• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1540-1551
• /
• 2015

The detection of position and speed in BLDC motors without using position sensors has meant many efforts for the last decades. The aim of this paper is to develop a sensorless technique for detecting the position and speed of BLDC motors, and to overcome the drawbacks of position sensor-based methods by improving the performance of traditional approaches oriented to motor phase voltage sensing. The position and speed information is obtained by computing the derivative of the terminal phase voltages regarding to a virtual neutral point. For starting-up the motor and implementing the algorithms of the detection technique, a FPGA board with a real-time processor is used. Also, a versatile hardware has been developed for driving BLDC motors through pulse width modulation (PWM) signals. Delta and wye winding motors have been considered for evaluating the performance of the designed hardware and software, and tests with and without load are performed. Experimental results for validating the detection technique were attained in the range 5-1500 rpm and 5-150 rpm under no-load and full-load conditions, respectively. Specifically, speed and position square errors lower than 3 rpm and between 10º-30º were obtained without load. In addition, the speed and position errors after full-load tests were around 1 rpm and between 10º-15º, respectively. These results provide the evidence that the developed technique allows to detect the position and speed of BLDC motors with low accuracy errors at starting-up and over a wide speed range, and reduce the influence of noise in position sensing, which suggest that it can be satisfactorily used as a reliable alternative to position sensors in precision applications.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.294-299
• /
• 2010

ELT(Emergency Locator Transmitter) is used to send distress signal in the event of an aircraft crash. It is very useful but the ELT may transmit wrong signal caused by misjudging between crash and hard-landing. The reason of this problem is the low accuracy of the mechanical G-switch currently in use. To improve the ELT, we developed an ELT system using the MEMS(Micro Electro-Mechanical Sensor) accelerometer. The ELT system consists of acceleration data acquisition/analysis system, program of crash recognition, and GPS receiving system for the position information of an aircraft crash site. A free-drop table was developed for verification of the ELT system. The free-drop table was designed to replicate the acceleration and the pulse duration of the hard landing and the crash. By using the free-drop table, we showed that the ELT system performed well.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.11
• /
• pp.2677-2685
• /
• 2013

Car running data collected from the vehicle is a native image data and sensing data of it. Hence, it can be used as a set of objective data based on which events that took place outside the car can be analyzed and determined. In this paper, we designed and implemented a emergency situation detection system to sense, store, and analyze signals related to car movements, driver's various operation states, collision pulse, etc when a car collision accident occurs on the actual road by sensing and analyzing the car movements and driver's operation status. The suggested system provides information on the driver's reaction right before the collision, operation state of the vehicle, and physical movement. The collected and analyzed data on vehicle running can be utilized to clarify the cause of a collision accident and to handle it in a just manner. Besides, it can contribute to grasping and correcting wrong driving habits of the driver and to saving.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.65-73
• /
• 2012

Wrist wearable device for the measurement of pulse rate, ECG, and activity during normal daily life, which could be used for the continuous monitoring and remote transmission of acquired data, was developed. Pressure sensor, device attached electrodes, and 3-degree accelerometer were used. Analysis algorithm and firmware program were established for providing diagnostic information for the users. Results of this study, possible for the management of health report and transmission of the results through bluetooth by wearing simple personal wrist device, could be used for the development of portable device in the u-healthcare environment.

• Science of Emotion and Sensibility
• /
• v.18 no.3
• /
• pp.63-70
• /
• 2015

This study identified heart response of participants while listening to sounds which have 1/f fluctuations with exponent ${\alpha}$ gradient. The participants were engaged in emotional stress work. Prior studies related to 1/f fluctuation sound have reported that sound source can alleviate psychological and physiological state of users. Subjects of this study were exposed to sound with three levels of ${\alpha}$ gradient. Heart response of subjects were measured with Photoplethysmography(PPG) sensor simultaneously. The dependent variables of this study were beat per minute(BPM), very low frequency percent of pulse rate variability (VLF percent), the standard deviation of all normal RR intervals (SDNN), and high frequency power(HF power). Subject showed arousal response when exposed to sound with exponent ${\alpha}$ gradient of 3 whereas the sound with exponent ${\alpha}$ gradient of 1 and 2 resulted in relax effect. The characteristic of 1/f fluctuation sounds can be applied to alleviate stress for employers under emotional labor.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.233-238
• /
• 2003

Several types of gamma-ray sensors were constructed by packing different numbers of fibers into aluminum tubes, and tested to detect the $^137Cs$ gamma ray. It has been found from this investigation that tapered fibers can be more efficient to collect the lights produced inside the sensor and transfer them into the transmitting fiber in order to predict the functioning of the tapered fiber, tapered plastic scintillators, composed of polystyrene with minute amount of dPOPOP and PPO or dPBD, were fabricated and tested for the detection of gamma rays from 1.0 1.5 3.0 5.0 ${\mu}Ci$ $^137Cs$ sources, and the pulse hight spectrum and the relationship between the radioactivity and the total counts are analyzed. It has been found from this study that the tapered scintillating optical fiber, if manufactured, can be practically applied to the development of gamma-ray sensors which can be deployed In ${\mu}Ci$-level radiation fields

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.1
• /
• pp.1-10
• /
• 1985

Solar energy has its advantages not to be interruped by anything, which is wing to not only limitlessness in its source but shortness in its wave. Availing of tha advantages, we can look forword to vast allication. This study whose aim is to raise the effectuality of it by means of chasing the source correctly, which is to be acheved by the circularty of sensor. The consequence has been gained by two sensors is amplified and transfered to TTL leveland becomes "INPUT DATA" of INTE 8080CPU. The INTEL 8080CPU whose system is machinated to give cotrol pulse to moter driving circuit has the source and the sensors placed correctly on the basis of the data. DC motor taskes the advantage not to be in need of UP/DOWN counter, which is defferent from stepping motor. The system is composed of light detector, A/C converter, INPUT Interface, INTEL 8080 CPU, OUTPUT Interface, notor driving circiut. We can give correct chase to light experimentally as far as an error is the space of 1.2.ce of 1.2.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.12B
• /
• pp.1236-1243
• /
• 2010

The perimeter defense system was created and its characteristics were evaluated. It was designed to utilize the fiber sensing device, namely OTDR(Optical Time Domain Reflectometer) which has been used for the maintenance of the optical communication network. An OTDR was constituted by a pulse laser with the nature of 1310nm, +15dBm for the observation of 400 meter optical fence. The high-speed 32-bit processor(S3C2440) has applied to MPU(Main Processor Unit) which helps to improve the performance of OTDR algorithms. Consequently, the maximum error was 0.84 meter on the performance test of the 10km monitoring and the pass criteria of ${\pm}1m$ satisfied in all the sections. The alarm delay time was under 3 sec after detecting the disorder. For the case of secondary trespassing after primary trespassing, the optical switch was installed in OTDR to monitor the secondary trespassing and to measure the multi-point detection. Therefore, this paper shows that the detections of secondary trespassing and multi-point is possible by means of optical switch.

• Journal of Digital Contents Society
• /
• v.16 no.3
• /
• pp.457-462
• /
• 2015

Hybrid video call healthcare system that we propose in thesis is a service for powerless people rather than ordinary people. This system is for communication between users and protectors(or volunteers). To reduce the underprivileged through the 'Malbeot Nanumi' is the purpose of the system. Hybrid Health Care System using a video call and temperature/humidity/pulse sensors that we propose in thesis can connect sensors with software, and save p2p connection information for 'Malbeot Nanumi' service by database. And health check data can save locally. Hybrid Health Care System in a Wireless Network Environment is a system that elderly people living alone is to be a conversation. The purpose of this thesis is to develop the software and to design a convenient UI to the user, And increasing consumption of care system by increasing the happiness index and increasing aging population.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.213-216
• /
• 2011

The feasibility study must be conducted for construction of complex for generation of electric power such as items to get permission and grid connection etc. including wind resource to construct a complex for wind power generation. Since wind power can be used by converting only around 20~40% of energy coming in that kinetic energy of wind passes through blades and driving device into electric energy, when constructing a complex, the survey of wind resource takes up the most important part. Data logger used to measure this wind energy are expressed by calculating generally electromotive that is created from a sensor, variable-type, pulse-type signal to be proper for the actual value, and most data loggers have a type without considering geographical features. Besides, in the case of Met mast that is installed to survey the wind resource, since it is installed lower than the hub height of a wind power generator due to permission matters and the economic factors, the height of wind speed by utilizing Deacon equation is compensated to revise this. In this study, a device measuring wind speed was made by using algorithm that is possible to compensate the height of wind speed according to regional features and by applying Deacon equation, and the function of data storage through SD card or RS232 communication was added as well. Besides it's possible to check data more easily with a type of graph by using LCD touch screen for the convenience of users.