• 한국전자거래학회:학술대회논문집
• /
• 한국전자거래학회 1999년도 학술대회지 vol.1
• /
• pp.95-108
• /
• 1999

The purpose of this study is to find the diversification of the methodology of KM (knowledge management) Benchmarking which has been developed rapidly as a new managing paradigm all over the world for the 21th century. In particular, at the point of that it has been going to be inevitable for domestic companies to adopt and utilize a knowledge management system as the pending assignment for surviving in the 21th century, this study thus can enable them to support an adoption of KM and suggest directions for companies. Therefore, the successful cases of KM adoption all through the world have been analyzed by this study with the classifications of the industrial fields, work-flows from the view point of learning organizations and information technologies. As a result, the KM type bearing the specific of the respective industry has not been unrolled, and the common element in the analysis of work-flows has been found. Based on the result, it is desirable for the companies to adapt KM, extracting necessary work field for KM. Consequently speaking, they need to benchmark and adopt the KM methodology based on the extracted results.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(I)
• /
• pp.408-413
• /
• 2002

From the moment that electricity is applied to a relay, a wheel turned, or a valve opened, the process leading to the need for maintenance begins, The uninitiated will tell you that the Maintenance man is someone who repairs something when it has gone wrong. Unfortunately, in any large engineering concern, such as a railway, it is not possible to work on the principle that only when something breaks down should it get any attention. The failure of one contact, diode or bearing could well stop not only the assembly of which it is a part, but the flow line or process, with loss of revenue, and clientele, and often with effects on the safety of both staff and the traveling public. So, we have to establish the reliable and cost-effective maintenance system to resolve these problems.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.1364-1368
• /
• 2006

By the countermeasure which is caused by with railroad station ground settlement it applied a CGS in each independent foundation. The effectiveness of the ground improvement and the bearing capacity of the compaction pile has been verified by the Cone Penetration Test(CPT) and Load Test. Test result show that penetration resistance and the cone friction force increased a lot and settlement 13.475mm as the standard settlement 40.0mm appeared at below. Also uniaxial compression test result $278kg/cm^2$ as the standard $150kg/cm^2$ appeared far a lot.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.558-564
• /
• 2006

When vehicles pass the connection between the bridge and earthwork, the difference of both sections' stiffness produces an increasing wheelload. As a consequence, it results in the excessive vibration of vehicles and the damage of bearing system. In general, steel plate girder railway bridges without ballast track have larger stiffness than the bridge with ballast, and produces larger impulse on the bridge superstructure. Thus, it is necessary to reduce the differences of both stiffness. This study presents parametric studies on the behavior of plate girder bridges and their tracks by means of various stiffnesses and the length of approach zone. The results of numerical study showed that the smaller the stiffness of both sides and the longer the length of approach zone, the variation of wheelload becomes smaller. Hence, it gives less burden into the plate girder bridges and their tracks. It is expected that the results of parametric study can be used as a preliminary data for the determination of economical length on the approach zone and the stiffness of both sides.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.189-196
• /
• 2002

According to the Korean Design Code for port and harbor facilaties, bearing capacity of rubble mound under eccentric and inclined load is calculated by the simplified Bishop method, and strength parameters are recommended to be c=0.2kg/$\textrm{cm}^2$ and ø=35$^{\circ}$for standard rubble if the compressive strength of parent rock is greater than 300kg/$\textrm{cm}^2$, quoting from research results by Jun-ichi Mizukami(1991), But this facts have never been certified in Korea because there was not large-scale triaxial test apparatus until 2000 in Korea. Firstly in Korea, the large-scale triaxial test (sample diameter, 30cm and height, 60cm) on the rubble originated from porous basalt rock in North-Cheju was accomplished. Then strength parameters for basalt rubble produced in North-Cheju are recommended to be c=0.3kg/$\textrm{cm}^2$ and ø=36$^{\circ}$if the compressive strength of parent rock is greater than 400kg/$\textrm{cm}^2$.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.549-556
• /
• 2002

Geotextile tubes hydraulically or mechanically filled with dredged materials have been applied in hydraulic and coastal engineering in recent years(shore protection structure, detached breakwater, groins and jetty). It can also be used to isolate contaminated material from harbor, detention basin dredging, and to use this unit as dikes for reclamation work. Recently, new preliminary design criteria supported by model and prototype tests, and some stability analysis calculations have been studied. The stability analysis of geotextile tube is composed geotechnical and hydrodynamic analysis. The stability check points are sliding failure, overturning, bearing capacity failure against the wave attack. In this paper presented the construction procedure and in-situ measurement(properties of filling material, effective height variation, stress variation at geotextile tube bottom) of geotextile tube at Young-Jin Bay and stability analysis by theoretical method and hydraulic model tests

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.461-464
• /
• 2004

External prestressing method is the most papular method to strengthen concrete structures. The key parts of external prestressing method is an anchoring device which holds the prestressing cables. The most popular anchoring devices is an end bearing type, which has to be welded at site to assamble the anchor. The welding at site has a significant Quality problem. In this paper, new anchoring system has been developed, which needs no site welding. A design method for the new anchor has been proposed and developed to optimize the anchoring system. The developed anchors are very efficient, small, and compact, which have two types, one for abutment section and the other one for pier section. The anchors are expected to be used very widely, because of its convinience.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.101-104
• /
• 2006

In the past study, the fragility curve for the evaluation of earthquake resistance and earthquake-related damage of concrete bearing wall structures were studied. The fragility curve represents the probability of being in or exceeding a given damage state such as Slight, Moderate, Extensive or Complete structural damage state, and is defined as a cumulative lognormal distribution. Each fragility curve is characterized by median and lognormal standard deviation values. We performed parametric pushover analysis for typical 12 and 24 stories apartment buildings. Based on the results, the fragility curves of concrete wall structures were standardized. Using the fragility curve, engineers can directly evaluate the probability of a damage state to a spectral displacement of interest.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1998년도 추계학술대회 학술발표 논문집
• /
• pp.156-165
• /
• 1998

This paper proposes a systematic design methodology for the Takagi-Sugeno(TS) model based fuzzy control system with guaranteed stability and additional constraints on the closed-loop pole location. These combined two objectives are formulated as a system of LMIs(Linear Matrix Inequalities). Since LMIs intrinsically reflect constraints, they tend to offer more flexibility for combining various constraints on the closed-loop system. To demonstrate the usefulness of the proposed design methodology it is applied to the requlation problem of a nonlinear magnetic bearing system. Simulation results show that the proposed LMI-based design methodology yields not only maximized stability boundary but also the desired transient responses.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.291-300
• /
• 1999

Currently under development is an airborne auxiliary power unit with 100 Kw equivalent power, which is composed of a centrifugal compressor, a reverse annular combustor, and a radial turbine. Air-foil bearings are used in this power unit to eliminate the oil supplying system, which can reduce the system complexity and weight. The high speed generator is adopted as an electric power generation and engine starting system, which can also eliminate the reduction gear system. Not only electric power but also pneumatic power is provided by bleeding the compressed air This power unit is aimed for the multi-purpose use such as a primary power unit In the army weapon system, an auxiliary power and environmental control unit in a next-generation tank, and a smoke generating unit.