• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.166-171
• /
• 2016

Nickel silicide is main issue in Polycrystalline silicon Thin Film Transistor (TFT) which is made by Metal Induced Lateral Crystallization (MILC) method. This Nickel silicide acts as a defect center, and this defect is one of the biggest reason of the high leakage current. In this research, we fabricated polycrystalline TFTs with novel method called Edge Cut (EC). With this new fabrication method, we assumed that nickel silicide at the edge of the channel region is reduced. Electrical properties are measured and trap state density also calculated using Levinson & Proano method.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.33-39
• /
• 1997

The crystallization temperature of an amorphous silicon (a-Si) can be lowered down to 400.deg. C by a new method : Double-metal induced lateral crystallization (DMILC). The a-Si film was laterally crystallized from Ni and Pd deposited area, and its lateral crystallization rate reaches up to 0.2.mu.m/hour at that temperature and depends on the overlap length of Ni and Pd films; the shorter the overlap length, the faster the rate. Poly-Silicon thin film transistors (poly-Si TFT's) fabricated by DMILC at 400.deg. C show a field effect mobility of 38.5cm$^{3}$/Vs, a minimum leakage current of 1pA/.mu.m, and a slope of 1.4V/dec. The overlap length does not affect the characteristics of the poly-Si TFT's, but determines the lateral crystallization rate.

• Journal of Information Display
• /
• v.2 no.2
• /
• pp.7-12
• /
• 2001

A viscous Ni solution was coated over amorphous Si thin film for evenly spread of Ni metal source. The Ni s. prepared by dissolving $NiCl_2$ into IN HCI and mixing with propylene glycol. $NiCl_2$ and Ni were deposited on the amorphous film after oven dry and they enabled to obtain a uniform crystallization. The crystallization using the viscous Ni solution was a Ni-silicide mediated process, the same process used with Ni metal layer. The crystallization temperature was lowered to $480^{\circ}C$ by the synergy effect of silicide-mediated crystallization and microwave-induced crystallization. Lateral crystallization was also enhanced such that the velocity of lateral crystallization by microwave annealing became faster than by furnace annealing.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.274-277
• /
• 2000

Thin Film Transistor(TFTs) were fabricated from poly-Si crystallized by a two-step annealing process on glass substrates. The combination of low-temperature(500$^{\circ}C$) Metal-Induced Lateral Crystallization(MILC) furnace annealing and high -temperature (700$^{\circ}C$) rapid thermal annealing leads to the improvement of the material quality The TFTs measured with this two-step annealing material exhibit better characteristics than those obtained by using conventional MILC furnace annealing.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.4
• /
• pp.31-37
• /
• 2000

In the case of metal-induced lateral crystallization (MILC) for low temperature poly-Si TFT, offset length between Ni-thin film and the sides of gate could be modified to control the location of MILC boundary. Electrical characteristics were compared to analyze the effect of MILC boundary that was located either in or out of the channel region of the TFT. By removing the MILC boundary from channel region, on current, subthreshold slope and leakage current properties could be improved. When MILC boundary was located in the channel region, leakage current was reduced with electrical stress biasing. The amount of reduction increased as the channel width increased, but it was independent of the channel length.

• Journal of Convergence for Information Technology
• /
• v.9 no.5
• /
• pp.117-124
• /
• 2019

This paper discusses recent trends in the fabrication of semiconducting materials among the components of thin film transistors used in AMOLED display. In order to obtain a good semiconductor film, it is necessary to change the amorphous silicon into polycrystalline silicon. There are two ways to use laser and heat. Laser-based methods include sequential lateral solidification (SLS), excimer laser annealing (ELA), and thin-beam directional crystallization (TDX). Solid phase crystallization (SPC), super grain silicon (SGS), metal induced crystallization (MIC) and field aided lateral crystallization (FALC) were crystallized using heat. We will also study research for manufacturing large AMOLED displays.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.985-988
• /
• 2008

Metal induced crystallization of a-Si with a source of Ni/Si oxide was studied. Its mechanism to induce crystallization was discussed. It was found that new source behaves an effect of self-released nickel and reducing nickel residua, so can provide a wider process tolerance; improve the uniformity and stability of TFTs.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.578-581
• /
• 2004

In this study, we proposed the novel method that can crystallize the amorphous silicon by adjacent Pd-MILC enhanced Ni-MILC. With this method, the MILC rate was about 15 ${\mu}$m/h at 550$^{\circ}C$ which is four times faster than conventional MILC rate. The crystallization rate increased rapidly with the spacing between Ni and Pd decreased. And it was independent on Ni and Pd layer thickness and amorphous silicon active width. However, when Pd was capped by a Ni layer, there's no enhancement on Ni-MILC. This phenomenon implies that the enhancement of Ni-MILC rate comes from not Pd material itself but Pd-MILC induced tensile stress. We can explain these phenomena with a novel MILC mechanism.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.48-53
• /
• 1998

Poly-Si TFT's could be fabricated on glass substrates by metal induced lateral crystallization (MILC) method at 450.deg. C. Channel area of the poly-Si TFT's was laterally crystallized from source and drain areas, where a thn nickel film was deposited. Dopants activation for the formation of source and drain region could be achieved by thermal annealing at 450.deg. C after the ion mass doping of phosphorus. The field effect mobility of thus formed N-channel poly-Si TFT's was 76cm$^{2}$/Vs, and the on/off current ratio was higher than 7E6.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.05a
• /
• pp.107-107
• /
• 1997