• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2079-2084
• /
• 2007

A small-scale thermoelectric cooling system was built in an effort to enhance the performance of the refrigeration system by utilizing the water-cooled jacket which was attached on the hot side of the thermoelectric module. Considered design parameters for the water-cooled jacket included the geometry of the flow passage inside the jacket and the flow rate of cooling water. The higher flow rate of cooling water in the jacket resulted in a better performance of the refrigeration system. The introduction of geometrical complexity of the cooling water flow passage to the cooling jacket also showed significant improvement on the performance of the thermoelectric refrigeration system such as the cooling capacity and the COP of the refrigeration system.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.3
• /
• pp.81-91
• /
• 2015

LED has received intensive research attention due to its long life, high efficacy, fast response and wide colour availability, and has secured extensive application areas. However, LED chips within the modules convert only fraction of electric energy into light, and majority of supplied energy needs to be dissipated as heat, which challenges in the performance and life of the LED modules. IEC 62717 specifies the performance requirements for LED modules together with the test methods and conditions. The present study examined the influence of different design parameters on performance temperature through series of experiments and numerical simulations. The economic means to change the module performance temperature during the measurement of mandatory markings were suggested based on predicted cooling performances.

• Communications for Statistical Applications and Methods
• /
• v.19 no.4
• /
• pp.571-577
• /
• 2012

Modules that consist of software are respectively coded in the early development phase and the modules are unified as a software. After unification, the software is repeatedly tested with a given taskset (the set of module tasks that are tested simultaneously) until a required performance level is satisfied. In this paper, we expand the one-module software debugging model of Jang and Lee (2011) to a multi-module debugging model and derive the taskset completion probability and the mean of the completed tasksets under the assumption that the processing times of module tasks given in a taskset are mutually dependent.

• Journal of Korean Institute of Industrial Engineers
• /
• v.38 no.4
• /
• pp.262-275
• /
• 2012

This paper develops a multistage scheduling algorithm for the module operation of the LCD(Liquid Crystal Display) production systems and tests the efficiency of the proposed algorithm. The module operation is a multistage form composed of multiple sub operations of processes, and each stage is consists of multiple lines with the same kinds of machines. This paper presents a mathematical modeling reflecting the constraints of the LCD module operation and develops a multistage scheduling algorithm based on tabu search metaheuristic approach. For this purpose, an production order is assigned to a line of the sub operations and a sequence of the assigned order is rearranged to draw an efficient schedule. Simulation experiments test performance measures and show the efficiency of the proposed algorithm.

• ETRI Journal
• /
• v.20 no.3
• /
• pp.284-300
• /
• 1998

A new thermosyphon cooling module (TSCM) has designed, fabricated and tested to cool the multi-chip module consists of a cold plate and an integrated condenser. With an allowable temperature rise of $56^{\circ}C$ on the surface of the heater, the cooling module TSCM can handle a heat flux of about 2.7 $W/cm^2$ using R11 as working fluid. The transient characteristics of the cooling module have been proved to be excellent: that is, when a heat load is applied inside of the system, steady state can be achieved within 10 to 15 minutes. It has been found that the length of the vapor channel between the cold plate and the condenser in addition to the ambient and the condenser temperatures affect the system performance.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.107-110
• /
• 2005

This paper describes the design and fabrication of synchronous clock recovery module for S-DMB Gap Filler. Using the 2.304MHz TTL signal from gap filler tuner, clock recovery module with 10MHz output frequency including holdover function is designed. The measured performance of the clock recovery module shows a stability of less than 0.01ppm, 29 sec stability time, 10 sec holdover time, and maximum -113dBc/Hz@100Hz phase noise.

• ETRI Journal
• /
• v.30 no.2
• /
• pp.275-281
• /
• 2008

A 40 Gb/s clock and data recovery (CDR) module for a fiber-optic receiver with improved phase-locked loop (PLL) circuits has been successfully implemented. The PLL of the CDR module employs an improved D-type flip-flop frequency acquisition circuit, which helps to stabilize the CDR performance, to obtain faster frequency acquisition, and to reduce the time of recovering the lock state in the event of losing the lock state. The measured RMS jitter of the clock signal recovered from 40 Gb/s pseudo-random binary sequence ($2^{31}-1$) data by the improved PLL clock recovery module is 210 fs. The CDR module also integrates a 40 Gb/s D-FF decision circuit, demonstrating that it can produce clean retimed data using the recovered clock.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.393-397
• /
• 2013

This paper introduces the T/RX combined compact active channel module which is a key unit of the active phased array antenna(APAA) system. This module is mainly compoased of two parts for TX and RX fabricated on both sides of the active module for size reduction. The TX-part is primarily composed of a 3-stage amplifier, a microstrip phase shifter, a thermal compensation and a power detection circuit. The RX-part is composed of LNAs a microstrip phase shifter and BPFs for TX power rejection. Using the proposed design structure we can realized a compact active channel module having high performance.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.591-595
• /
• 2011

In this paper, we design the hardware architecture of the BICM(Bit Interleaved Coded Modulation) module for next generation European broadcast system and implement the BICM module with DSP(Digital Signal Processor) TMS320C6474. Simulation result shows that the BER(Bit Error Rate) performance of the fixed-point BICM module using more than 8 bits is very similar to that of the floating-point BICM module.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.243-247
• /
• 1996

A general procedure for motion capture and mimic system has been delineated. Utilizing sensors operated in the magnetic fields, complicated and optimized movements are easily digitized to analyze and reproduce. The system consists of a motion capture module, a motion visualization module, a motion plan module, a motion mimic module, and a GUI module. Design concepts of the system are modular, open, and user friendly to ensure the overall system performance. This procedure is being implemented on a virtual cyber cube. and an inverted pendulum. With modifications, this procedure can applied for complicated motion controls.