• 한국가시화정보학회지
• /
• 제18권1호
• /
• pp.11-17
• /
• 2020

The reduction of CO2 emissions has been a key target in the marine industry since the IMO's MEPC published its findings in 2009. Air lubrication method is one of the mature technologies for commercialization to reduce the frictional resistance and enhance fuel efficiency of ships. Since the air lubrication pattern varies according to the ship's standing position and injection flow rate, in order to effectively control the air lubrication system, it is necessary to be able to judge the air layer development state based on the information collected from the monitoring sensor. In this study, we performed the air lubrication ship simulation experiment to measure the void fraction and the frictional resistance. The void fraction was measured to confirm the behavior of the air. Through the measurement of the frictional resistance, the change in frictional resistance reduction rate from the injection point to the longitudinal direction of the ship was confirmed. Based on the measurement results, correlation analysis was performed on void fraction and frictional resistance reduction rate.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.263-266
• /
• 2002

Rises of temperature and resistance are observed in HTS tapes under over current condition. In this paper, we measured HTS tapes properties under low-over current condition with a little temperature rise as well as high-over current condition with a large temperature rise. According to the results of measurement, rises of temperature and resistance strongly depend on insulation level and duration of over current condition.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.617-620
• /
• 1998

In this paper we realized non-contact sheet resistance measurement system using eddy current. Proposed system is designed to meet the requirements which is necessary when dealing with conducting thin films on large area LCD panel. With several metals we could get lift-off curves which has the same trend as in principal. Especially in the region of high conductivity this system has more discriminating ability than 4-point probe system.

• 정보저장시스템학회논문집
• /
• 제8권1호
• /
• pp.16-21
• /
• 2012

SAW device is widely used as filters, sensors, actuators in various technologies. And capacitive sensor is tremendously used to measure pressure, gap, etc. The application of SAW device as signal conditioner of capacitive sensor reduces noise level and enables high precision measurement. The response increase of SAW based capacitive sensor is produced just before the two capacitive electrode contacts by the existence of parasitic resistance of capacitive electrode. In this paper, we analyze the effects of parasitic resistance and propose the calibrating method using lumped component and execute the high precision gap measurement using calibrated system. And xx nm resolution and yy ${\mu}m$ stroke was attained.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.352-355
• /
• 2009

The ground resistance has been used as a method of estimating the capability of counterpoise. When transient currents blow through a ground electrode, it is reasonable to evaluate the performance of ground electrode system as a ground impedance instead of ground resistance. However, the measurement method of ground impedance for counterpoise is not clearly presented. This paper describes the measurement method of ground impedance considering the earth mutual resistances and AC mutual coupling. When we measure the ground impedance, the error due to earth mutual resistances depends on the distance between the auxiliary electrodes and the electrode under test. The measurement accuracy of high frequency ground impedance is mainly influenced by the location of the current electrode and the potential electrode.

• 한국전자통신학회논문지
• /
• 제8권5호
• /
• pp.763-769
• /
• 2013

본 연구는 넙다리 부위의 근력 증진을 위해 순수 저항운동과 유산소 병행 저항운동의 효과를 비교해 임상에서 근력증진을 목적으로 한 운동 프로그램의 근거자료를 제공하고자 하였다. 넙다리 곧은근의 근활성도는 두 군 모두 실험전에 비해 실험후 통계적으로 유의한 차이가 있었고, 측정시기에 따른 군간 비교에서 순수 저항 운동군에 비해 유산소 병행 운동군이 통계적으로 유의한 차이가 있었다. 넙다리 곧은근의 두께는 두 군 모두 실험전에 비해 실험 후 유의한 차이가 없었으나, 측정 시기에 따른 군간비교에서 실험후에 순수 저항 운동군에 비해 유산소 병행 저항 운동군이 통계적으로 유의한 차이가 있었다. 결론적으로 근력 증진을 목적으로한 순수 저항 운동보다 저항 운동 후 유산소 운동을 실시하는 유산소 병행 운동이 근활성화 및 근 비대에 더 효과적임을 알 수 있었다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2006년도 춘계종합학술대회
• /
• pp.693-696
• /
• 2006

본 연구에서는 생체 임피던스의 변화를 계측하여 혈류량의 변화를 추정하기 위한 시스템을 구현하였다. 구현된 시스템은 인위적인 압력을 가하여 압력의 변화에 따른 임피던스의 변화량을 측정할 수 있도록 구성하였으며, 크게 압력 측정부와 4 전극법을 이용한 임피던스 측정부로 구분할 수 있다. 압력 측정부는 반도체식 압력센서와 센서의 출력신호를 처리하기 위한 전자회로부로 구성하였고, 임피던스 측정부는 교류 정전류원 회로와 임피던스 신호의 검출을 위한 락인 증폭기로 시스템을 구성하였다. 구현된 시스템의 성능평가를 위하여 표준저항을 이용한 임피던스 측정부의 특성조사 실험을 수행 하였다. 그리고 실제 실험군을 대상으로 임피던스의 계측을 통한 혈류량 변화 추정실험을 수행하였고, 혈류량 변화와 평균 동맥압을 이용한 혈류 저항비를 추정하였다 그 결과 혈류저항비와 혈류량의 변화는 반비례관계를 명확하게 보여 주었으며, 상관분석을 수행한 결과 상관계수가 -0.96776으로 강한 음의 상관관계를 나타내었다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.125-131
• /
• 2002

It is very important to assume potential distribution to be generated in electrode environs and grounding resistance by current beforehand, when incoming at grounding electrode to plan efficient grounding facilities In this paper, we analyzed grounding resistance through a simulation experiment by a water tank scaled model electrode of the rectangular earth plate, a theoretical Calculation result of the rectangular earth plate and measurement of grounding resistance buried rectangular earth plate analysing earth surface potential.

• 대한조선학회논문집
• /
• 제51권5호
• /
• pp.396-408
• /
• 2014

In this study, uncertainty analysis based on ITTC(International Towing Tank Conference) Recommended Procedures is carried out in the towing-tank experiment for motion responses and added resistance. The experiment was conducted for KVLCC2 model in head sea condition. The heave, pitch and added resistance were measured in different wave conditions, and the measurement was repeated up to maximum 15 times in each wave condition in order to observe the uncertainty of measured data. The uncertainty analysis was carried out by adopting the ISO-GUM(International Organization for Standardization, Guide to the Expression of Uncertainty in Measurements) method recommended by ITTC. This paper describes the details about the analysis method, uncertainty and the measured uncertainty for each source. The uncertainty analysis results are summarized as a tabular form. To validate the accuracy of the present measurement, the experimental results are compared with the results of numerical computation and other experiment. From the present uncertainty analysis, the main sources of uncertainty are identified, which can be very useful to improve the accuracy for added resistance experiment.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제8권4호
• /
• pp.155-166
• /
• 2008

PTH cracks are caused by the mismatch of coefficient of thermal expansion(CTE) between polymer and laminated materials, and are one of the main failure mechanisms of multi layer boards. In spite of its importance, it is usually hard to measure or detect them because of its small size and invisibility. To detect PTH cracks more effectively, this paper proposes a theoretical model that can estimate the resistance value from crack size of PTHs. Using four-point probe resistance measurement method, the resistance value of test coupons is measured. Through measured data, we verify the validity of the proposed theoretical model and set up criteria of failure.