• Speech Sciences
• /
• v.15 no.3
• /
• pp.103-116
• /
• 2008

Cerebral palsy children represent abnormal vocalization pattern caused by respiration problem and paralyzed oral motor muscle that are the basics of speech production. Thus, this study examined the effect of respiration and articulator training programs on the basic ability of speech production in CP children. The subjects of this study were 4 children with 3 of spastic CP and 1 of ataxia CP. The respiration and articulator program was conducted in 30 sessions for 30 minutes each. Pre-test was administered twice before the program, ongoing test was administered every 5 session during the period of experiment, and post-test was administered twice. The program included speech production such as respiration training, lips, jaw, cheek, and tongue exercise, and velopharyngeal training, and related articulator training. The following results were obtained. First, all subject children were less than 5 seconds in maximum phonation time before the experiment and 2 were improved by more than 4$\sim$5 seconds during the experiment, but 2 had relatively low rising width. Second, while children with less than 30dB before the experiment became bigger in strength during the experiment, children with more than 35dB before the experiment showed a minor change. Subject child 4 had lower vocal strength in the post-test period. Finally, although each subject had individual difference in syllable diadochokinetic ability, the function was improved and the number of repetition in one respiration was also increased.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.110-113
• /
• 2006

A high rate deposition sputtering process of magnesium oxide thin film in oxide mode has been developed using a 20 kW unipolar pulsed power supply. The power supply was operated at a maximum constant voltage of 500 V and a constant current of 40 A. The pulse repetition rate and the duty were changed in the ranges of $10\sim50$ kHz and $10\sim60%$, respectively. The deposition rate increased with rising incident power to the target. Maximum incident power to the magnesium target was obtained by the control of frequency, duty and current. The deposition rate of a moving state was 9 nm m/min at the average power of 1.5 kW. This result shows higher deposition rate than any other previous work involving reactive sputtering in oxide mode. The thickness uniformities over the entire substrate area of $982mm{\times}563mm$ were observed at the processing pressure of $2.8\sim9.5$ mTorr. The thickness distribution was improved at lower pressure. This technique is proposed for application to a high through-put sputtering system for plasma display panels.

• Korean Journal of Optics and Photonics
• /
• v.15 no.3
• /
• pp.263-267
• /
• 2004

We have investigated the characteristics of a Nd:YAG laser pumped by a cw Ti:sapphire laser. When the pumping power of the Ti:sapphire laser was 850 ㎽, the maximum output power of the Nd:YAG laser was 450 ㎽. As a result, the slope efficiency for the output power of the Nd:YAG laser was measured to be 56%. We have also investigated the characteristics of a passively Q-switched Nd:YAG laser by using a Cr$^{4+}$:YAG as saturable absorber with initial transmission of 90%. The maximum average output power of 200 ㎽ was obtained with repetition rate of 23.8 KHz and pulse width of 17.0 ns.

• Journal of the Korea Society of Computer and Information
• /
• v.6 no.2
• /
• pp.8-13
• /
• 2001

We demonstrate a pulsed CO$_2$laser with long pulse duration of millisecond order in the low pressure less than 30 Torr. A new power supply for our laser system switches the voltage of AC power line(60㎐) directly. The power supply doesn't need elements such as a rectified bridge, energy-storage capacitors. and a current-limiting resistor in the discharge circuit. In order to control the laser output power, the pulse repetition rate is adjusted up to 60㎐ and the firing angle of SCR gate is varied from 30˚ to 150˚. A ZCS(Zero Crossing Switch) circuit and a PIC one-chip microprocessor are used to control the gate signal of SCR precisely. The maximum laser output is 23W at the total pressure of 18 Torr, the pulse repetition rate of 60㎐, and SCR gate firing angle of 90˚. In addition, the obtained laser pulse width is approximately 3㎳(FWHM)

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.286-291
• /
• 2015

LLC resonant converter is used to control laser output power in Nd:YAG laser. Zero voltage switching (ZVS) is implemented to minimize the switching loss which is adopting the LLC resonant converter. In the spot welding processing of metal thin films, the processing quality is decided by the laser beam output energy of single pulse. We decide to the 50 [J] as the single pulse laser beam energy. Laser output power is investigated and experimented by changing the output current. That current is controled by the charging voltage of capacitor. From those results, we obtained the maximum laser output of 58.2 [J] and the conversion efficiency of 2.52% at the discharge voltage of 620V and the discharge current of 861 [A] and the pulse repetition rate of 1 [Hz] at the charging capacitor of 12,000 [${\mu}F$].

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.14-18
• /
• 2006

Optical interferometer is used for various optical measurement fields in optical metrology and biomedical measurements. In an optical interferometer, optical delay line has to change the optical path length of a reference arm to match with that of a sample in and it's speed was limited by reference arm movement speed. In this paper, we proposed an all-fibered RSODRapid Scanning-speed Optical Delay) without any mechanical movement, and we applied this system to optical interferometer. Experimental setup is consist of pulse laser source (center wavelength 1304nm, pulse width 30ps, repetition rate 10GHz), two phase modulators and dispersive shifted fiber. As experimental results, we obtain the maximum time delay of 11ps at 10MHz repetition rate, and it is easily tuneable the time delay by modulation frequency and modulation voltage.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.4 s.316
• /
• pp.44-50
• /
• 2007

In this paper, we proposed the algorithm for the extraction of the corresponding points from images. The proposed algorithm EMSAC is based on RANSAC and EM algorithms. In the RANSAC procedure, the N corresponding points are randomly selected from the observed total corresponding points to estimate the homography matrix, H. This procedure continues on its repetition until the optimum H are estimated within number of repetition maximum. Therefore, it takes much time and does not converge sometimes. To overcome the drawbacks, the EM algorithm was used for the selection of N corresponding points. The EM algorithm extracts the corresponding points with the highest probability density to estimate the optimum H. By the experiments, it is demonstrated that the proposed method has exact and fast performance on extraction of corresponding points by combining RANSAC with EM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.12A
• /
• pp.951-957
• /
• 2003

The analysis of RF performance requirement conditions on communication system is critical indicator to predict the performance of system. UWB(Ultra Wide Band) system which the standard is not established yet is difficult to derive the precise system performance requirement condition. Also, there are differences between conventional UWB system and multi-band system about RF performance requirement condition. In this thesis, the differences are analyzed and performance requirement conditions of multi-band UWB system are described on the basis of the differences. Throughput, maximum transmit power, and sensitivity of multi-band UWB system is varied with respect to the number of Sub-Bands. In addition, because of Multi-path effect, if PRF(Pulse Repetition Frequency) is changed, the Multi-path link margin is happened to compensate for Multi-path Energy Loss which is contributed by increasing of the Link Margin. According to Multi-path Margin, the variation of the resistance with respect to sensitivity and interference signal is observed and analyzed through the simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.307-313
• /
• 2019

The traveling wave tube amplifier (TWTA), which can be applied to the Ka-band millimeter-wave multi-mode seeker, consists of an high voltage power supply(HVPS), a grid modulator, a command and control, and an RF assembly. We designed a power supply that generates a -17.9 kV high voltage by synchronizing the pulse repetition frequency(PRF) and power supply switching frequency(i.e. synchronization frequency), and a high-speed grid-switching modulator for RF pulse modulation. The TWTA, which is fabricated through miniaturization with a volume of 3.18 L, has high pulse switching characteristics of up to 18.5 ns. The maximum rise/fall time of the grid on/bias signal and peak power is more than 564.9 W. Moreover, an excellent spurious performance of -68.4 dBc or less was confirmed within the range of PRF and PRF/2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.136-141
• /
• 2021

Heating cables, widely used in office buildings, factories, streets and railways, deteriorate in electrical insulation during operation. The insulation deterioration of heating cables leads to electric discharges that can cause electrical fires. With this background, this paper dealt with a condition monitoring technique for heating cables by the analysis of discharge signals to prevent electrical fires. Insulation deterioration was simulated using an arc generator specified in UL1699 under AC operation, and the characteristic and propagation of discharge signals were analyzed on a 100 meter-long heating cable. Discharge signals produced by insulation deterioration were detected as a voltage pulse because they are as small as a few mV and they are attenuated through propagation path. The frequency spectrum of discharge signals mainly existed in the range from 70 kHz to 110 kHz, and the maximum attenuation of the signal was 84.8% at 100 meters away from the discharge point. Based on the experimental results, a monitoring device, which is composed of a high pass filter with the cut-off frequency of 70 kHz, a comparator, a wave shaper and a microprocessor, was designed and fabricated. Also, an algorithm was designed to discriminate the discharge signal in the presence of noise, compared with the pulse repetition period and the number of pulse counts per 100ms. In the experiment, the result showed that the prototype monitoring device could detect and discriminate the discharge signals produced at every discharge point on a heating cable.