• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.307-315
• /
• 1993

A direct draft measurement system was developed based on the swingle tree- the rear component of the single-animal harnessing (or yoking) system . The prototype was made from a tube, on which four strain gages were attached. The pull of the draft animal through the flexible pull chains or ropes causes the beam to bend, The bending strain is sensed by the strain gages and the bridge converts this to a voltage signal. Counterweights keep the tube correctly oriented if the angle of pull changes , while end bearing follow the variations in the angle of pull. Hence, the voltage output is proportional to the draft. the device has highly linear response, acceptable sensitivity negligible error and hysteresis. It is suitable for electronic data acquisition, non-intrusive , easy to attach and detach and is reasonably priced.

• Proceedings of the Korea Multimedia Society Conference
• /
• 1998.04a
• /
• pp.302-307
• /
• 1998

Push 기술은 서버에서 제공하는 정보가 변경되면 클라이언트가 자동으로 다운로드 받아 사용자가 사용할 수 있도록 하는 개념이다. 이는 기존 Pull 기반의 WWW 기술과 비교하여, 사용자들이 원하는 시간에, 원하는 정보를 얻을 수 있도록 하는 혁신적인 정보 전달 방식이다. 본 논문에서는 기존 WWW 기반 원격강의의 단점을 보완하고, 보다 편리한 사용자 위주의 인터페이스를 구현하기 위하여 Pull 방식과 병행하여 Push 방식을 도입한 원격강의를 제안하고 구현하는 것을 목적으로 한다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.222-225
• /
• 2006

Pull-off test is widely used to evaluate bond performance between concrete and FRP composite. However, reliability of experiment result declines due to many difference between test methods of each national standards. This study analyzed problems of various existing test methods for pull-off test and suggested standardized test method. In addition, since tensile strength of concrete is smaller than bond strength of epoxy resin, maximum bond strength of epoxy resin shall be limited within tensile strength of concrete. Alternative testing method, therefore, which decrease FRP adhesion areas than concrete adhesion areas is suggested to widen test range of bond strength in pull-off test. In the experimental results, bond performance can be estimated up to two times of tensile strength of concrete by reducing FRP adhesion areas by 1/3.

• Journal of Information Display
• /
• v.9 no.2
• /
• pp.9-13
• /
• 2008

A novel push-pull voltage converter structure, using a switched capacitor type voltage doubler, is proposed. The circuit is constructed with a two-stage push-pull voltage doubler that has a stable operation with small output ripple. The two-stage voltage doubler creates the output voltage 4Vdd. The high clock signal is cross-coupled to the input of the second stage with the opposite phase to reduce two switching transistors and capacitors. Simulation results verify that even with a reduced number of transistor and capacitor, there is no circuit performance loss. Adding one capacitor and two switching transistors the circuit can be changed to eight times of Vdd maker.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.342-347
• /
• 2004

Excavation nearby the existing structures is being performed vigorously to get the greatest use of land along with fast economic growth in the downtown area. The application of soil nailing system gradually increases because of an advantage of soil nailing system adjacently constructed in the existing structures. In this study, friction resistance by pull-out is considered as main resistance except resistance formed by flexural rigidity of nail observing that resistance of flexural rigidity is about $0{\sim}15\;%$ of whole safety factor according to degree of flexural rigidity in general soil nail wall and application of geosynthetic fiber soil nailing system is evaluated through laboratory tensile strength test and field pull-out test.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1384-1392
• /
• 2002

Single fiber pull-out technique has been commonly used to characterize the mechanical behavior of interface in fiber reinforced composite materials. An improved analysis considering the effects of transversely isotropic properties of fiber and the effects of thermal residual stresses in both radial and axial directions along the fiber/matrix interface is developed for the single fiber pull-out test. Although the stress transfer properties across the interface is not much affected by considering the transversely isotropic properties of fiber, interfacial debonding is notably encouraged by the effect. The interfacial shear stress that plays an important role in interfacial debonding is very much affected by the component of axial thermal residual stress in the bonded region, which can induce a two-way debonding mechanism.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.4
• /
• pp.464-473
• /
• 2003

A method for force-free control is proposed to realize pull-out work by an industrial articulated robot arm. This method achieves not only non-gravity and non-friction motion of an articulated robot arm according to an exerted force but also reflects no change in the structure of the servo controller. Ideal performance of a pull-out work by the force-free control method was assured by means of simulation and experimental studies with a two-degree-of-freedom articulated robot arm.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.2
• /
• pp.102-111
• /
• 1989

In this paper two new non-inverting type BiCMOS drivers are proposed. These are characterized by the use of pMOSFET's in charging the bases of pull-down bipolar transistors. The delay time in pull-up transition of the proposed drivers is 20%-47% shorter than that of the drivers of current using. The proposed drivers use 1-3 fewer MOSFET's in comparison with the drivers of current using.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.198-208
• /
• 1995

BiCMOS circuit consist of CMOS part which constructs logic function, and bipolar part which drives output load. Test to detect stuck-open faults in BiCMOS circuit is important, since these faults do sequential behavior and are represented as transition faults. In this paper, proposes a method for efficiently detecting transistor stuck-open faults in BiCMOS circuit by transforming them into slow-to=rise transition and slow-to-fall transition. In proposed method, BiCMOS circuit is transformed into equivalent gate-level circuit by dividing it into pull-up part which make output 1, and pull-down part which make output 0. Stuck-open faults in transistor are modelled as transition fault in input line of gate level circuit which is transformed from given circuit. Faults are detceted by using pull-up part gate level circuit when expected value is '01', or using pull-down part gate level circuit when expected value is '10'. By this method, transistor stuck-open faults in BiCMOS circuit are easily detected using conventional gate level test generation algorithm for transition fault.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.647-652
• /
• 2015

Pull-in voltage model of nano-electro-mechanical system with graphene is investigated for the device optimization. In the pull in voltage model, thickness of graphene layer is assumed to be uniform in vertical and lateral direction. Finite element analysis simulation has verified the feasibility of the suggested model. From the suggested model, pull-in voltage change with graphene thickness and cantilever length can be estimated. Maximum induced stress and graphene thickness have a reciprocal relationship.