• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1871-1873
• /
• 1997

The conventional current transformers are often take faults and out of order that for detect to over current of electric power lines because electromagnetic interference. But, it is possible to implement protection relay of high reliability using optical magnetic field sensor which are immunity and small size. The optical magnetic field sensor is possible to rapidly detect to over current and recover when electric power line have fault. And it is not necessary to make with capacitance of electric power lines as optical magnetic field sensor is have linearity from 0 to about 20kA. In this study, we designed and constructed compensative feedback circuit in order to minimize of optical power intensity variation with environ- mental variations(temperature, drive current) of light source. And this system have highest optical advantages and reliability.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 D
• /
• pp.2584-2586
• /
• 2000

A drum level control is one of the most important control systems in thermal power plant. The control objective of drum level of boiler in thermal power plant is to maintain drum level at constant set-point regardless of disturbance such as main steam flow. The implemented drum level controller is the cascade PI controller. The important factor in drum level controller is the parameters of two PI controllers. The tuning of PI controller parameter is tedious and time-consuming job. In this paper, the relay feedback Ziegler - Nichols tuning method extended to auto-tune cascade PI drum level controller. Finally, the simulation result using boiler model in Power Plant shows the validity of auto-tuned cascade PI controller.

• 전기의세계
• /
• 제13권2호
• /
• pp.5-10
• /
• 1964

Some nonlinearities in feedback control systems, such as relay servo, Coulomb friction, saturating amplifier of backlash in gears cause some undesirable effects. These may be static errors, limit cycles or jump phenomena. So, linearizing method of these nonlinearities using dither signals was first suggested by Loeb. He pointed out that the addition of high frequency signal to either the input or the output of a nonlinear system would make the nonlinear performance approximate the performance of linear systems. He used high-frequency sinusoidal wave as dither signal. But, in this thesis, general method of analysis is suggested for nonlinear control systmes using various dither signals, such as noise signal of Gaussian amplitude distribution, sinusoidal dither signal and sawtooth dither signal. Also, the advantage and disadvantage of these dither signals are compared. Throughout the analysis statistical method is adopted and lastly analog computer is used for the experiment of various nonlinear systems using dither signals.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.424-428
• /
• 2004

A wind turbine system converts wind energy into electric energy, the system operated under normal environmental conditions. In case of particular turbulent wind flow such as typhoon, hurricane etc, the control of a blade used to a yaw control and a pitch control method. A small wind turbine has not a speed control system to only a manual tail safety brake. This paper shows a automatic tail safety brake controller based on feedback control using wind velocity. The controller composed of wired motor, relay system, steel wired motor him down a perpendicular to wind flow and then the blade speed reduced high to zero. The operation of automatic tail safety controller verified by manual test.

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.103-115
• /
• 2002

This paper describes the results on the design and implementation of large capacity cable checking system using I/O buffer method. The I/O buffer module which has feedback loops with input and output buffers is designed with logic gate in the VME board and controlled by MPC860 microprocessor. So this system can check a lot of cable at the same time with less size and less processing time than that of relay matrix method with the A/D converter. The size of the I/O buffer module can be variable according to the number of cable. And any type of cable can be checked even if the pin assignment of cable is changed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 A
• /
• pp.436-438
• /
• 1993

A rule based fuzzy expert system in self-tune PID controllers is presented in this paper. The rule base. the core of the expert system, is extracted from the Wills' tuning map and the author's knowledge about the implicit relations between PID gains and controlled output response. The overall control system consists of the relay feedback scheme and the expert system, where the one is responsible for initial tuning and the other for subsequent tuning. The PID control system with the proposed fuzzy expert system, shows better convergence rate and control performances than those of a Litt in spite of the fact that the two rule bases are extracted from the same maps provided by Wills.

• 한국통신학회논문지
• /
• 제35권1C호
• /
• pp.1-7
• /
• 2010

본 논문은 하나의 소스, 하나의 릴레이, 그리고 하나의 목적 노드가 각각 두 개의 송수신 안테나를 갖는 협력 통신망에서, 연판정 후 전달(soft-decision-and-forward: SDF) 방식의 성능을 쌍 오류 확률(pairwise error probability: PEP)을 이용해 분석한다. 준정지 레일리 페이딩 채널에서 최적 그리고 차선의 전력 분배비를 결정한다. 최적의 전력 분배는 평균 PEP를 최소로 하는 것이나 일반적으로 구하기 어려우므로, 다이렉트와 릴레이 링크의 잡음 대 신호비의 곱(product signal-to-noise ratio: product SNR)을 최대화하는 전력 분배 전략을 고려한다. 모의실험 결과를 통해 높은 SNR 구간에서는 차선의 전력 분배 방식의 성능이 최적의 성능에 근접함을 보인다.

• 한국산학기술학회논문지
• /
• 제13권12호
• /
• pp.6027-6033
• /
• 2012

본 논문은 릴레이 피드백을 이용한 주파수 영역에서 내부 및 외부 모델을 동정하고 이 모델을 바탕으로 IMC-Cascade 제어기 파라미터 자동 동조 알고리즘을 제안하였다. 모델 동종 방법은 정상상태와 과도상태를 고려하여 1차의 지연모델로 동정 하였으며, 내부 제어기 및 외부 제어기의 제어 파라미터는 동정된 모델을 활용하여 성능지수 ITAE값이 최소로 되도록 자동동조 하였다. 시뮬레이션 결과 제안된 방법이 기존의 방법보다 우수함을 확인할 수 있었다.

• 디지털산업정보학회논문지
• /
• 제11권1호
• /
• pp.97-109
• /
• 2015

In this paper, we design and implement a two-way automatic communication system using a mobile instant messenger that can provide a customized service through a real-time two-way communication using a mobile instant messaging service. Two-way automatic communication system using a mobile instant messenger can improve the quality and quantity of information in real-time update of the information through the feedback. In addition, since it is communicated by using a mobile Instant Messanger in 1:1 there is no concerns that is recognized as spam, as well as it is possible to provide customized information for each user. Two-way automatic communication system using a mobile instant messanger shows the difference of the speed according to the data input time in typing by hands in result of comparing the time to input a date and the processing speed to search a data. Therefore in category treatment, command processing and natural language processing, Category treatment way is the most excellent in aspect of data processing speed, otherwise in aspect of the total speed to combine the data input time and the processing time, the command processing way is the best method.

• 디지털산업정보학회논문지
• /
• 제10권3호
• /
• pp.11-21
• /
• 2014

In this paper, concerning the various advertising and policy advertising of the election with respect to whether to deliver a message to a large number of people, we design and implement an automative system what enables sending the text messages directly from the server to the client and also fast feedback is enabled by utilizing a number of operational programs to connect to the server. Therefore, we design and implement the automative communication system which enables delivering message to each user mobile terminal from a plurality of relay mobile terminals by utilizing the mobile instant messenger, not to deliver a message from the server to the mobile instant messenger user directly. In result of comparative analysis on the number of times of data transmission, this automative communication system utilizing mobile instant messenger shows the result that it enables transmitting five times per minute as it can copy and paste in the automation system regardless of the size of the data loading, otherwise in case of transmitting manually it show the result that the number of times of data transmission is reduced if the size of the data is larger.