• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1141-1148
• /
• 1997

In the stamping industry the blank shape to be stamped into a designed shape has been conventionally determined from the try out process by the press engineers. The work needs a lot of time and thus leads a loss of productivity. In this study boundary element method for 2-dimensional potential problem was used to design optimum blank shapes for irregular press forming. Here we assumed that the blank is controlled by blank holder only and material flow at blank holder was under potential flow. The developed PC code for designing the optimum blank shape shows that the blank shapes for optimal drawing can be calculated within a few minute in pentium PC and the calculated shapes agree well with the experiments. However the application of this method is constrained only to the pressed product with flat bottom.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.275-280
• /
• 2004

Shape optimization was performed to obtain the precise shape of cutouts including the internal shape of cutouts in laminated composite plates by three dimensional modeling using solid element. The volume control of the growth-strain method was implemented and the distributed parameter chosen as Tsai-Hill fracture index for shape optimization. The volume control of the growth-strain method makes Tsai-Hill failure index at each element uniform in laminated composites under the initial volume. Then shapes optimized by Tsai-Hill failure index were compared with those of the initial shapes for the various load conditions and cutouts. The following conclusions were obtained in this study. (1) It was found that growth-strain method was applied efficiently to shape optimization of three dimensional cutouts in a laminate composite, (2) The optimal shapes of the various load conditions and cutouts were obtained, (3) The maximum Tsal-Hill failure index was reduced up to 67% when shape optimization was peformed under the initial volume by volume control of growth-strain method.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.187-192
• /
• 2000

The effects of diffuser shapes on the flowfields of a small-size turbo-compressor have been investigated by numerically and experimentally. It is important to optimal design of each elements for developing the small-size turbo-compressor Typical range of rotating speed of a small-size turbo-compressor is 40,000-70,000rpm. Numerical analyses are conducted to the rectangular and conical shapes of diffusers. Three-dimensional, steady, viscous governing equations are solved by SIMPLE algorithm. To prove the numerical results, experimental studies for the measurements of static pressure and temperature at the inlet and outlet boundaries are performed. Comparisons of these results are executed, and reasonable agreements are acquired.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1854-1868
• /
• 1995

An effective nesting algorithm has been proposed to allocate the arbitrary shapes on one or several raw sheets by applying the well-known simulated annealing algorithm as the optimization technique. In this approach, both the shapes to be allocated and the raw sheets are represented as the grid-based models. This algorithm can accommodate every possible situations encountered in cutting apparel parts from the raw leather sheets. In other words, the usage of the internal hole of a shape for other small shapes, handling of the irregular boundaries and the interior defects of the raw sheets, and the simultaneous allocation on more than one raw sheets have been tackled on successfully in this study. Several computational experiments are presented to verify the robustness of the proposed algorithm.

• Journal of Mechanical Science and Technology
• /
• 제18권7호
• /
• pp.1140-1149
• /
• 2004

The absorption characteristics of water vapor into a LiBr-H$_2$O solution flowing down on finned inclined surfaces are numerically investigated in order to study the absorbing performances of different surface shapes of finned tubes as an absorber element. A three-dimensional numerical model is developed. The momentum, energy, and diffusion equations are solved simultaneously using a finite difference method. In order to obtain the temperature and concentration distributions, the Runge-Kutta and the Successive over relaxation methods are used. The flat, circular, elliptic, and parabolic shapes of the tube surfaces are considered in order to find the optimal surface shapes for absorption. In addition, the effects of the fin intervals and Reynolds numbers are studied. The results show that the absorption mainly happens near the fin tip due to the temperature and concentration gradient, and the absorbing performance of the parabolic surface is better than those of the other surfaces.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.79-86
• /
• 2000

In this study, a method of optimal blank design using the sensitivity analysis has been proposed. To get sensitivity a well-known commercial code PAM-STAMP has been used. In order to verify this method, formings of square cup, clover shaped cup and L shaped cup have been chosen as the examples. With the predicted optimal blank both computer simulation and experiment are performed. Excellent agreements are recognized between the numerical results and the target contour shapes. Through the investigation, the proposed systematic method of optimal blank design is found to be effective in the design of the deep drawing process.

• 한국공작기계학회논문집
• /
• 제12권2호
• /
• pp.9-16
• /
• 2003

A strategy of the optimal shape design with FEA(Finite Element Analysis) for 2-D structure is proposed by comparing subproblem approximation method with first order approximation method. A cantilever beam with two different loading conditions, a concentrated load and an evenly distribute load, and truss structure with a concentrated loading condition are implemented to optimize the shape. It gives a good design strategy on the optimal truss structure as well as the optimal cantilever beam shape. It is found that the convergence is quickly finished with the iteration number below ten. Optimized shapes of cantilever beam and truss structure are shown with stress contour plot by the results of the subproblem approximation method and the first order approximation methd.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1410-1415
• /
• 2000

This paper introduces the experimental analysis of the resonator in the rolling piston type compressor for air conditioner. The resonator located between cylinder and bearing is a major factor in the noise reduction of the rotary compressor. Several shapes for the resonator which can be built in the space limitations are derived. Then optimal resonator type for the noise reduction is determined by noise tests. 6 design parameters of the type are found and optimal level for each design factor is deduced from Taguchi method.

• 대한기계학회논문집B
• /
• 제22권9호
• /
• pp.1325-1334
• /
• 1998

The objectives of the present study are to develop a systematic method rather than a conventional trial-and-error method for an optimal shape design using a mathematical theory, and to apply it to engineering problems. In the present study, an optimal condition for a minimum pressure loss in a two-dimensional curved duct flow is derived and then an optimal shape of the curved duct is designed from the optimal condition. In the design procedure, one needs to solve the adjoint Navier-Stokes equations which are derived from the Navier-Stokes equations and the cost function. Therefore, a computer code of solving both the Navier-Stokes and adjoint Navier-Stokes equations together with an automatic grid generation is developed. In a curved duct flow, flow separation occurs due to an adverse pressure gradient, resulting in an additional pressure loss. Optimal shapes of a curved duct are obtained at three different Reynolds numbers of 100, 300 and 800, respectively. In the optimally shaped curved ducts, the separation region does not exist or is significantly reduced, and thus the pressure loss along the curved duct is significantly reduced.

• 대한기계학회논문집B
• /
• 제37권4호
• /
• pp.323-329
• /
• 2013

본 연구에서는 나뭇잎 그물맥 구조를 시뮬레이션하기 위해 잎 그물맥을 상 하 보강 박막판과 비압축성 유체가 흐르는 중간층 구조로 모델링하여 다중물리 현상으로 간주하고, 위상 최적화법을 다중물리 설계영역에 적용하였다. Mindlin-Reissner 판 모델에 기인한 횡방향 전단잠금 문제를 해결하기 위해 P1 비적합 요소와 선택 감소 적분법을 이용하였다. 다시-스토크스 유체 유동 채널에 대해 최적설계법을 적용하여 유동 시스템의 다중물리 모델을 해석하였으며, 잎의 그물맥 시뮬레이션을 수행하였다. 계산된 최적형상을 잎의 자연 그물 맥 패턴과 비교하였으며 비슷한 형상을 얻었다. 이와 같은 학제간 연구를 통해 나무 잎 그물맥 시스템을 이해할 수 있는 계기가 될 것으로 사료된다.