• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.267-267
• /
• 2013

Band engineering of a nanowire is related to the question what is the minimum size of a nanowire-based device. At the subnanometer scale, there has been a long standing problem whether it is possible to both control an energy band of an isolated nanowire by a dopant and measure it using angle-resolved photoemission spectroscopy (ARPES). This is because an extra atom in the subnanometer wire plays as a defect rather than a dopant and it is challenging to assemble isolated subnanometer wires into an array for an ARPES measurement. We demonstrate that only one of multiple metallic subnanometer wires canbe controlled electronically by a dopant maintaining the whole metallic bands of other wires, which was observed directly by ARPES. Here,the multiple metallic subnanometer wires were produced on a stepped Si(111) surface by a self-assembly method. The selective band engineering proves that the selectively-controlled metallic wire is nearly isolated electronically from other metallic wires and an electronic structure controlcan be realized down to subnanometer scale.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.157-158
• /
• 2013

• ETRI Journal
• /
• v.30 no.4
• /
• pp.597-599
• /
• 2008

This letter presents the design of a small and low-profile RFID tag antenna in the UHF band that can be mounted on metallic objects. The designed tag antenna, which uses a ceramic material as a substrate, consists of a radiating patch and a microstrip line with two shorting pins for a proximity-coupled feeding structure. Using this structure, impedance matching can be simply obtained between the antenna and tag chip without a matching network. The fractional impedance bandwidth for $S_{11}$ <3 dB and radiation efficiency are about 1.4% and 56% at 911 MHz, respectively. The read range is approximately from 5 m to 6 m when the tag antenna is mounted on a metallic surface.

• Transactions of Materials Processing
• /
• v.10 no.7
• /
• pp.565-572
• /
• 2001

It is well known that a multicomponent $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ bulk metallic glass alloy shows good bulk glass forming ability due to its high resistance to crystallization in the undercooled liquid state. DSC and XRD have been performed to confirm the amorphous structure of the master alloy. To investigate the mechanical properties and deformation behavior of the bulk metallic $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy, a series of compression tests has been carried out at the temperatures ranging from $351^{\circ}C$ to $461^{\circ}C$at the various initial strain rates from $2{\times}10^4s^1$ to $2{\times}10^2s^1$. Three types of nominal stress-strain curves have been identified such as linear stress-strain relationship meaning fracture at maximum stress, plastic deformation including stress overshoot and steady-state flow, plastic deformation without stress overshoot depending on the strain rate and test temperature. Also DSC analysis for the compressed specimens was carried out to investigate the change of structure, thermal stability and crystallization behavior for the various test conditions.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.344-349
• /
• 2015

An interconnect is the key component of solid oxide fuel cells that electrically connects unit cells and separates fuel from oxidant in the adjoining cells. To improve their surface stability in high-temperature oxidizing environments, metallic interconnects are usually coated with conductive oxides. In this study, lanthanum nickelates ($LaNiO_3$) with a perovskite structure are synthesized and applied as protective coatings on a metallic interconnect (Crofer 22 APU). The partial substitution of Co, Cu, and Fe for Ni improves electrical conductivity as well as thermal expansion match with the Crofer interconnect. The protective perovskite layers are fabricated on the interconnects by a slurry coating process combined with optimized heat-treatment. The perovskite-coated interconnects show area-specific resistances as low as $16.5-37.5m{\Omega}{\cdot}cm^2$ at $800^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.31 no.6
• /
• pp.331-338
• /
• 2021

Ti-Al-Si target and Cr-Si target are sputtered alternately to develop a multi-layered nitride coating on a steel mold to improve die-casting lifetime. Prior to the multi-layer deposition, a CrN layer is developed as a buffer layer on the mold to suppress the diffusion of reactive elements and enhance the cohesive strength of the multi-layer deposition. Approximately 50 nm CrSiN and TiAlSiN layers are deposited layer by layer, and form about three ㎛-thickness of multi-layered coating. From the observation of the uncoated and coated steel molds after the acceleration experiment of liquid metal injection casting, the uncoated mold is severely eroded by the adhesion of molten metallic glass. On the other hand, the multi-layer coating on the mold prevents element diffusion from the metallic glass and mold erosion during the experiment. The multi-layer structure of the coating transforms the nano-composite structured coating during the acceleration test. Since the nano-composite structure disrupts element diffusion to molten metallic glass, despite microstructure changes, the coating is not eroded by the 1,050 ℃ molten metallic glass.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.6
• /
• pp.630-636
• /
• 2016

In this paper, a novel triple-mode cavity structure, designed for compactness and operating at 850 MHz, is analyzed. A cylindrical dielectric resonator is loaded into a metallic cylindrical cavity. Previous study has been focused on the analysis of the cylindrical dielectric resonator, but in this paper, the effect of the cylindrical metallic cavity has been analyzed. Enclosing the dielectric resonator inside the metallic cavity increases the resonant frequency of the dielectric resonator; however, this increases the quality factor and introduces the possibility of installing coupling screws. The principle of generation of triple-mode was investigated by parametric analysis. The generated triple-mode is TE011 mode and two orthogonally generated HEM121 modes. By adjusting the radius of the dielectric resonator, the height of the dielectric resonator, or the radius of the cylindrical metallic cavity, three modes could be coincided. However, the height of the metallic cavity keeps three modes separated. The mode characteristics of the proposed cavity are analyzed using a full-wave electromagnetic (EM) simulation. The proposed triple-mode cavity could be developed to triple-mode filter using a coupling screw, and the commercial application for the miniaturized filter below 1 GHz could be expected.

• Transactions of Materials Processing
• /
• v.14 no.8 s.80
• /
• pp.718-724
• /
• 2005

An efficient finite element method has been introduced for analysis of metallic sandwich plates subject to bending moment. A full model 3-point bending FE-analysis shows that the plastic behavior of inner structures appears only at the load point. The unit structures of sandwich plates are defined to numerically calculate the bending stiffness and strength utilizing the recurrent boundary condition for pure bending analysis. The equivalent models with the same bending stiffness and strength of full models are then designed analytically. It is demonstrated that the results of both models are almost the same and the FE-analysis method incorporating the equivalent models can reduce the computation time effectively. The dominant collapse modes are face buckling and face yielding. Since the inner dimpled structures prevent face buckling, sandwich plates with inner dimpled shell structure can absorb more energy than other types of sandwich plates during the bending behavior.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.73-80
• /
• 2014

In this study, in order to investigate the influence of insolubilizer on the double coating structure, we carried out basic research related to the double coating formulation with four insolubilizers having various chemical types such as amino aldehyde, glyoxal and two metallic salts. It was found that although the four insolubilizers showed similar results on optical and surface properties of the coated papers, they gave different results in the printabilities of the coated papers since coating structure was significantly influenced by different reacting mechanism of the insolubilizers. Three of the insolubilizers (glyoxal, two metallic salts) showed better results than amino aldehyde type one when they were applied to top coating formulation. Metallic salts type insolubilizers showed good results in the print gloss when it was applied to top coating formulation. It was believed that amino aldehyde type insolubilizer applied top coating formulation showed good both of dry-pick and wet-pick strength.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.1-15
• /
• 2015

In this invited paper, the authors give an overview of the new design technology for a metallic backplane-less metamaterial(MM) absorber and discuss a selection of examples. In contrast to a common MM absorber structure, the metallic pattern layer of the presented structure is placed facing toward the incident wave propagation direction to reduce the radar cross section(RCS) due to the metallic pattern itself at frequencies other than the targeted absorption frequency bands. The ability of the MM backplane-less absorber to exhibit broadband absorption performance and irregular surface applications will be discussed.