• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.7
• /
• pp.659-664
• /
• 2016

In this paper, we suggest operational trans-conductance amplifier(OTA) for current-mode FIR filter that can be used in a digital circuit system requiring high operating frequency and low power consumption. The current-mode signal processing is one of the very innovative design method for a low power consumption system with high operating frequency because it shows a constant power regardless of frequency. From the simulation result using 0.35um CMOS process, when Vdd is 2V, it is confirmed that the proposed circuit showed the dynamic range of the about 1V, about 50% of supply voltage and output current swing of about 0~200uA. Also, the power consumption was evaluated with about 21uW and the active size for an integration was measured with $71um{\times}166um$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.4A
• /
• pp.365-372
• /
• 2007

In IEEE 802.11b wireless network, stations synchronize themselves to the beacons periodically sent by the access point(AP) when they are running in low power mode. In case of missing beacon due to noise or traffic from neighboring wireless network stations must be awake until they get the next beacon, which causes energy consumption in stations. In this paper, we propose a scheme searching next beacon consuming little energy. The problems of missing beacon in low power mode of IEEE 802.11b wireless interface are described and a new method to reduce energy consumption is proposed. The proposed method is simulated with the network simulator, ns2, and compared with the low power mode of the IEEE 802.11b. The result measured in terms of station's wakeup time shows some enhancement in energy consumption when some errors occur in receiving frames.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1A
• /
• pp.65-71
• /
• 2006

In IEEE 802.11b wireless network, the access point(AP) sends beacons periodically to manage stations when they are running in low power mode. Stations contend for the transmission medium after they receive a beacon and continuously check its state until it becomes available. Thus the energy consumption of each station increases as the load of wireless network. In this paper, we propose a method to reduce energy consumption controlling virtual bitmap in wireless network with multiple stations. The problems of low power mode in IEEE 802.11b wireless interface are described and a new method to reduce energy consumption is proposed. The proposed method is simulated with the network simulator, ns2, and compared with the low power mode of the IEEE 802.11b. The result measured in terms of station's wakeup time shows some enhancement in energy consumption when multiple stations are communicating through the AP in wireless network.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.4
• /
• pp.17-23
• /
• 2012

Ultra low-power design and energy harvesting applications require digital systems to operate under extremely low voltages approaching the point of balance between dynamic and static power consumption which is attained in the sub-threshold operation mode. Delay variations are extremely large in this mode. Therefore, in this paper, a new low-power logic design methodology using asynchronous NCL circuits is proposed to reduce power consumption and not to be affected by various technology variations in nanoscale MOSFET technology. The proposed NCL is evaluated using various benchmark circuits at 0.4V supply voltage, which are designed using 45nm MOSFET predictive technology model. The simulation results are compared to those of conventional synchrouns logic circuits in terms of power consumption and speed.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.255-266
• /
• 2015

In this paper, a low-complexity and low-power soft output multiple input multiple output (MIMO) symbol detector is proposed for mobile devices with two transmit and two receive antennas. The proposed symbol detector can support both the spatial multiplexing mode and spatial diversity mode in single hardware and shows the optimal maximum likelihood (ML) performance. By applying a multi-stage pipeline structure and using a complex multiplier based on the polar-coordinate, the complexity of the proposed architecture is dramatically decreased. Also, by applying a clock-gating scheme to the internal modules for MIMO modes, the power consumption is also reduced. The proposed symbol detector was designed using a hardware description language (HDL) and implemented using a 65nm CMOS standard cell library. With the proposed architecture, the proposed MIMO detector takes up an area of approximately $0.31mm^2$ with 183K equivalent gates and achieves a 150Mbps throughput. Also, the power estimation results show that the proposed MIMO detector can reduce the power consumption by a maximum of 85% for the various test cases.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.585-586
• /
• 2008

In this paper, a novel beta-multiplier reference current source circuit for the 800mV power-supply voltage is presented. In order to cope with the narrow input common-mode range of the OpAmp in the reference circuit, shunt resistive voltage divider branches were deployed. High gain OpAmp was designed to compensate intrinsic low output resistance of the MOS transistors. The proposed reference circuit was designed in a standard 0.18um CMOS process with nominal Vth of 420mV and -450mV for nMOS and pMOS transistor respectively. The total power consumption including OpAmp is less than 50uW.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.1
• /
• pp.39-45
• /
• 2009

OFDM is used for achieving a high-speed data transmission in mobile wireless communication systems. Conventionally, fast Fourier transform that is the main signal processing of OFDM is implemented using digital signal processing. The DSP FFT LSI requires large power consumption. Current-mode FFT LSI with analog signal processing is one of the best solutions for high speed and low power consumption. However, for the operation of current-mode FFT LSI that has the structure of parallel-input and parallel-output, current-mode serial-to-parallel and parallel-to-serial converter are indispensable. We propose a novel current-mode SPC and PSC and full chip simulation results agree with experimental data. The proposed current-mode SPC and PSC promise the wide application of the current-mode analog signal processing in the field of low power wireless communication LSI.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2076-2084
• /
• 2016

In this paper, a novel scheme to eliminate common-mode voltage (CMV) is proposed for three-level neutral-point clamped (NPC) inverters. In the proposed scheme, a low-power full-bridge converter is utilized to produce compensatory voltage for CMV, which is injected into an NPC inverter through a single-phase four-winding transformer. With the proposed circuit, the power range for applications is not limited, and the maximum modulation index of the inverter is not reduced. These features are suitable for high-power medium-voltage machine drives. The effectiveness of the proposed method is verified by simulation and experimental results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.402-403
• /
• 2009

A variety of power reduction technologies is introduced and the benefits of the technologies are discussed. PenTile$^{(R)}$ DBLC (Dynamic Brightness LED Control) combined with SABC (Sensor-Based Adaptive Brightness Control) enables to achieve the average LED power consumption to one third. The panel power reduction of 25% can be achieved with low power driving technology, ALS (Active Level Shifter). MIP (Memory In Pixel) is expected to be useful in transflective display because the whole display area can be utilized in reflective mode with power consumption of 1mW.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.407-417
• /
• 2018

A novel family of Buck mode three-level direct ac converters with a high frequency link is proposed. These converters can transfer an unsteady high ac voltage with distortion into a regulated sinusoidal voltage with a low THD at the same frequency. The circuit configuration is constituted of a three-level converter, high frequency transformer, cycloconverter, as well as input and output filters. The topological family includes forward, push-pull, half-bridge, and full-bridge modes. In order to achieve a reliable three-level ac-ac conversion, and to overcome the surge voltage and surge current of the cycloconverter, a phase-shifted control strategy is introduced in this paper. A prototype is presented with experimental results to demonstrate that the proposed converters have five advantages including high frequency electrical isolation, lower voltage stress of the power switches, bi-directional power flow, low THD of the output voltage, and a higher input power factor.