• Journal of Powder Materials
• /
• v.23 no.5
• /
• pp.384-390
• /
• 2016

Tri-isotropic (TRISO) coatings on zirconia surrogate beads are deposited using a fluidized-bed vapor deposition (FB-CVD) method. The silicon carbide layer is particularly important among the coated layers because it acts as a miniature pressure vessel and a diffusion barrier to gaseous and metallic fission products in the TRISO-coated particles. In this study, we obtain a nearly stoichiometric composition in the SiC layer coated at $1400^{\circ}C$, $1500^{\circ}C$, and $1400^{\circ}C$ with 20 vol.% methyltrichlorosilane (MTS), However, the composition of the SiC layer coated at $1300-1350^{\circ}C$ shows a difference from the stoichiometric ratio (1:1). The density decreases remarkably with decreasing SiC deposition temperature because of the nanosized pores. The high density of the SiC layer (${\geq}3.19g/cm^2$) easily obtained at $1500^{\circ}C$ and $1400^{\circ}C$ with 20 vol.% MTS did not change at an annealing temperature of $1900^{\circ}C$, simulating the reactor operating temperature. The evaluation of the mechanical properties is limited because of the inaccurate values of hardness and Young's modulus measured by the nano-indentation method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.4
• /
• pp.1059-1066
• /
• 2008

Characteristics of pyrolysis and liquid product distribution of ABS plastics have been studied in the thermogravimetric(TG) reactor and bomb microreactor. Pyrolysis reactions were performed at temperature $400\sim450^{\circ}C$ and yield of each pyrolytic product was obtained by the weight measurement method. The molecular weight distributions of liquid products were determined by the GC-SIMDIS method. It was observed that solid residue which could not be detected in the thermogravimetric experiments was significantly formed in the batch-type microreactor. It was found that the yield and average molecular weight of liquid products were decreased with the increase of reaction temperature and time. but the formation of styrene monomer was significantly increased. The chain-end scission rate parameters were determined to be 54.1kcal/mole far ABS by the Arrhenius plot.

• Korean Chemical Engineering Research
• /
• v.48 no.1
• /
• pp.110-115
• /
• 2010

The experiment was designed to compare pyrolysis kinetics of two different classes of imported coal. The pyrolysis behaviors of the coals were first observed with thermogravimetric analyzer(TGA). The kinetic analysis was further done based on a new distributed activation energy model(New DAEM). During the analysis, weight loss curves measured at three different heating rates were used to obtain the activation energy distribution function curve f(E) of a given coal sample where a mean activation energy is determined by its peak. The results show a significant difference in the mean activation energy between two coals for the pyrolytic reaction. The prediction of a chemical percolation devolatilization(CPD) model where the kinetics obtained from the New DAEM method were incorporated is in much closer agreement with an experimental data of TGA particularly for the bituminous coal.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.47-58
• /
• 2005

Rice straw is one of the main renewable energy sources in Korea, and bio-oil is produced from rice straw with a lab. scale plant equipped mainly with a fluidized bed and a char removal system. We investigated how the reaction temperature affected the production of bio-oil and the efficiency of a char removal system. To elucidate how the temperature depended on the production of bio-oil, experiment were conducted between $450^{\circ}C\;and\;600^{\circ}C$ with a feed rate of about 300g/h. The mass balance was established in each experiment, and the produced gas and oil were analyzed with the aid of GCs and a GC-MS system. The char removal system is composed of a cyclone and a hot filter. In the experiments, we observed that the optimum reaction temperature range for the production of bio-oil is between $450^{\circ}C\;and\;500^{\circ}C$.

• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.2
• /
• pp.176-183
• /
• 2000

This study was conducted to compare the volatile components of lamina(cutter group) and midrib of flue-cured tobacco leaves by two analytical methods, Curie-Point pyrolysis and Purge & Trap headspace technique. The pyrolysis of lamina and midrib part of tobacco leaves was performed at the temperature of $330^{\circ}C$, $650^{\circ}C$, and $920^{\circ}C$ by Curie-Point Pyrolyzer, and 33 compounds were identified in the pyrolyzates by GC/MSD. The composition of the components identified showed a quite difference between lamina and midrib. However, the amount of the pyrolyzed products from the both of lamina and midrib was increased with temperature increase except that of acetic acid, furfural, and nicotine. The content of phenolic compounds including phenol, 4-methyl phenol, and 3-methyl phenol was higher in midrib than in lamina, while that of furan compounds such as 2,3-dihydrobenzofuran, 5-hydroxymethyl furfural, was high in lamina. Interestingly, acetamide, 2-propenamide and 3-acetoxy pyridine were not defected in the pyrolyzates of lamina. By Purge & Trap headspace technique, 28 volatile components were identified in both lamina and midrib. The composition of the identified compounds and their chromatograpic patterns also showed the complete difference between the two. The content of solanone, $\beta$-damascone, $\beta$-damascenone, and megastigmatrienones, key components of tobacco aroma, was much higher in lamina than in midrib. The results indicate that lamina contains much more carbonyl compounds known to enhance the smoke taste of cigarette, whereas midrib takes nitrogenous and phenolic compounds, which are known to cause a deteriorate effect of smoke such as irritation.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1137-1143
• /
• 1999

The change of physicochemical characteristics of sesame with roasting temperature$(110^{\circ}C{\sim}230^{\circ}C)$ were investigated to get a useful index which needs to manufacture roasted sesame and sesame oils, In the physicochemical properties of roasted sesame, the contents of moisture, specific volume, oil yields and sesame cakes were changed significantly above $170^{\circ}C$. Fat and protein in sesame cakes were changed slightly. Desirable roasting temperature was $220^{\circ}C$ in considering oil yields and sensory qualities. Total amino acids such as arginine, serine, threonine, lysine. cystine, tyrosine and most of the free amino acids, and sucrose of free sugars were reduced significantly above $170^{\circ}C$ and $190^{\circ}C$. respectively. These reductions of sugar and amino compounds were assumed to play an important role in Maillard reaction for the formation of browning pigment, taste and aroma. It was confirmed that this reaction was pyrolytic degradation which took place in water-deficient and oil-rich system at relatively high temperature.

• Journal of Environmental Science International
• /
• v.14 no.2
• /
• pp.105-119
• /
• 2005

The surface sediments inside Songsanpo and Seogwipo Harbors, major harbors of Jeju Island, were collected three times (June, September and December, 2001) and analyzed for 16 polycyclic aromatic hydrocarbons (PAHs) recommended by US-EPA as priority pollutants to assess their distribution levels and their biological effects on the marine organisms, and to suggest their possible origins. The concentrations of total PAHs inside Songsanpo and Seogwipo Harbors ranged from 41 to 288 ng/g on a dry weight basis with a mean value of 121 ng/g and from 14 to 268 ng/g with a mean value of 119 ng/g, respectively, and the levels were low as compared with those in other areas of the world. The sedimentary PAHs may be correlated with organic carbon and mud content to some extent. Based on comparisons of individual and total concentrations with effects-based sediment quality guidelines, the potential for the biological effects on the marine organisms were expected to be very low. From the examinations of the four PAH origin indices, such as LMW /HMW (low molecular weight 2-3 ring PAHs over high molecular weight 4-6 ring PAHs), phenanthrene/anthracene ratio, fluoranthene/pyrene ratio, chrysene/benzo[a]anthracene ratio, it can be concluded that the sediment PAH contaminations were ascribed to both of pyrolytic and petrogenic origins.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.8 s.173
• /
• pp.165-173
• /
• 2005

This paper presents the results for deposition of micrometer-scale metal lines on glass for the development of TFT-LCD circuit repair-system. Although there had been a few studies in the late 1980's for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and W(CO)s was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 m depending on laser power and scan speed while the width was controlled between 50um using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below $1{\Omega}{\cdotu}um$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.

• Journal of Energy Engineering
• /
• v.19 no.1
• /
• pp.16-20
• /
• 2010

In present work, tin-carbon mixtures by using carbon from pyrolyzed coffee seeds were synthesized. Synthesis methods includes simple mixing and chemical mixing. X-ray diffraction pattern indicated carbon and tin mixture peaks and scanning electron microscope images showed particles size of $12{\sim}85\;{\mu}m$ and shape. Charge discharge test were carried out. Tin-carbon mixture by chemical mixing indicated higher discharge capacity of 191 mAh/g than commercial carbon black(105 mAh/g) for 15cycles. Tin-carbon mixture by simple mixing indicated similar performance to carbon black.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.106-115
• /
• 2002

Growth characteristics of micro carbon structures fabricated by laser-assisted chemical vapor deposition are studied. Argon ion laser and ethylene were used as the energy source and reaction gas, respectively, to grow micro carbon rod through pyrolytic decomposition of the reaction gas. Experiments were performed at various conditions to investigate the influence of process parameters on growth characteristics such as the diameter or growth rate of the micro carbon rod with respect to reaction gas pressure and incident laser power. Reaction gas pressure in experiments ranges from 200 to 600Torr and the incident laser power from 0.3 to 3.8W. For these conditions, the diameter of the rod increases linearly with respect to the laser power but is almost independent of the reaction gas pressure. Growth rate of the rod changes little with gas pressure when the laser power remains below IW. For a constant reaction gas pressure, the growth rate increase with Increasing laser power, but the rate of increase decreases gradually, implying that the chemical vapor deposition condition changes from a kinetically-limited regime to a mass-transport-limited regime. When the carbon rod was grown at near threshold laser power, a very smooth surface is obtained on the rod. By continuously moving the focusing lens in the direction of growth, a micro carbon rod with a diameter of 287${\mu}{\textrm}{m}$ and aspect ratio of 100 was fabricated..