• Elastomers and Composites
• /
• 제51권1호
• /
• pp.38-42
• /
• 2016

For improving the heat loss of a refrigerator around door gasket, it is very important to reduce the amount of rubber magnet used, of which thermal conductivity is much higher than the plastics, and enhancing the magnetic properties of rubber magnet itself is crucial for this. In the present study, therefore, a relationship between the optimum conditions of rubber magnet fabrication process and raw material compositions in the ferrite powder/CPE binder compounds was investigated for finding a way to enhance the magnetic properties of rubber magnet. Magnetic attraction forces of a sample rubber magnet was measured as function of distance, and thermal properties of the sample ferrite powder/CPE binder compound were analyzed with TG/DTA thermal analyzer. As a results, a rubber magnet strip with enhanced magnetic properties was expected to be fabricated, of which raw material compound was prepared by compounding with higher ferrite magnetic powder concentration.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권2호
• /
• pp.53-58
• /
• 2001

This paper describes a moving mesh technique for dynamic characteristics analysis of permanent magnet linear synchronous motor with the secondary aluminium sheet. The moving mesh technique applied to the linear induction motor can be used to analyze the linear synchronous motor with the rectangular permanent magnet. But in case of the permanent magnet with taper, the shape of the permanent magnet is presented. The time-stepped finite element method is used for the dynamic characteristics simulation of the permanent magnet linear synchronous motor, The results of application example(hysteresis current controlled inverter fed control) such as thrust, current and flux plots are shown.

• 대한전기학회논문지
• /
• 제45권1호
• /
• pp.24-29
• /
• 1996

Magnetic field theories for the design of highly homogeneous magnet are introduced and a nonlinear optimization method for the design of actively shielded superconducting magnet is presented. The presented design method can optimize both main coil and shielding coil simultaneously by setting constraints on stray field intensity at a specified distance from the magnet center. A 2-Tesla actively shielded superconducting magnet, with 90cm bore diameter, is designed using the presented method. The field homogeneity is 2ppm/30cm DSV and the 5 gauss stray field contour is within 4m axially and 3m radially from the magnet center. (author)., 7 refs., 6 figs., 3 tabs.

• 조명전기설비학회논문지
• /
• 제29권10호
• /
• pp.47-53
• /
• 2015

IPMSM(Insert Permanent Magnet Synchronous Motor) is a very high degree of freedom in the design according to the permanent magnet insertion position. And the performance of IPMSM is affected a lot on barrier shape which determines the magnetic flux path from magnet. Thus the position of permanent magnet and the barrier shape has to be designed by considering both specification and operation condition. In the paper, the permanent magnet and barrier shape which is suitable for direct drive motor of washing machine has been studied. In addition, in order to verify the validity of the study, the test was evaluated by making a prototype motor.

• 한국초전도ㆍ저온공학회논문지
• /
• 제21권2호
• /
• pp.45-49
• /
• 2019

This paper reports comparison between analytic and numerical simulation approaches for calculation of screening current and screening current induced field in a high temperature superconductor magnet. Bean slab model is adopted to calculate screening current and SCF analytically, while the finite element method numerically. A case study of screening current and SCF calculation are conducted with a magnet, a 7 T 68 mm cold-bore multi-width no-insulation GdBCO magnet built and tested by Massachusetts Institute of Technology Francis Bitter Magnet Laboratory. In this study, we assume the magnet is dunked in liquid nitrogen at 77 K. Furthermore, the simulation results are compared in terms of computation time and accuracy. Finally, discussion on the different methods together with the comparison between the calculations and experiment is provided.

• 대한전기학회논문지
• /
• 제39권8호
• /
• pp.813-819
• /
• 1990

In this paper, a new design method for superconducting pulse magnet is presented. Given energy storage capacity, magnet shape parameters are determined to minimize superconducting material quantity. Once the shape parameters are determined, cooling channel is designed and degradation characteristics are confirmed. According to the proposed magnet design concept, relatively uniform and low field distribution is obtained. Therefore, both the quantity of superconducting material and the mechanical load over magnet are reduced.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.699-701
• /
• 2000

It leaves much room for improvement that UTM-01 is of practical use. Therefor we will design of UTM-02 system. The design of new magnet is based on light weight for bogie system. We used Maxwell-3D FEM for design of new magnet. The new magnet for UTM-02 that was reduced weight of magnet. 22kg, then it was increased ratio lift to weight is 9.87.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.503-504
• /
• 2010

• 자원리싸이클링
• /
• 제28권3호
• /
• pp.26-34
• /
• 2019

희토류 영구자석(Rare earth magnet)은 사용량이 급격하게 증가하고 있으며, 이와 맞물려 폐희토류 자석의 발생량도 급격히 증가할 것으로 예측된다. 폐희토류 자석의 재활용은 주로 자석에 포함되어 있는 희토류 원소를 침출/분리하여 회수하는 공정으로 이루어지고 있으나, 침출 공정에 투입되는 폐희토류 자석의 분쇄 특성에 대한 연구는 전무한 실정이다. 따라서 본 연구에서는 폐희토류 자석을 이용하여 효과적인 파분쇄 공정 및 분쇄특성에 대한 연구를 진행하였다. NdFeB 폐자석을 조크러셔로 파쇄한 결과 급격한 산화 없이 효과적으로 입도가 감소는 하였지만, 롤크러셔의 경우 지속적인 압축에 의해 증가하는 표면과 대기 중의 산소가 반응하여 불꽃을 내며 급격한 산화가 발생하였다. 또한 파쇄 공정을 통해 생산된 시료를 볼밀에 투입하여 분쇄 특성을 파악한 결과, 일반적인 광물과 다르게 분쇄가 잘 이루어지지 않고 분쇄 16분 이후에 정상적인 분쇄가 이루어졌다. 또한 일반적인 광물에 비해 매우 낮은 분쇄율(S)과 미분이 발생이 매우 높은 분쇄분포(B)를 보임을 확인하였으며, 이는 향후 NdFeB 폐자석 파분쇄 공정 설계 시 기초자료로 사용될 수 있을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.834-839
• /
• 2007

This paper investigates the distortion of magnetic field of a brushless DC (BLDC) motor due to deformed rubber magnet. Global or local deformation of rubber magnet in the BLDC motor is mathematically modeled by using the Fourier series. Distorted magnetic field is calculated by using the finite element method, and unbalanced magnetic force are calculated by using the Maxwell stress tensor. The first harmonic deformation in the global deformation of rubber magnet generates the first harmonic driving frequency of the unbalanced magnetic force, and the rest harmonic deformations of rubber magnet except the harmonic deformation with multiple of common divisor of pole and slot introduces the driving frequencies with multiple of slot number ${\pm}1$ to the unbalanced magnetic force. However, the harmonic deformation with multiple of common divisor of pole and slot does not generate unbalanced magnetic force due to the rotational symmetry. When the rubber magnet is locally deformed, the unbalanced magnetic force has the first harmonic driving frequency and the driving frequencies with multiples of slot number ${\pm}1$.