• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2002년도 추계학술발표대회
• /
• pp.315-320
• /
• 2002

Marketing ventilation fan 3 kinds been using in kitchen of apartment house into compensation discharge performance of contaminant measure. When propane gas burns by gas table, did waste heat into measurement compensation with carbon dioxide that it happens. In measured all type of exhaust fan, discharge performance of carbon dioxide and waste heat was high there are been much displacement. Among A, B, C three types, performance of A type exhaust fan was most superior and performance of C type exhaust fan was most poor

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.97-100
• /
• 2006

This study performed numerical analysis for obtaining optimal frequency and damping ratio of tuned mass damper (TMD) using 20 seismic loads measured at rock site. The structures of $1{\sim}2$ second natural period were considered, and optimal frequency and damping ratio were estimated for different mass ratio in terms of displacement and absolute acceleration response control. Numerical results showed that the values of the optimal parameters were different those from previous study by Hartog.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 B
• /
• pp.1193-1195
• /
• 1996

For an automatic steering problem of vehicles, the main task is to keep a reference path with assumption that the displacement from the guideline can be measured by a sensor. In this paper, a sliding mode fuzzy logic controller design method is introduced and it shows highly enhanced performance in comparison with the other results. The method can be relatively simply implemented.

• 전기학회논문지
• /
• 제60권9호
• /
• pp.1733-1740
• /
• 2011

In this research, a MEMS vibratory gyroscope with dual-mass system in the sensing mode has been proposed to increase the stability of the device using wide bandwidth. A wide flat region between the two resonance peaks of the dual-mass system removes the need for a frequency matching typically required for single mass vibratory gyroscopes. Bandwidth, mass ratio, spring constant, and frequency response of the dual-mass system have been analyzed with MATLAB and ANSYS simulation. Designed first and second peaks of sensing mode are 5,917 and 8,210Hz, respectively. Driving mode resonance frequency of 7,180Hz was located in the flat region between the two resonance peaks of the sensing mode. The device is fabricated with anodically bonded silicon-on-glass substrate. The chip size is 6mm x 6mm and the thickness of the silicon device layer is $50{\mu}m$. Despite the driving mode resonance frequency decrease of 2.8kHz and frequency shift of 176Hz from the sensing mode due to fabrication imperfections, measured driving frequency was located within the bandwidth of sensing part, which validates the utilized dual-mass concept. Measured bandwidth was 768Hz. Sensitivity calculated with measured displacement of driving and sensing parts was 22.4aF/deg/sec. Measured slope of the sensing point was 0.008dB/Hz.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.25-29
• /
• 2006

본 연구는 가압상태에서 오링 변형 거동을 측정하기 위한 새로운 시험 기법을 개발하기 위함이다. 전산화 단층촬영으로 압출 틈에서 측정한 압출 길이와 비접촉 레이저 변위 센서로 측정한 압출 길이는 결과가 일치하였다. 전산화 단층촬영에서 측정한 변형된 오링 형상과 유한요소법으로 해석하여 얻은 오링 형상은 압출 길이와 확장 지름은 일치하였으나, 오링과 스틸의 접촉 길이는 전산화 단층촬영의 결과가 유한요소해석의 결과보다 약간 크게 측정되었다.

• 수산해양기술연구
• /
• 제58권2호
• /
• pp.121-129
• /
• 2022

Density and sound speed contrasts (g and h, respectively), and swimming angle were measured for sandfish (Arctoscopus japonicus) without swimbladder. The density contrast was measured by the volume displacement method while the sound speed contrast was measured by the acoustic measurements of travel time (time-of-flight method). The swimming angle was measured by dividing it into daytime, nighttime, daytime feeding and nighttime feeding. The g was 1.001 to 1.067 with an average (± standard deviation) of 1.032 (± 0.017), and the h was 1.007 to 1.022 with an average (± standard deviation) of 1.015 (± 0.003). The swimming angles (mean ± standard deviation) were 16.8 ± 10.3° during the daytime, 1.9 ± 12.3° during the nighttime, 30.2 ± 12.6° in the daytime feeding and 35.0 ± 13.2° in the nighttime feeding. These results will provide important parameters input to calculate theoretical scattering models for estimating the acoustic target strength of sandfish.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1744-1746
• /
• 1999

In this paper, we give pressure stimulation into organic ultra thin films and detected the induced displacement current properties, and then manufacture a device under the accumulation condition. In processing of a device manufacture, we can see the process is good from the change of a surface pressure and transfer ratio of area per molecule of organic ultra thin films. The structure of manufactured device is MIM(Au/polyimide LB films/AU), the number of accumulated 19 layers. I-V characteristic of the device is measured from -5[V] to +5[V]. The maximum value of measured current is increased as the number of accumulated layers are decreased. The insulation of a thin film is better as the interval between electrodes is larger, and the insulation properties of a thin film is better as the distance between electrodes is larger.

• 한국지반공학회지:지반
• /
• 제12권3호
• /
• pp.83-98
• /
• 1996

이 논문에서는 역순법 원리를 이용한 역해석 결과를 제시하였다. 국내에서 건설된 두 곳의 지하비축기지 공사 중에 계측한 자료를 이용하여 비축기지 진입터널 주위 암반의 변형계수와 초기 지압을 계산하였다. 역해석에서 얻어진 결과를 입력자를로 하여 유한요소해석을 수행하였으며 그 결과를 계측치와 비교, 검토하였다.

• Tribology and Lubricants
• /
• 제20권5호
• /
• pp.278-283
• /
• 2004

O-ring seal is widely used for sealing pressure vessels and oil containers in various applications of mechanical equipments. The doughnut shape of the O-ring is very important components in most of the system assembly of mechanical apparatus. This paper presents the sealing force of a pressurized perfluoroelastomer O-ring, which is very important contact seal in sealing the semiconductor equipment. The sealing pressure is measured by experimental method and analyzed numerically by using the non-linear MARC finite element program. The seal tester is made to measure the contact force and displacement of the O-ring with an automatic control system of the working temperature. The results show the reasonable agreements between the computed FEM results and measured ones when the operating temperature is moderate temperature. But the compared values between the computed and tested results show a difference because of the increased temperature, which is related to the non-linear parameter of the O-ring material.

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.872-880
• /
• 2002

The finite element analysis is frequently used to predict dynamic responses of complex structures. Since the predicted responses often differ from experimentally measured ones, updating of the finite element models is performed to make the finite element results agree with the measured ones. Among several model updating methods, one is to use FRF(frequency response function) data without a modal analysis. This paper investigates characteristics of the model updating method in order to improve the method. The investigation is focused on how to obtain FRFs for unmeasured rotational displacements and how to consider damping. For the investigation simulated data and experimental data for a cantilever beam are used.