• 전기화학회지
• /
• 제14권1호
• /
• pp.50-55
• /
• 2011

Pt/C 촉매 (20, 40 wt% Pt/C)를 사용하여 고분자 전해질 연료전지의 MEA를 제조하고 각각의 촉매에서 최적의 나피온 이오노머 함량을 알아보았다. 나피온 함량에 따른 MEA의 전기화학적인 성능변화는 단위전지 성능평가, electrochemical impedance spectroscopy (EIS), cyclic voltammetry(CV)을 통해서 분석하였다. 나피온의 함량에 따라 전지의 활성화 분극, 옴 저항, 물질전달 저항 등의 변화가 나타났다. 이는 전극의 촉매층 내에서 발생되는 전기/이온 전도도 사이의 'trade-off'와 물질전달(물 배출과 반응가스 확산)에 의한 것이며, 대부분 활성화 분극과 물질전달 저항의 변화로 나타났다. 20 wt% Pt/C와 40 wt% Pt/C 촉매에서 최적의 나피온 함량은 각각 35 wt%와 20 wt%로 나타났다. 이는 Pt 중량비에 따른 Pt 입자간의 거리 및 촉매의 비표면적의 차이 때문에 나타난 결과이며 서로 다른 나피온 함량에서 최적의 삼상계면이 형성되는 것으로 판단된다.

• 전자공학회논문지SC
• /
• 제46권5호
• /
• pp.38-43
• /
• 2009

본 논문에서는 자기 벡터 포텐셜 해석을 통해 3-코일 구조를 갖는 금속 검출기 헤드가 수신 코일에 미치는 유도 전압을 구하고, 금속 물체의 특성이 송신 코일의 임피던스에 미치는 영향을 유도하였다. 이러한 해석을 통하여 최적의 검출 성능을 위한 송신 코일과 수신 코일 간의 거리를 구하였고, 최대 유도 전압을 출력하는 금속의 위치를 유도하였다. 또한 기존의 수식과 비교하여 본 논문의 자기 벡터 포텐셜 해석에 대한 타당성을 입증하였다.

• 전기학회논문지
• /
• 제60권1호
• /
• pp.100-104
• /
• 2011

In this work, an optimum condition of electrolytes preparation for photovoltaic cells application was investigated experimentally in terms of impedance and conversion efficiency of the cells. 3-methoxyppropionitrie and redox pairs with LiI and $I_2$ were used as stable solvents for fabrication of electrolyte. Efficiency comparison of the prepared cells carried out for various additives and ionic liquids. From the results, there was an optimum concentration (about 0.3 M) of ionic liquids for efficient cell fabrication. For case of electrolyte using single DMAp additive, the maximum conversion efficiency of the cell was 6.4%($V_{oc}$: 0.78V, $J_{sc}$: 14.4 mA/$cm^2$, ff: 0.57). For case of electrolyte using both DMAp and CEMim additives, the maximum conversion efficiency of the cell was 7.2%($V_{oc}$: 0.79V, $J_{sc}$: 16 mA/$cm^2$, ff: 0.57). From the result of electrochemical impedance measurement, both Z1 and Z3 values of binary additives-based cell decreased compared to those of single additive-based. This is due to the decreased in internal and charge transfer resistivities of the cells.

• 한국통신학회논문지
• /
• 제25권5B호
• /
• pp.985-991
• /
• 2000

본 논문에서는 인덕터의 면적을 극소화시키고 인덕턴스와 Q값을 극대화시키기 위한 최적구조의 2GHz 자성박막 인덕터를 설계하고 제작하였다. Eddy-current 표피효과를 위해서 Co90Fe10와 SiO2의 multilayer를 사용하고, multilayer를 적용한 새로운 lumped 소자모델을 고려하여 최적설계를 수행하였다. 2GHz에서 동작하는 새로운 자성박막 인덕터는 photo-lithography와 lift-off기술을 이용하여 Si 기판위에 제작되었다. 50개 이상의 동일한 인덕터들의 주파수 특성은 RF Impedance Analyzer로, 자기공진주파수는 Vector Network 분석기(HP8510)로 측정되었다. 개발된 인덕터들은 1.8~2.3GHz 범위의 자기공진주파수, 47~68nH 범위의 L값, 그리고 1GHz이상의 주파수에서 70~80정도의 Q값을 가지므로 L과 Q가 극대화된 아주 우수한 최적구조의 소형(면적=30.8$\times$30.8mil2) 박막인덕터가 성공적으로 제작되었다.

• Journal of electromagnetic engineering and science
• /
• 제6권1호
• /
• pp.53-61
• /
• 2006

In this paper, we present parametric studies for the optimum design of a hexagonal plate monopole antenna. The dependence of the antenna performance on various geometric parameters is investigated using a commercial electromagnetic software, from which an optimum design of a hexagonal plate monopole antenna is derived. Guidelines for determining initial parameter values are given. The diameter of the circular ground plane is minimized tlo 1/5 wavelength at the lowest operating frequency. The antenna impedance matching is controlled by adjusting the gap between the plate and the ground plane, the plate base width, and the base bevel angle. The antenna proposed in. this paper shows a reflection coefficient less than -10 dB and a $2.0{\sim}6.2$ dBi gain over $3{\sim}20$ GHz frequencies.

• Environmental Engineering Research
• /
• 제23권4호
• /
• pp.383-389
• /
• 2018

Microbial fuel cell (MFC) is an innovative environmental and energy system that converts organic wastewater into electrical energy. For practical implementation of MFC as a wastewater treatment process, a number of limitations need to be overcome. Improving cathodic performance is one of major challenges, and introduction of a current collector can be an easy and practical solution. In this study, three types of current collectors made of stainless steel (SS) were tested in a single-chamber cubic MFC. The three current collectors had different contact areas to the cathode (P $1.0cm^2$; PC $4.3cm^2$; PM $6.5cm^2$) and increasing the contacting area enhanced the power and current generations and coulombic and energy recoveries by mainly decreasing cathodic charge transfer impedance. Application of the SS mesh to the cathode (PM) improved maximum power density, optimum current density and maximum current density by 8.8%, 3.6% and 6.7%, respectively, comparing with P of no SS mesh. The SS mesh decreased cathodic polarization resistance by up to 16%, and cathodic charge transfer impedance by up to 39%, possibly because the SS mesh enhanced electron transport and oxygen reduction reaction. However, application of the SS mesh had little effect on ohmic impedance.

• 전자공학회논문지A
• /
• 제32A권2호
• /
• pp.96-110
• /
• 1995

Traveling-wave electrodes for the high-speed Ti:LiNbO$_{3}$ modulators are designed. For a solution to the problems of 1) phase-velocity mismatching between the optical wave and the Modulating M/W, 2) M/W electrode characteristic impedance mismateching, we assume devices with 1$\mu$m thick SiO$_{2}$ buffer layer between the electrode and the Ti:LiNbO$_{3}$ substrate. The electrode analyses are performed by the FEM using the second-order triangular elements. The optimum design parameters to satisfy the phase-velocity matching and the characteristic impedance matching are sought for. By use of the analyses' results, a Mach-Zehnder optical modulator with a CPW electrode is designed as an example. the band-width estimation is also illustrated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.166-171
• /
• 2002

The transmission loss coefficient is very important acoustic property in parallel with absorption and acoustic impedance categorizing the acoustical materials, which can control the acoustical problems. At the same time, the transmission loss coefficient is a key parameter to choose the optimum material for the analysis of acoustical characteristics of material using SEA(Statistical Energy Analysis). In this paper, the transmission loss coefficient measurement system using 4-microphone impedance tube is proposed, based on the idea calculating the full transfer matrix of the acoustical sample to test. The theoretical background and measurement system are introduced, and finally the measurement results are verified.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.323.1-323
• /
• 2002

The transmission loss coefficient is very important acoustic property in parallel with absorption and acoustic impedance categorizing the acoustical materials, which can control the acoustical problems. At the same time, the transmission loss coefficient is a key parameter to choose the optimum material for the analysis of acoustical characteristics of material using SEA(Statistical Energy Analysis). In this paper, the transmission loss coefficient measurement system usiong 4-microphone impedance tube is proposed, based on the idea calculating the full transger matrix of the acoustical sample to test. The theoretical backgroung and measurement system are introduced, and finally the measurement results are verified.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.506-512
• /
• 1997

Ultrasonic knives have been successfully used for the surgery of many medical fields. However, the conventional ultrasonic knives for surgical operation cannot be controlled its resonant frequency. So if the material to cut has different characteristic impedance then different ultrasonic knife will be needed. Because the optimum driving frequency of ultrasonic knife is different by characteristic impedance of material. In this work, using a frequency variable ultrasonic transducer made of multi-layered PZT vibrator, a frequency controllable ultrasonic knife will be suggested. The design and computation principles will be also derived. For this work, firstly, the characteristics of this ultrasonic knife will be analyzed by transmission line model equivalent circuit, and the free admittance characteristics and vibrational velocity distributions will be obtained. Secondly, we will design and make the frequency controllable electrical oscillator for driving this ultrasonic knife.