• Journal of the Korean Institute of Gas
• /
• v.7 no.2 s.19
• /
• pp.22-32
• /
• 2003

Al-brass material is generally used at the state of plastic deformation, for example; bending, extension of bell mouth at shell and tube type heat exchanger. And SCC(stress corrosion cracking) of Al-brass material will be affected by residual stress as plastic deformation. SCC results from synergism between mechanical factor and corrosion environment. Mechanical factor is stress that directly relates with stress intensity factor at the crack tip. This paper was studied on the effect of stress on SCC of Al-brass tube under in $3.5\%$ NaCl. + $0.1\%\;NH_4OH$ solution by constant displacement tester. Increasing of acidified water flow into sea and speeds up corrosion rate of Al-brass which is used as a tube material of vessel heat exchanger by polluted coast seawater. The experimental results are as follow The latent time of SCC occurrence gets longer as the initial stress intensity factor($K_{Ii}$) gets lower The main crack was propagated as the initial stress intensity factor($K_{Ii}$) gets higher, and secondary cracks occurred by electro-chemical factor a(ter stage of released stress. Dezincification phase showed around the crack, and the range of dezincification gets wider as the initial stress intensity factor($K_{Ii}$) gets higher.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• Journal of Chest Surgery
• /
• v.29 no.11
• /
• pp.1197-1201
• /
• 1996

From October, 1987 to December, 1995, nine patients underwent total correction of tetralogy of Fallot in adults over 20 years of age. There were 5 male and 4 female patients aged from 22 to 42 years(mean, 29.6 years). Three patients were in New York Heart Association(NYHA) functional class II, and 6 patients in class III. The hemoglobin values ranged from 10.8 to 20.7 gm/㎗ (average, l5.6gm/㎗). The preoperative clinical features were as follows: cyanosis, 8 patients; dyspnea on exertion, 6 patients; clubbing of fingers, 5 patients; frequent upper respiratory infection, 3 patients. At the operation both infundibular and valvular stenosis were present in all patients. Reconstruction of right ventricular outflow tract(RVOT) using Goretex was required in 7 patients, and transannular patching with Goretex in 2 pateints. Left pulmonary angioplasty with pericardium was done in 2 patients. No hospital deaths occurred. Four of 9 patients(44.4%) had postoperative low cardiac output syndrome, and postoperative bleeding in 5. One patient required reoperation due to residual ventricular septal defect and tricuspid regurgitation 3 months after the first operation. The mean follow-up period was 25 months, range 11 to 77 months. All was asymptomatic and in NYHA class I. We suggest that advanced age is not contraindication to surgery in tetralogy of Fallot, and tetralogy of Fallot in adults could be operated on due to low mortality.

• Korean Journal of Materials Research
• /
• v.10 no.10
• /
• pp.703-708
• /
• 2000

As the engine design changes to get high efficiency and performance of commercial diesel engine, surface w wear of the earn follower becomes an important issue as applied load increasing at the contact face between cam follower and cam. We developed the ceramic cam follower made of sili$\infty$n nitride ceramic which was more wear resistant than the cast iron or sintered metal cam follower. Ceramic cam follower was made by direct brazing of thin ceramic disk to steel body using an active brazing alloy without the interlayer. In-situ crowning(R), resulted from the difference of thermal expansion coefficient between ceramic and carbon steel after direct brazing without any stress-relieving inter]ayer, could be controlled. When a earbon steel was heated above $A_{c1}$ point and then c$\infty$led, the expansion curve represented a hysteresis. Appropriate crowning was achieved below the $A_{c1}$ point(about $723^{\circ}C$) and crowning increased with brazing temperature exponentially above the $A_{c1}$ point. Optimum brazing temperature range was from 700 to $720^{\circ}C$. We developed successfully the ceramic cam follower having appropriate crowning and being inexpensive. Also we could successfully control the crowning of ceramic earn follower by hysteresis behavior of thermal expansion of earbon steel during direct brazing process.

• International Journal of High-Rise Buildings
• /
• v.10 no.4
• /
• pp.335-344
• /
• 2021

In structural engineering practice, understanding the performance of composite columns under extreme loading conditions such as high-rise bulding, long span and heavy loads is essential to accuratly predicting of material responses under severe loads such as fires or earthquakes. Hitherto, the combined effect of partial axial loads and subsequent elevated temperatures on the performance of hollow steel column filled fly ash concrete have not been widely investigated. Comprehensive test was carried out to investigate the effect of elevated temperatures on partial axially loaded square hollow steel column filled fly ash concrete as reported in this paper. Four batches of hollow steel column filled fly ash concrete ( 30 percent replacement of fly ash), (HySC) and normal concrete (CFHS) were subjected to four different load levels, n_f of 20%, 30%, 40% and 50% based on ultimate column strength. Subsequently, all batches of the partially damage composite columns were exposed to transient elevated temperature up to 250℃, 450℃ and 650℃ for one hour. The overall stress - strain relationship for both types of composited columns with different concrete fillers were presented for each different partial load levels and elevated temperature exposure. Results show that CFHS column has better performance than HySC at ambient temperature with 1.03 relative difference. However, the residual ultimate compressive strength of HySC subjected to partial axial load and elevated temperature exposure present an improvement compared to CFHS column with percentage difference in range 1.9% to 18.3%. Most of HySC and CFHS column specimens failed due to local buckling at the top and middle section of the column caused by concrete crushing. The columns failed due to global buckling after prolong compression load. After the compression load was lengthened, the columns were found to fail due to global buckling except for HySC02.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.7
• /
• pp.1043-1052
• /
• 2019

Active lipase-producing bacterium Burkholderia gladioli Bps-1 was rapidly isolated using a modified trypan blue and tetracycline, ampicillin plate. The electro-phoretically pure enzyme was obtained by purification using ethanol precipitation, ion-exchange chromatography, and gel filtration chromatography. The molecular weight was 34.6 kDa and the specific activity was determined to be 443.9 U/mg. The purified lipase showed the highest activity after hydrolysis with $p-NPC_{16}$ at a pH of 8.5 and $50^{\circ}C$, and the $K_m$, $k_{cat}$, and $k_{cat}/K_m$ values were 1.05 mM, $292.95s^{-1}$ and $279s^{-1}mM^{-1}$, respectively. The lipase was highly stable at $7.5{\leq}pH{\leq}10.0$. $K^+$ and $Na^+$ exerted activation effects on the lipase which had favorable tolerance to short-chain alcohols with its residual enzyme activity being 110% after being maintained in 30% ethanol for 1 h. The results demonstrated that the lipase produced by the strain B. gladioli Bps-1 has high enzyme activity and is an alkaline lipase. The lipase has promising chemical properties for a range of applications in the food-processing and detergent industries, and has particularly high potential for use in the manufacture of biodiesel.

• Korean Journal of Environmental Agriculture
• /
• v.40 no.2
• /
• pp.134-141
• /
• 2021

BACKGROUND: The analytical method was established for determination of fungicide chinomethionat in several animal commodities using gas chromatography (GC) coupled with electron capture detector (ECD). METHODS AND RESULTS: In order to verify the applicability, the method was optimized for determining chinomethonat in various livestock products including beef, pork, chicken, milk and egg. Chinomethionat residual was extracted using acetone/dichloromethane(9/1, v/v) with magnesium sulfate and sodium chloride (salting outassociated liquid-liquid extraction). The extract was diluted by direct partitioning into dichloromethane to remove polar co-extractives in the aqueous phase. The extract was finally purified with optimized silica gel 10 g. CONCLUSION: The method limit of quantitation (MLOQ) was 0.02 mg/kg, which was in accordance with the maximum residue level (MRL) of chinomathionate as 0.05 mg/kg in livestock product. Recovery tests were carried out at two levels of concentration (MLOQ, 10 MLOQ) and resulted in good recoveries (84.8~103.0%). Reproducibilities were obtained (Coefficient of variation <5.2%), and the linearity of calibration curves were reasonable (r²>0.995) in the range of 0.01-0.2 ㎍/mL. This established analytical method was fully validated and could be useful for quantification of chinomathionat in animal commodities as official analytical method.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.8
• /
• pp.23-30
• /
• 2021

In this study, we present a comparative analysis of major autoencoder(AE)-based anomaly detection methods for quality determination in the manufacturing process and a new anomaly discrimination criterion. Due to the characteristics of manufacturing site, anomalous instances are few and their types greatly vary. These properties degrade the performance of an AI-based anomaly detection model using the dataset for both normal and anomalous cases, and incur a lot of time and costs in obtaining additional data for performance improvement. To solve this problem, the studies on AE-based models such as AE and VAE are underway, which perform anomaly detection using only normal data. In this work, based on Convolutional AE, VAE, and Dilated VAE models, statistics on residual images, MSE, and information entropy were selected as outlier discriminant criteria to compare and analyze the performance of each model. In particular, the range value applied to the Convolutional AE model showed the best performance with AUC PRC 0.9570, F1 Score 0.8812 and AUC ROC 0.9548, accuracy 87.60%. This shows a performance improvement of an accuracy about 20%P(Percentage Point) compared to MSE, which was frequently used as a standard for determining outliers, and confirmed that model performance can be improved according to the criteria for determining outliers.

• Korean Journal of Environmental Agriculture
• /
• v.41 no.2
• /
• pp.135-151
• /
• 2022

BACKGROUND: The β-agonists known as phenyl ethanolamine derivatives have a conjugated aromatic ring with amino group. They are used as tocolytic agents and bronchodilator to human and animal generally, and some of them are used as growth promoters to livestock. METHODS AND RESULTS: β-agonists in samples were extracted by 0.4 N perchloric acid and ethyl acetate. The target compounds were analyzed by liquid chromatography-electrospray tandem mass spectrometry (LC-ESI-MS/MS). Validation of method was performed according to CODEX guidelines (CAC/GL-71). The matrix matched calibration gave correlation coefficients>0.98, and the obtained recoveries were in the range of 62.0-109.8%, with relative standard deviation ≤ 20.1%. In addition, a survey was performed to inspect any residual β-agonist from 100 samples of livestock and fishery products and ractopamine was detected in one of the 100 samples. CONCLUSION(S): In this study, we established the analytical method for β-agonists through using the expanded target compounds and samples. And we anticipate that the established method would be used for analysis to determine veterinary drug residues in livestock and fishery products.

• Journal of Food Hygiene and Safety
• /
• v.37 no.4
• /
• pp.238-248
• /
• 2022

This study was conducted to evaluate the safety of 208 types of residue pesticides on 150 dried agricultural products in Ulsan. The pesticide residues were detected using GC-MS/MS, LC-MS/MS, GC/ECD, GC/NPD, and LC/PDA. The detection rate was 19.3% (29 of 150 samples), and 28 types of pesticides were detected. Two of the 29 pesticide residues exceeded the maximum residue limit (MRL). Difenoconazole was detected in Ulleungdo aster, and chlorothalonil and chlorpyrifos were detected in chili pepper leaves. In the vegetable group, the frequency of pesticide residues was found to be the highest in dried leafy vegetables, followed by dried fruiting vegetables other than cucurbit vegetables, and then dried stalk and stem vegetables. The pesticide types detected in the commercial dried agricultural products were fungicide (60%), insecticide (23.8%), and acaricide (16.3%). In the validation study, the values of limit of detection (LOD), limit of quantitation (LOQ), coefficient of determination (R²), and recovery rate were in the range of 0.0001-0.0409 mg/kg, 0.0003-0.1241 mg/kg, 0.994-0.999, and 81.58-116.79%, respectively. The ratio of estimated daily intake (EDI)/acceptable daily intake (ADI) was 0.00002-0.31395%.