetrated electromagnetic fields through a narrow slot aperture in a planar conducting screen of infinite extent. When a plane wave is excited to the narrow slot, the aperture electric field is controlled by the resistive sheets loading on the slot. The magnitude of the penetrated electromagnetic fields through a narrow slot is controlled by electric field distributions on the slot aperture. The results show that the magnitude of the penetrated electromagnetic field can be effectively reduced by the resistive sheets on the slot aperture.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.3
• /
• pp.323-338
• /
• 2022

Heat generation and temperature of a battery is usually presented by an equation of current. This means that we need to adopt time domain calculation to obtain thermal characteristics of the battery. To avoid the complicated calculations using time domain, 'state of charge (SOC)' can be used as an independent variable. A SOC based calculation method is elucidated through the comparison between the calculated results and experimental results together. Experiments are carried for rapid resistive discharge of a large-capacitive lithium secondary battery to evaluate variations of cell potential, current and temperature. Calculations are performed based on open-circuit cell potential (SOC,T), internal resistance (SOC,T) and entropy (SOC) with specific heat capacity.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.515-518
• /
• 2002

This paper presents the iterative procedure with the concept of expanded waves in the spectral and spatial domains using the fast modal algorithm. We presents its applications to microwave integrated circuits on resistive substrate. The advantage is a reduction in computation time. These calculated results are checked by comparison with the experimental and simulated results by Sonnet and Momentum program.