• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.4
• /
• pp.24-31
• /
• 1988

The Upper Bound Solution has been used to investigate the effect of the various parameters on the floating-plug tube-drawing precess. A kinematically admissible velocity field considering the change of the tube thickness is proposed for the deformation process. Taking into account the position of the plug in the deforming region, shear energy at entrance and exit, friction energy on contact area, homogeneous energy are calculated. The theoretical values in proposed velocity field are good agreement with experimental values, It is investigated that the tube thickness in the deforming region is changed slightly toward minimization of deforming energy and then the drawing stress in lower than the crawing stress in the velocity field that the tube thickness is uniform.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.109-116
• /
• 2002

The solution of the aircraft wing spar cross-section area optimization problem is obtained by the response surface method. The object function of the problem is wing total weight, design variables are spar cross-section areas, constraints are the conditions that the stresses at the each spar is less than the allowable stress. D-Optimal condition is utilized to obtain the experimental points to construct the response surfaces. D-Optimal experimental points are obtained by the commercial software "Deign-Expert". Response values for the object function and constraints for each experimental point are calculated by the NASTRAN. Response surfaces for object function and constraints are approximated from the response values by the least square method. The optimization solution is obtained by the DOT for the response surfaces of object function and constraints. The optimization results obtained from the response surface are compared with the results obtained by the NASTRAN SOL200.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.599-600
• /
• 2006

In order to promptly cope with the various requirements of consumers, the environment of product development is being globalized in manufacturing industrials. For this reason, it is necessary to build up an efficient collaborative system for communication between remote area designers. Specially, while Internet and information technologies were merged with the manufacturing or business process, the research for collaborative system has become an important issue. Therefore, we propose a Web-based Engineering Collaboration Framework using SPS(SharePoint Portal Server) which is an enterprise business solution that integrates information from various system into one solution through single sign-on and enterprise application integration capabilities, with flexible deployment options and management tool. Through a Web-based Engineering Collaboration Framework, designers can share knowledge assets and have a remote conference with others via web.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.114-121
• /
• 1997

In this paper, the automated initial process planning for 3-axis NC machining of sculptured surfaces is persented. The solution algorithms determining three process planning functions, i.e. machining feasibility, setup orientation and feasible machine selection are developed. The machining feasibility is determined by means of BSM(Binary Spherical Map) which derives its solution quickly in algebraic form, and the setup orientation is determined so that the cutting force is minimized. Finally, the feasible machine is determined by computing the minimum motion ranges of each control axisl. The developed algorithms are tested by numerical simulations, convincing they can by readily implemented on the CAD/CAM system as a process planner.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.134-139
• /
• 2007

We report the suspension of individual multi-walled carbon nanotubes (MWNTs) from the bottom substrate using deep trench electrodes that were fabricated using optical lithography. During drying of the solution in dielectrophoretic assembly, the capillary force pulls the MWNT toward the bottom substrate, and it then remains as a deformed structure adhering to the bottom substrate after the solution has dried out. Small-diameter MWNTs cannot be suspended using thin electrodes with large gaps, but large-diameter MWNTs can be suspended using thicker electrodes. We present the statistical experimental results for successful suspension, as well as the feasible conditions for a MWNT suspension based on a theoretical approach.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.240-240
• /
• 2003

V-노치 균열에서 열하중이 작용하는 경우는 비제차형 경계조건의 문제가 되고, 이 조건에 대한 방정식의 일반해를 구하기 위해서 재차형 연립방정식에 대한 일반해(Homogeneous solution)와 비제차형 연립방정식에 대한 특수해(Particular solution)의 두 가지 해를 구할 수 있다. 이들 해는 V-노치 균열에 대한 고유치가 되고 이 고유치가 중복근을 가지게 되는 경우에는 로그항(1n[r])이 나타나게 되고 이 항에 의해서 응력을 무한대로 발산시키므로 이를 대수응력특이성이라 한다. 열하중이 작용할 때 대수응력특이성을 나타내는 로그항의 계수가 영(0)이 되어 대수응력특이성이 사라지게 되므로 V-노치 선단에서의 응력특이성은 고유치와 그에 대한 고유벡터에 의해 결정된다. 본 논문에서는 비정상상태 열하중이 가해지는 등방성 이종재료 내의 V-노치 균열문제에서 패기 각도와 이종재료의 기계적 성질에 의해 결정되는 응력특이성지수를 구하고 이에 대한 응력강도계수를 유한요소해석 프로그램인 ANSYS와 상반일 경로 적분법(RWCIM)을 이용하여 구하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.1
• /
• pp.59-63
• /
• 2017

We present a multi-sample array device based on a pneumatic system. Solenoid valves were used to control a micro valve in a pneumatic system. The use of a compressor together with a vacuum pump ensured that one outlet could supply both compression and vacuum pressure. The multi-sample array device was fabricated using conventional photolithography and PDMS casting. The device was composed of a multiplexer, sample array, and rinsing. The multiplexer could control four sample solutions injecting into the sample array chamber. Sample solution not arrayed was removed by DI-water from the rinsing inlet. To prevent trapping of microbubbles in the channel during injection of sample solution into the device, surfactant was added in PDMS solution to serve as a hydrophilic surface treatment. As a result, the device could be used as a sample array for 64 cases, using four samples and three columns of three chambers.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.57-68
• /
• 1995

A general procedure for the numerical solution of coupled, nonlinear, differential two-point boundary-value problems, solutions of which are crucial to the controller design, has been developed and demonstrated. A fixed-end-points, free-terminal-time, optimal-control problem, which is derived from Pontryagin's Maximum Principle, is solved by an extension of Davidenko's method, a differential form of Newton's method, for algebraic root finding. By a discretization process like finite differences, the differential equations are converted to a nonlinear algebraic system. Davidenko's method reconverts this into a pseudo-time-dependent set of implicitly coupled ODEs suitable for solution by modern, high-performance solvers. Another important advantage of Davidenko's method related to the time-optimal problem is that the terminal time can be computed by treating this unkown as an additional variable and sup- plying the Hamiltonian at the terminal time as an additional equation. Davidenko's method uas used to produce optimal trajectories of a single-degree-of-freedom problem. This numerical method provides switching times for open-loop control, minimized terminal time and optimal input torque sequences. This numerical technique could easily be adapted to the multi-point boundary-value problems.

• Annals of Geriatric Medicine and Research
• /
• v.22 no.4
• /
• pp.157-158
• /
• 2018

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.4
• /
• pp.15-23
• /
• 2002

With the development of a laser scanner of high precision and increased speed, reverse engineering becomes a key approach to reduce the time for the development of new products. But the modeling process is not so automated enough until now. Modeling in real workshops is usually performed by the experienced operators and it requires a skillful technique to get the resultant surface of high quality and precision. In this paper, a systematic solution is proposed to automate the free-form surface generation from the measured point data. Compatibility is imposed to the measured point data during input curve generation. And the compatibility of cross-sectional curve is also considered for the loft surface generation. The data in each step is produced in IGES file format to make an easy interface to other CAD/CAM software without any further data manipulation.