• 한국항공우주학회지
• /
• 제35권4호
• /
• pp.302-307
• /
• 2007

본 연구에서는 이온성 폴리머-금속 복합재료 (IPMC) 작동기를 사용한 플랩 밸브 마이크로 펌프의 설계, 제작 및 실험적 특성 규명을 수행하였다. 나피온/실리케이트 층과 나피온/실리카 나노복합재료를 기반으로 한 다층형 IPMC를 마이크로 펌프의 작동층으로 사용하였다. 마이크로 펌프의 핵심 요소인 IPMC 다이아프램의 주위를 유연한 폴리디메틸실옥산(PDMS)을 사용하여 지지하도록 함으로써 상당히 큰 작동 변위를 내도록 설계하였다. 이렇게 개발된 마이크로 펌프의 크기는 $20{\times}20{\times}5$ ${mm}^3$ 이고, 최대 유량은 760 l/min, 최대 배압은 1.5 kPa이었다. 본 연구에서 개발한 마이크로 펌프는 간단하고 효율적인 설계를 수행하여 제작이 용이할 뿐 아니라, 동작 전압이 1-3V라는 장점이 있다.

• 대한기계학회논문집A
• /
• 제36권5호
• /
• pp.475-479
• /
• 2012

본 논문은 고차가지구조 폴리머인 AEO3000 를 이용한 UV 광경화 성형 공정을 제안하고자 한다. 이는 기존의 바이오칩 제작에 사용되는 PDMS 보다 경도가 높아 금속 전극 형성이 용이하고 제작 공정이 빠르다는 장점을 갖는다. AEO3000 을 이용하여 본 연구에서는 4 개의 소자를 전기적 유체적으로 연결할 수 있는 전기유체 통합벤치를 제작하고 미소유체 혼합소자와 세포분리소자를 연결, 본 소재와 공정이 바이오칩에 적용될 수 있음을 검증하였다. 전기 유체적 특성 분석 결과 전기적 접촉 저항은 $0.75{\pm}0.44{\Omega}$으로 충분히 작은 값을 보였으며, 유체 접속의 압력 저하는 8.3kPa로 기존의 튜브 연결 방법 대비 39.3% 개선된 값을 보였다. 통합벤치에 접속된 소자에 활성 및 비활성 효모를 주입하여 순차적인 혼합 및 재분리를 성공적으로 구현함으로써 본 소자에 적용된 AEO3000 및 UV 광경화 공정이 생체시료의 처리에 적용될 수 있음을 실험적으로 검증하였다. 이는 바이오 의료 분야에 적용 가능한 생체 친화적 소재의 고속 생산에 응용될 수 있다.

• Bulletin of the Korean Chemical Society
• /
• 제32권4호
• /
• pp.1298-1302
• /
• 2011

This study describes the development of an electrochemical array immunochip for the detection of IgG. Interdigitated immunochip platforms were fabricated by sputtering gold on a glass wafer by using MEMS process and then were coated with Eudragit S100, an enteric polymer, forming an insulating layer over the working area of immunochips. The breakdown of the polymer layer was exemplified by the catalytic action of urease which, in the presence of urea, caused an alkaline pH change. This subsequently caused an increase of the double layer capacitance of the underlying electrode. Used in conjunction with a competitive immunoassay format, this allowed the ratio of initial to final electrode capacitance to be directly linked with the concentration of analyte, i.e. IgG. Responses to IgG could be detected at IgG concentration as low as $250\;ngmL^{-1}$ and showed good linearity up to IgG concentration as high as $20\;{\mu}gmL^{-1}$.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.267-272
• /
• 2002

Nano adhesion between SPM(scanning probe microscope) tips and DDPO$_4$(octadecylphosphoric acid ester.) and ODPO$_4$(octadecylphosphoric acid ester) SAM(self-assembled monolayer.) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes with the applied normal load. DDPO$_4$ and ODPO$_4$ SAM were formed on Ti and TiOx surfaces. Ti and TiOx were coated on the Si wafer by ion sputtering. Adhesion and friction of DDPO$_4$ and ODPO$_4$ SAM surfaces were compared with those of OTS(octadecyltrichlorosilane) SAM and DLC surfaces. DDPO$_4$ and ODPO$_4$ SAM converted the Ti and TiOx surfaces to be hydrophobic. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare surfaces. Work of adhesion was also discussed to explain how the surface was converted into hydrophobic Results also showed that tribological characteristics of DDPO$_4$ and ODPO$_4$ SAM had good properties in the adhesion, friction, wetting angle and work of adhesion. DDPO$_4$ and ODPO$_4$ SAM could be one of the candidates for the bio-MEMS elements.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.69-69
• /
• 2003

최근 trench capacitor, isolation trench, micro-electromechanical system(MEMS), micro-opto-electromechanical system(MOEMS)등의 다양한 기술에 적용될 고종횡비(HAR) 실리콘 식각기술연구가 진행되어 지고 있다. 이는 기존의 습식식각시 발생하는 결정방향에 따른 식각률의 차이에 관한 문제와 standard reactive ion etching(RIE) 에서의 낮은 종횡비와 식각률에 기인한 문제점들을 개선하기 위해 고밀도 플라즈마를 이용한 건식식각 장비를 사용하여 고종횡비(depth/width), 높은 식각률을 가지는 이방성 트랜치 구조를 얻는 것이다. 초기에는 주로 HBr chemistry를 이용한 연구가 진행되었는데 이는 식각률이 낮고 많은양의 식각부산물이 챔버와 시편에 재증착되는 문제가 발생하였다. 또한 SF6 chemistry의 사용을 통해 식각률의 향상은 가져왔지만 화학적 식각에 기인한 local bowing과 같은 이방성 식각의 문제점들로 인해 최근까지 CHF3, C2F6, C4F8, CF4등의 첨가가스를 이용하여 측벽에 Polymer layer의 식각보호막을 형성시켜 이방성 구조를 얻는 multi_step 공정이 일반화 되었다. 이에 본 연구에서는 SF6 chemistry와 소량의 02/HBr의 첨가가스를 이용한 single_step 공정을 통해 공정의 간소화 및 식각 프로파일을 개선하여 최적의 HAR 실리콘 식각공정 조건을 확보하고자 하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.892-895
• /
• 2003

This paper describes on RIE(Reactive Ion Etching) characteristics of 3C-SiC(Silicon Carbide) grown on Si(100) wafers. During RIE of 3C-SiC films in this work, $CHF_3$ gas is used to form of polymer as a side wall for excellent anisotropy etching. From this process, etch rates are obtained a $60{\sim}980{\AA}/min$ by various conditions such as $CHF_3$ gas flux, $O_2$ addition ratio, RF power and electrode distance. Also, approximately $40^{\circ}$ mesa structures are successfully formed at 100 mTorr $CHF_3$ gas flow ratio, 200 W RF power and 30 mm electrode distance. Moreover, vertical side wall is fabricated by anisotropy etching with 50% $O_2$ addition ratio and 25 mm electrode distance. Therefore, RIE of 3C-SiC films using $CHF_3$ could be applicable as fabrication process technology for high-temperature 3C-SiC MEMS applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제6권4호
• /
• pp.293-298
• /
• 2006

Thermopiezoelectric method, using poly silicon heater and a piezoelectric sensor, was proposed for writing and reading in a probe based data storage system. Resistively heated tip writes data bits while scanning over a polymer media and piezoelectric sensor reads data bits from the self-generated charges induced by the deflection of the cantilever. 34${\times}$34 array of thermopiezoelectric nitride cantilevers were fabricated by a single step wafer level transfer method. We analyzed the noise level of the charge amplifier and measured the noise signal. With the sensor and the charge amplifier 20mn of deflection could be detected at a frequency of 10KHz. Reading signal was obtained from the cantilever array and the sensitivity was calculated.

• 한국정밀공학회지
• /
• 제24권5호
• /
• pp.97-103
• /
• 2007

A novel selective metallization process to fabricate the fine conductive line based on inkjet printing has been investigated. Recently, Inkjet printing has been widely used in flat panel display, electronic circuits, biochips and bioMEMS because direct inkjet printing is an alternative and cost-effective technology for patterning and fabricating objects directly from design without masks. The photosensitive etching resist used in this process is an organic polymer which becomes solidified when exposed to ultraviolet lights and has high viscosity at ambient temperature. A piezoelectric-driven inkjet printhead is used to dispense 20-30 ${\mu}m$ diameter droplets onto the copper substrate to prevent subsequent etching. Repeatability of circuitry fabrication is closely related to the formation of steady droplets, adhesion between etching resist and copper substrate. Therefore, the ability to form small and stable droplets and surface topography of the copper surface and chemical attack must be taken into consideration for fine and precise patterns. In this study, factors affecting the pattern formation such as adhesion strength, etching mechanism, UV curing have been investigated. As a result, microscale copper patterns with tens of urn high have been fabricated.

• 한국정밀공학회지
• /
• 제31권5호
• /
• pp.389-394
• /
• 2014

In this paper, we report a new manufacturing method for friction reduction using micro-AAJ (abrasive air-jet) machining. AAJ machining employs compressed air to accelerate a jet of high-speed particles to mechanically machine features, including micro-channels and micro-holes, into glass, metal, or polymer substrates for use in microfluidics, MEMS (micro electromechanical systems). And we introduce the micro-AAJ machining system, which consists of a micro-AAJ nozzle and a five-axis positioning system. Various micro-AAJ nozzles can be used, depending on the required surface structure, and three-dimensional machining is possible. We machined samples under six different conditions and describe machining results obtained while using it. We also measured the coefficient of friction of micro-textured surfaces. We report the coefficient of friction of micro-textured surfaces patterned using micro-AAJ machining for engine piston ring.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2002년도 정기총회 및 추계학술연구발표회
• /
• pp.54-55
• /
• 2002

The fabrication, characterization and manipulation of nanoparticle system brings together physics, chemistry, materials science and biology in an unprecedented way. Phenomena occurring in such systems are fundamental to the workings of electronic devices, but also to living organisms. The ability to fabricate the surface of nanoparticles Is essential in the further development of functional devices that incorporate nanoscale features. Even more essential is the ability to introduce a wide range of chemical and materials flexibility into these structures to build up more complex nanostructures that can ultimately rival biological nanosystems. In this respect, polymers are potentially ideal nanoscale building blocks because of their length scale, well-defined architecture, controlled synthesis, ease of processing and wide range of chemical functionality that can be incorporated. In this presentation, we will look at a number of promising polymer-based nanoparticle fabrication strategies that have been developed recently, with an emphasis on those techniques that incorporate nanostructured polymeric particles into electronic devices or biomedical applications. And functional nanoparticles deliberately designed using several powerful process methods and their application will be discussed. Nanostructured nanoparticles, what we called, implies dispersed colloids with the size ranged from several nanometers to hundreds of nanometer. They have extremely large surface area, thus it is very important to control the morphology or surface functionality fitted for adequate objectives and properties. Their properties should be controlled for various kind of bio-related technologies, such as immunomagnetic cell separation, drug delivery systems, labeling and identification of lymphocyte populations, extracorporeal and hemoperfusion systems, etc. Well-defined polymeric nanoparticles can be considered as smart bomb or MEMS.