• 한국정보통신학회논문지
• /
• 제11권10호
• /
• pp.1910-1915
• /
• 2007

본 논문에서는 NQS(non-quasi-static)효과를 고려한 FD(fully depleted)-SOI(silicon-on-insulator) MOSFETs의 고주파 소신호 모델링을 위한 등가회로 변수들을 간단하고 정확히 추출하는 방법을 제시하였다. 제시된 추출방법은 임피던스와 어드미턴스 행렬계산으로 S-파라미터의 측정 결과로부터 MOSFET의 외부 기생용량과 기생저항을 제거하여 물리적인 특성을 바탕으로 한 MOSFET의 내부등가회로변수가 간단히 추출되어진다. 제시된 방법으로 등가 회로를 구한 후 Y-파라미터를 계산하여 측정치와 비교한 결과 500MHz부터 200Hz까지 잘 일치함을 확인하였다.

• Steel and Composite Structures
• /
• 제25권6호
• /
• pp.727-734
• /
• 2017

This paper describes a quasi-static finite element analysis, which uses the explicit integration method, of the apex joint of a cold-formed steel portal frame. Such cold-formed steel joints are semi-rigid as a result of bolt-hole elongation. Furthermore, the channel-sections that are being connected have a reduced moment capacity as a result of a bimoment. In the finite element model described, the bolt-holes and bolt shanks are all physically modelled, with contact defined between them. The force-displacement curves obtained from the quasi-static analysis are shown to be similar to those of the experimental test results, both in terms of stiffness as well as failure load. It is demonstrated that quasi-static finite element analysis can be used to predict the behavior of cold-formed steel portal frame joints and overcome convergence issues experienced in static finite element analysis.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.273-278
• /
• 2016

This study makes a relative comparison of the results of tensile test and quasi-static analysis using AGL(Adjuster Guide Loop) model that plays a role in adjusting the height of shoulder belt, of the components of the vehicle seatbelt system and attempts to propose a method of reducing the error rate of the quasi-static analysis technique effectively. This study selects two major factors affecting the result of an analysis, draws the result of analysis through the method of experimental design, one of the statistical techniques and understands the contribution rate of the major factors affecting the result of the analysis through ANOVA(Analysis of Variance).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.402-407
• /
• 2001

Sensitivity analysis scheme is developed in the elasto-plastic finite element method with explicit time integration using direct differentiation method. The direct differentiation is concerned with the time integration, constitutive relation, shell element with reduced integration and the contact scheme. Sensitivity analysis results are mainly examined with the highly nonlinear and quasi-static problem with the complicated contact condition. The result shows stable sensitivity especially in the sheet metal forming analysis.

• 마이크로전자및패키징학회지
• /
• 제12권1호
• /
• pp.17-20
• /
• 2005

In this paper, we presented the quasi-static characteristics of novel microstrip lines with anisotropic grooved dielectric in finite metal. A quasi-static mode-matching method has been used to analyze this new structure and the simulation results are validated through comparison with other available results. The results in this paper show that it is possible to control the propagation characteristics of microstrip lines with the use of anisotropic grooved dielectric in finite metal. Also anisotropic grooved dielectric in microstrip line can be newly added to the design parameters of high performance three dimensional monolithic microwave circuits and other microwave applications.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 1998년도 춘계 학술논문발표회 논문집
• /
• pp.257-262
• /
• 1998

In order to understand the characteristics of electrostatic discharge (ESD) by a charged human body, a dynamic analysis method based on RCL circuit and a quasi-static analysis method based on two-body model are introduced. In this paper, these methods calculate waveforms, discharge energy and potential difference to analyze the ESD phenomena from given initial conditions and geometry. Results are compared and discussed.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.183-188
• /
• 1996

The compressive stress-strain response of Low Density Polyurethane foam material is modeled using the finite element method. A constitutive equation which include experimental constants based on quasi-static and dynamic uniaxial compression test is proposed. Impact test with different impactor masses and velocities are performed to verify the proposed model. The comparison between impact test and finite element analysis shows good agreements.

• Structural Engineering and Mechanics
• /
• 제81권4호
• /
• pp.411-428
• /
• 2022

This paper presents the Campbell diagram analysis of the rotordynamic system using the full order model (FOM) and the reduced order model (ROM) techniques to determine the critical speeds, identify the stability and reduce the computational time. Due to the spin-speed-dependent matrices (e.g., centrifugal stiffening matrix), several model order reduction (MOR) techniques may be considered, such as the modal superposition (MS) method and the Krylov subspace-based MOR techniques (e.g., Ritz vector (RV), quasi-static Ritz vector (QSRV), multifrequency quasi-static Ritz vector (MQSRV), multifrequency/ multi-spin-speed quasi-static Ritz vector (MMQSRV) and the combined Ritz vector & modal superposition (RV+MS) methods). The proposed MMQSRV method in this study is extended from the MQSRV method by incorporating the rotational-speed-dependent stiffness matrices into the Krylov subspace during the MOR process. Thus, the objective of this note is to respond to the question of whether to use the MS method or the Krylov subspace-based MOR technique in establishing the Campbell diagram of the shaft-disc-blade assembly systems in three-dimensional (3D) finite element analysis (FEA). The Campbell diagrams produced by the FOM and various MOR methods are presented and discussed thoroughly by computing the norm of relative errors (ER). It is found that the RV and the MS methods are dominant at low and high rotating speeds, respectively. More precisely, as the spinning velocity becomes large, the calculated ER produced by the RV method is significantly increased; in contrast, the ER produced by the MS method is smaller and more consistent. From a computational point of view, the MORs have substantially reduced the time computing considerably compared to the FOM. Additionally, the verification of the 3D FE rotordynamic model is also provided and found to be in close agreement with the existing solutions.

• Composites Research
• /
• 제24권1호
• /
• pp.1-9
• /
• 2011

본 논문에서는 복합재료 튜브를 이용한 고속 열차의 에너지 흡수장치에 대한 실험 및 수치 해석에 관한 연구를 수행하였다. 논문의 목적은 에너지 흡수장치에 대한 최적의 적층(lay-up) 형태를 알아내는 것으로, quasi static method를 이용한 네 가지 적층 형태에 대한 실험을 수행 하였다: $[0/45/90/-45]_4$, $[0]_{16}$, $[0/90]_8$, $[0/30/-30]_5$, 실험을 위해 초기 파괴 시작점을 생성하고, 일정 방향으로 진행되는 파괴를 만들기 위해 베벨 엣지(bevel edge)와 노치 엣지(notch edge)의 두 가지 트리거링 방법을 이용하였다. 저속 충돌실험 결과 $[0/45/90/-45]_4$의 적층 형태가 다른 방법과 비교해서 가장 좋은 에너지 흡수 결과를 보여주였다. 수치해석을 위해 LS-DYNA 프로그램의 변수 분석(parametric analysis)을 통해 가장 적합한 복합재료의 quasi static 실험 시뮬레이션 방법 연구를 수행하였다. 움직이는 벽이 복합재 튜브에 저속 충돌하는 모델을 가정하여 해석을 수행하였으며, 실험값과 수치해석 결과의 비교를 통해 비슷한 경향을 보임을 확인 하였다. 특히 TFAIL과 mass scaling factor를 조절하며 수행하는 변수 분석은 LS-DYNA에서 복합재 튜브의 quasi static 실험을 시뮬레이션 하는 능력과 한계를 보여준다.

• Nuclear Engineering and Technology
• /
• 제50권6호
• /
• pp.971-980
• /
• 2018

Using the concept of quasi-static decomposition and using three-noded isoparametric locking-free element, this article presents a formulation of the finite element method for Timoshenko beam subjected to spatially different time-dependent motions at supports. To verify the validity of the formulation, three fixed-hinged beams excited by the real seismic motions are examined; one is a slender beam, another is a stocky one, and the other is an intermediate one. The numerical results of time histories of motions of the three beams are compared with corresponding analytical solutions. The internal loads such as bending moment and shearing force at a specific time are also compared with analytic solutions. These comparisons show good agreements. The comparisons between static components of the internal loads and the corresponding total internal loads show that the static components predominate in the stocky beam, whereas the dynamic components predominate in the slender one. Thus, the total internal loads of the stocky beam, which is governed by static components, can be predicted simply by static analysis. Careful numerical experiments indicate that the fundamental frequency of a beam can be used as a parameter identifying such a stocky beam.