• Journal of Power Electronics
• /
• v.3 no.4
• /
• pp.205-214
• /
• 2003

This paper proposes a simple control strategy based on the discontinuous PWM (DPWM) to balance the DC-link voltage of three-level neutral-point-clamped (NPC) inverter at low modulation index. It introduces new DPWM methods in multi-level inverter and one of them is used for balancing the DC-link voltage. The current flowing in the neutral point of the DC-link causes the fluctuation of the DC-link voltage of the NPC inverter. The proposed DPWM method changes the path and duration time of the neutral point current, which makes the overall fluctuation of the DC-link voltage zero during a sampling time of the reference voltage vector. Therefore, by using the proposed strategy, the voltage of the DC-link can be balanced fairly well and the voltage ripple of the DC-link is also reduced significantly. Moreover, comparing with conventional methods which have to perform the complicated calculation, the proposed strategy is very simple. The validity of the proposed DPWM method is verified by the experiment.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.653-663
• /
• 2017

Multilevel active neutral-point-clamped (ANPC) converter combines the advantages of three-level ANPC converter and multilevel flying capacitor (FC) converter. However, multilevel ANPC converter often suffers from capacitor voltage balancing problems. In order to solve the capacitor voltage balancing problems for five-level ANPC converter, phase-shifted pulse width modulation (PS-PWM) is used, which generally provides natural voltage balancing ability. However, the natural voltage balancing ability depends on the load conditions and converter parameters. In order to eliminate voltage deviations under steady-state and dynamic conditions, the active voltage-balancing control (AVBC) methods of floating capacitors and dc-link capacitors based on PS-PWM are proposed. First, the neutral-point current is regulated to balance the neutral-point voltage by injecting zero-sequence voltage. After that, the duty cycles of the redundant switch combinations are adjusted to balance the floating-capacitor voltages by introducing moderating variables for each of the phases. Finally, the effectiveness of the proposed AVBC methods is verified by experimental results.

• Food Science and Preservation
• /
• v.2 no.1
• /
• pp.173-183
• /
• 1995

This paper was carried out to investigate changes in chromatograms of polysacctatides and soluble pectins on Sephadex G-50 and non-cellulosic neutral sugars of polysaccharides isolated from cell wall of persimmon fruits treated with polygalacturonase and $\beta$-galactosidase in vitro. The chromatogram pattern of soluble pectins extracted from cell wall treated with $\beta$-galactosidase on Sephacryl S-500 column were similar to those of untreatment, but contents of soluble pectins treated with $\beta$-galactosidase were different from those of untreatment. The patterns of chromatograms In soluble pectins extracted from cell wall treated with polygalacturonase were more complex and lower molecular polymer than those of other cell wall-degrading enzyme treatments. Non-cellulosic neutral sugar of polysaccharides in fraction I of soluble material treated with polygalacturonase was rhamnose, those in fraction II were similar to those in fraction III and contents of arabinose, xylose and glucose were higher than contents of other non-cellulosic neutral sugars. Non-cellulosic neutral sugars of polysaccharides in fraction I in soluble material by $\beta$-galactosidase treatment were rhamnose, arabinose, galactose and mannose. Content of glucose of polysaccharides in fraction II was higher than that in fraction I . Non-cellulosic neutral sugars treated with mixed enzyme were rhamnose, fucose, arabinose, xylose, mannose, galactose and glucose. Compositions of non-cellulosic neutral sugars of polysaccharides in fraction I were similar to those in fraction II and III.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.55 no.1
• /
• pp.67-72
• /
• 2022

We investigated the changes in the egg diameter of chub mackerel Scomber japonicus with the stages of egg development (and distinguished between hydrated oocyte and non-hydrated oocyte) for 1, 2, 3, 5, 10, 15 and 30 days. The chub mackerel oocytes were preserved in seven fixing solutions (70% ethyl alcohol, 99.9% ethyl alcohol, 5% formalin, 10% formalin, 5% neutral buffered formalin, 10% neutral buffered formalin and Gilson's solution). At 30 days, the chub mackerel hydrated oocytes preserved in 70% ethyl alcohol and 99.9% ethyl alcohol had shrunk by 5.2% and 7.9%, respectively. Similarly, the non-hydrated oocytes in the same solutions shrunk by 10.3% and 14.0%, respectively. Oocytes preserved in Gilson's solution had an average egg diameter decrease in both the hydrated oocyte (by 16.9%) and non-hydrated oocytes (by 15.6%). The diameter of the preserved hydrated oocytes did not significantly differ between the 5% formalin, 10% formalin, 5% neutral buffered formalin and 10% neutral buffered formalin, with shrinkage percentages of 0.6%, 0.1%, 1.9% and 3.4%, respectively (P>0.05). Similarly, the shrinkage percentages of the non-hydrated oocytes were 4.3% (5% formalin), 5.5% (10% formalin), 4.3% (5% neutral buffered formalin), and 4.1% (10% neutral buffered formalin).

• Steel and Composite Structures
• /
• v.49 no.4
• /
• pp.431-440
• /
• 2023

The functionally graded (FG) porous plates are usually characterized by the non-symmetric elastic modulus distribution through the thickness so that the plate neutral surface does not coincide with the mid-surface. Nevertheless, the conventional analysis models were mostly based on the plate mid-surface so that the accuracy of resulting numerical results is questionable. In this context, this paper presents the neutral surface-based static and free vibration analysis of FG porous plates and investigates the differences between the mid- and neutral surface-based analysis models. The neutral surface-based numerical method is formulated using the (3,3,2) hierarchical model and approximated by the last introduced natural element method (NEM). The volume fractions of metal and ceramic are expressed by the power-law function and the cosine-type porosity distributions are considered. The proposed numerical method is demonstrated through the benchmark experiment, and the differences between two analysis models are parametrically investigated with respect to the thickness-wise material and porosity distributions. It is found from the numerical results that the difference cannot be negligible when the material and porosity distributions are remarkably biased in the thickness direction.

• Microbiology and Biotechnology Letters
• /
• v.8 no.2
• /
• pp.77-85
• /
• 1980

This experiment was conducted to investigate the conditions for production and the characteristics of pretenses. Aspergillus oryzae KC-15, which is selected as a superior strain for the production of the protease, was used in this study. The results obtained were as follows: 1. The optimum culture time for the production of acid, neutral and alkaline protease on wheat bran medium were about 48, 48 and 72hr, respectively. The protease-produced by the strain were mainly alkaline and neutral one, but the production of acid protease was feeble extremely. 2. The addition of NaH$_2$PO$_4$, Na$_2$HPO$_4$, glucose, rice powder and Na-glutamate respectively to wheat bran media were effective for the production of alkaline and neutral protease, and the addition of (NH$_4$)$_2$HPO$_4$, glucose and rice powder respectively were effective for the production of acid protease. 3. Characteristics of professes(equation omitted) 4. As a heat resistance agent, NaH$_2$PO$_4$was the most effective one. The optimum amount of NaH$_2$PO$_4$was 10mg for alkaline and neutral protease, and 5mg for acid protease. 5. The heat resistance of the Protease by NaH$_2$PO$_4$was not recognized mostly above 6$0^{\circ}C$. 6. After the treatment of enzyme solution with 10mg of NaH$_2$PO$_4$for 30 minutes at 55$^{\circ}C$, the residual activities measured for alkaline, neutral and acid protease were 58, 57 and 55％ respectively.

• The Journal of the Korean bone and joint tumor society
• /
• v.7 no.2
• /
• pp.41-50
• /
• 2001

Purpose : To investigate biochemical markers for osteosarcoma, activities of deoxyribocuclease(DNase), ribonuclease(RNase), 5'-nucleotidase, alkaline phosphatase and amylase were determined in the osteosarcoma tissue and serum of patients with osteosarcoma. Also studied were DNase, RNase in osteosarcoma tissue, isolating the enzymes from the sarcoma tissue and investigating the sarcoma specific enzymes. Materials and Methods : The experimental tissue and serum were obtained from twelve patients with osteosarcoma. The control group were obtained from the normal healthy tissue of the same patients. The tissue were centrifugalized to obtain extracts. The extracts were analized for the estimation of nucleic acid, protein contents and enzyme activities. And then each enzymes were isolated and analized by DEAE-cellulose chromatography and estimated for activities. Result : Activities of acid DNase, RNase, 5'-nucleotidase and alkaline phosphatase were significantly increased in osteosarcoma tissue. Neutral RNase in osteosarcoma tissue was shown to bo highly active, exhibiting secretory form of RNase inhibitor associated with the RNase was also increased. In the serum of patients with osteosarcoma, RNase activity was significantly increased. DEAE-cellulose column chromatographical analysis revealed that acid DNase was isolated as a single enzyme and neutral RNase as five isozymes in osteosarcoma tissue. Conclusion : The results indicated that combination of these enzymes could be used as markers for osteosarcoma. The results indicated that acid DNase and neutral RNase might play a role in genesis of sarcoma and suppression of sarcoma.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.253-253
• /
• 2012

Low temperature SiOx film process has being required for both silicon and oxide (IGZO) based low temperature thin film transistor (TFT) for application of flexible display. In recent decades, from low density and high pressure such as capacitively coupled plasma (CCP) type plasma enhanced chemical vapor deposition (PECVD) to the high density plasma and low pressure such as inductively coupled plasma (ICP) and electron cyclotron resonance (ECR) have been used to researching to obtain high quality silicon oxide (SiOx) thin film at low temperature. However, these plasma deposition devices have limitation of controllability of process condition because process parameters of plasma deposition such as RF power, working pressure and gas ratio influence each other on plasma conditions which non-leanly influence depositing thin film. In compared to these plasma deposition devices, neutral beam assisted chemical vapor deposition (NBaCVD) has advantage of independence of control parameters. The energy of neutral beam (NB) can be controlled independently of other process conditions. In this manner, we obtained NB dependent high crystallized intrinsic and doped silicon thin film at low temperature in our another papers. We examine the properties of the low temperature processed silicon oxide thin films which are fabricated by the NBaCVD. NBaCVD deposition system consists of the internal inductively coupled plasma (ICP) antenna and the reflector. Internal ICP antenna generates high density plasma and reflector generates NB by auger recombination of ions at the surface of metal reflector. During deposition of silicon oxide thin film by using the NBaCVD process with a tungsten reflector, the energetic Neutral Beam (NB) that controlled by the reflector bias believed to help surface reaction. Electrical and structural properties of the silicon oxide are changed by the reflector bias, effectively. We measured the breakdown field and structure property of the Si oxide thin film by analysis of I-V, C-V and FTIR measurement.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.387-394
• /
• 2006

In this study, the effect of using a neutral beam formed by low-angle forward reflection of a reactive ion beam on aspect-ratio-dependent etching (ARDE) has been investigated. When a SF6 Inductively Coupled Plasma and $SF_6$ ion beam etching are used to etch poly-Si, ARDE is observed and the etching of poly-Si on $SiO_2$ shows a higher ARDE effect than the etching of poly-Si on Si. However, by using neutral beam etching with neutral beam directionality higher than 70 %, ARDE during poly-Si etching by $SF_6$ can be effectively removed, regardless of the sample conditions. The mechanism for the removal of ARDE via a directional neutral beam has been demonstrated through a computer simulation of different nanoscale features by using the two-dimensional XOOPIC code and the TRIM code.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.4
• /
• pp.333-342
• /
• 2009

Three-level Diode Clamped Multilevel Inverter, generally known as Neutral-Point-Clamped (NPC) Inverter, has an inherent problem causing Neutral Point (NP) potential variation. Until now, in many literatures NP potential problem has been investigated and lots of solutions have also been proposed. However, under fault and fault tolerant control, distinctive feature for NP potential variation problem was rarely published from the standpoint of reliability. In this paper, NP potential is analytically investigated both normal and faulty conditions under carrier based PWM. Subsequently, relation between fault detection time and size of capacitor is analyzed. This information is explored by simulation and experiment results, which contribute to enhance the reliability of inverter system.