• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.6
• /
• pp.43-49
• /
• 1997

Tungsten poycide has studied gate oxide reliability and dielectric strength charactristics as the composition of gate electrode which applied submicron on CMOS and MOS device for optimizing gate electrode resistivity. The gate oxide reliability has been tested using the TDDB(time dependent dielectric breakdwon) and SCTDDB (stepped current TDDB) and corelation between polysilicon and WSi$_{2}$ layer. iN the case of high intrinsic reliability and good breakdown chracteristics on polysilicon, confirmed that tungsten polycide layer is a better reliabilify properities than polysilicon layer. Also, hole trap is detected on the polysilicon structure meanwhile electron trap is detected on polycide structure. In the case of electron trap, the WSi$_{2}$ layer is larger interface trap genration than polysilicon on large POCL$_{3}$ doping time and high POCL$_{3}$ doping temperature condition. WSi$_{2}$ layer's leakage current is less than 1 order and dielectric strength is a larger than 2MV/cm.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.1-6
• /
• 2000

This article presents the experiments and considerations possible about gate etching in polysilicon when oxygen gas is added in chamber, We propose the novel study with optical emission spectroscopy in polysilicon etching. It is shown that added oxygen gases play an important role in enhencement of density in chlorine gases as a scavenger of silicon from SiCl$\_$x/. And a small amount of Si-O bonds are deposited and then the deposited thin film protect silicon dioxyde against reaction chlorine with silicon in SiO$_2$. Consequently, we can improve the selectivity of polysilicon the silicon dioxide, which is clearly explained in this model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.2
• /
• pp.113-117
• /
• 2007

We have investigated the effects of doping concentration in polysilicon floating gate on the endurance characteristics of the EEPROM cell haying the structure of spacer select transistor. Several samples were prepared with different implantation conditions of phosphorus for the floating gate. Results show the dependence of doping concentration in polysilicon floating gate on performance of EEPROM cell from the floating gate engineering point of view. All of the samples were endured up to half million programming/erasing cycle. However, the best $program-{\Delta}V_{T}$ characteristic was obtained in the cell doped at the dose of $1{\times}10^{15}/cm^{2}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.1
• /
• pp.99-102
• /
• 2002

Pinholes on the thermally grown oxide, which is called gate oxide, on silicon substrate under polysilicon layer are found and its mechanism is analyzed in this paper. The oxide under a polysilicon layer is broken during the plasma etching process of other polysilicon layer. Both polysilicon layers are separated with 0.8${\mu}{\textrm}{m}$ thick oxide deposited by CVD (Chemical Vapor Deposition). Since broken oxide points are found scattered around an arc occurrence point, it is assumed that an extremely high electric field generated near the arc occurrence point makes the gate oxide broken. 1'he arc occurrence point has been observed on the alignment key and is the mark of low yield. It is found that any arc occurrence can cause chips to fail by breaking the gate oxide, even if are occurrence points are found on scribeline.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.358-361
• /
• 2002

Self-aligned MOSFETS using a polysilicon gate are widely fabricated in silicon technology. The polysilicon layer acts as a mask for the source and drain implants and does as gate electrode in the final product. However, the usage of polysilicon gate as a self-aligned mask is restricted in fabricating SiC MOSFETS since the following processes such as dopant activation, ohmic contacts are done at the very high temperature to attack the stability of the polysilicon layer. A metal instead of polysilicon can be used as a gate material and even can be used for ohmic contact to source region of SiC MOSFETS, which may reduce the number of the fabrication processes. Co-formation process of metal-source/drain ohmic contact and gate has been examined in the 4H-SiC based vertical power MOSFET At low bias region (<20V), increment of leakage current after RTA was detected. However, the amount of leakage current increment was less than a few tens of ph. The interface trap densities calculated from high-low frequency C-V curves do not show any difference between w/ RTA and w/o RTA. From the C-V characteristic curves, equivalent oxide thickness was calculated. The calculated thickness was 55 and 62nm for w/o RTA and w/ RTA, respectively. During the annealing, oxidation and silicidation of Ni can be occurred. Even though refractory nature of Ni, 950$^{\circ}C$ is high enough to oxidize it. Ni reacts with silicon and oxygen from SiO$_2$ 1ayer and form Ni-silicide and Ni-oxide, respectively. These extra layers result in the change of capacitance of whole oxide layer and the leakage current

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.209-213
• /
• 2007

The MOS gate capacitance model presented here is determined by directly solving the coupled Poisson equations on the poly and silicon sides, and includes the polysilicon (poly) gate depletion effect. Our compact gate capacitance model exhibits an excellent fit with measured data and parameter values extracted from data are physically acceptable. The data are collected from 0.5, 0.35, 0.25 and $0.18{\mu}m$ CMOS technologies.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.12
• /
• pp.53-58
• /
• 1991

Hot-carrier induced degradation has been studied for the BF$_2$ ion-implanted surface-channel LDD(P$^{+}$ polysilicon gate) PMOSFET in comparison to the buried-channel structure(N$^{+}$ polysilicon gate) PMOSFET. The conditions for maximum degradation better correlated to I$_{g}$ than I$_{sub}$ for both PMOSFET's. Due to the use of LDD structure on SC-PMOSFET, the substrate current for SC-PMOSFET was shown to be smaller than that of BC-PMOSFET. The gate current was smaller as well, due to the gate material work-function difference between p$^{+}$ and n$^{+}$ polysilicon gates. From the results, it was shown that the surface-channel LDD PMOSFET is more resistant to short channel effect than the buried-channel PMOSFET.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.490-495
• /
• 1999

In 0.18 $\mu \textrm m$ LOGIC device, the etch rate of NMOS polysilicons is different from that of PMOS polysilicons due to the state of polysilicon to manufacture gate line. To control the etch profile, we tested the ratio of $Cl_2$/HBr gas and the total chamber pressure, and also we reduced Back He pressure to get the vertical profile. In the case of manufacturing the gate photoresist line, we used Bottom Anti-Reflective Coating (BARC) to protect refrection of light. As a result we found that $CF_4O_2$ gas is good to etch BARC, because of high selectivity and good photoresist line profile after etching BARC. in the results of the characterization of plasma damage to the antenna effect of gate oxide, NO type thin film(growing gate oxide in 0, ambient followed by an NO anneal) is better than wet type thin film(growing gate oxide in $0_2+H_2$ ambient).

• Journal of Electrical Engineering and information Science
• /
• v.2 no.3
• /
• pp.132-138
• /
• 1997

Electrical characteristics of split-gate flash EEPROM with triple polysilicon is investigated in terms of effects of floating gate and offset gate. In order to search for t the effects of offset gate on programming characteristics, threshold voltage and drain current are studied with variation of control gate voltage. The programming process is believed to depend on vertical and horizontal electric field as well as offset gate length. The erase and program threshold voltage are found to be almost constant with variation of control gate voltage above 12V, while endurance test indicates degradation of program threshold voltage. With increase of offset gate length, program threshold voltage becomes smaller and the drain source voltage just after program under constant control gate voltage becomes higher.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.2
• /
• pp.261-266
• /
• 1998

This paper describes the fabrication and characterization of dual-polysilicon gated surface channel 0.1$\mu\textrm{m}$ CMOSFETs using BF2 and arsenic as channel dopants. We have used and LDD structure and 40${\AA}$ gate oxide as an insulator. To suppress short channel effects down to 0.1$\mu\textrm{m}$ channel length, shallow source/drain extensions implemented by low energy implantation and SSR(Super Steep Retrograde) channel structure were used. The threshold voltages of fabricated CMOSFETs are 0.6V. The maximum transconductance of nMOSFET is 315${\mu}$S/$\mu\textrm{m}$, and that of pMOSFET is 156 ${\mu}$S/$\mu\textrm{m}$. The drain saturation current of 418 ${\mu}$A/$\mu\textrm{m}$, 187${\mu}$A/$\mu\textrm{m}$ are obtained. Subthreshold swing is 85mV/dec and 88mV/dec, respectively. DIBL(Drain Induced Barrier Lowering) is below 100mV. In the device with 2000${\AA}$ thick gate polysilicon, depletion in polysilicon near the gate oxide results in an increase of equivalent gate oxide thickness and degradation of device characteristics. The gate delay time is measured to be 336psec at operation voltage of 2V.