• 해양환경안전학회지
• /
• 제20권2호
• /
• pp.218-227
• /
• 2014

본 연구에서는 실험 모형을 이용한 탄소성 대변형 시리즈 해석을 수행하여 플레이트 거더의 파손모드와 최종하중을 예측하였다. 수치해석 모형의 붕괴모드는 재하 시 플랜지에서 소성 힌지가 형성되었으며 실험모형의 붕괴모드와 일치하였다. 또한, 웹에서 항복선이 형성되어 크리플링 붕괴모드가 발생하는 것을 관찰할 수 있었으며 각각의 실험모형과 수치모형 최종하중의 평균값 1.07, 표준편차 0.04, 변동계수 0.04로 선형성을 유지하였으며 전체 최종하중 결과도 대략 8 % 오차를 나타내었다. 이는 수치모형 결과가 실험 및 적용 기준에 매우 만족하고 양호한 결과를 도출하였다고 생각한다. 따라서 알루미늄합금 플레이트 거더의 최종하중 예측 시 실험 및 적용 기준과 함께 병행하여 적용을 한다면 이에 대한 합리적 안전수준을 유지한다면 더 효율적이고 경제적 알루미늄 합금 플레이트 거더의 파손모드 및 최종하중에 대해 예측할 수 있을 거라고 생각한다.

• 산업경영시스템학회지
• /
• 제34권4호
• /
• pp.35-41
• /
• 2011

The purpose of this study was to examine drivers' driving behaviors and eye-movements according to driving speed and navigation- position while operation of the navigation in driving. For this purpose, two driving conditions (low-speed and high-speed) and two navigation-positions (top and bottom location of the center console) were set. Drivers' driving behaviors (speed, speed variation, coefficient of variation, and the number of collisions) and eye-movements (overall eye pattern, the average scanning time of navigation, and the number of gaze-out on the road for more 2 seconds) were measured. As a result, when the navigation was located at the bottom of the console, difficulties of lateral control was appeared in low-speed driving condition, and the that of longitudinal control was appeared in high-speed driving condition. In addition, above situation made the drivers' scanning times of navigation long, increased the number of gaze-out on the road for more 2 seconds, and made overall eye pattern monotonous. These results could be interpreted that the manipulation of the navigation at the bottom of console cause reduced attention capacity due to the cognitive load.

• 콘크리트학회논문집
• /
• 제17권2호
• /
• pp.293-302
• /
• 2005

This study describes data from determination of the optimum mix proportion and site application of the mass concrete placed in bottom slab and side wall having a large depth and section as main structures of LNG in-ground tank. This concrete requires low heat hydration, excellent balance between workability and consistency because concreting work of LNG in-ground tank is usually classified by under-pumping, adaptation of longer vertical and horizontal pumping line than ordinary pumping condition. For this purpose, low heat Portland cement and lime stone powder as cementitious materials are selected and design factors including unit cement and water content, water-binder ratio, fine aggregate ratio and adiabatic temperature rising are tested in the laboratory and batch plant. As experimental results, the optimum unit cement and water content are selected under $270kg/m^3$ and $l55{\~}l60 kg/m^3$ separately to control adiabatic temperature rising below $30^{\circ}C$ and to improve properties of the fresh and hardened concrete. Also, considering test results of the confined water ratio($\beta$p) and deformable coefficient(Ep), $30\%$ of lime stone powder by cement weight is selected as the optimum replacement ratio. After mix proportions of 5cases are tested and compared the adiabatic temperature rising($Q^{\infty}$, r), tensile and compressive strength, modulus of elasticity, teases satisfied with the required performances are chosen as the optimum mix design proportions of the side wall and bottom slab concrete. $Q^{\infty}$ and r are proved smaller than those of another project. Before application in the site, properties of the fresh concrete and actual mixing time by its ampere load are checked in the batch plant. Based on the results of this study, the optimum mix proportions of the massive concrete are applied successfully to the bottom slab and side wall in LNG in-ground tank.

• 한국해양공학회지
• /
• 제31권4호
• /
• pp.266-273
• /
• 2017

In recent years, LNG bunkering terminals are needed to supply LNG as fuel to meet the emission requirements of the International Maritime Organization (IMO). A floating LNG bunkering terminal (FLBT) is one of the most cost-effective and environmentally friendly LNG bunkering systems for storing LNG and transferring it directly to an LNG fuel vessel. The FLBT maintains its position using mooring systems such as spread mooring and turret mooring. The loads on the vessel and mooring lines must be carefully determined to maintain their positions within the operable area. In this study, the wind loads acting in several side-by-side arrangements on the FLBT and LNG-BS were estimated using wind tunnel tests in the Force Technology, and the shielding effect due to the presence of ships upstream was evaluated. In addition, the empirical formulations proposed by Fujiwara et al. (2012) were used to estimate the wind force coefficients acting on the FLBT and those results were compared with experimental results.

• 한국세라믹학회지
• /
• 제40권9호
• /
• pp.881-885
• /
• 2003

인공치관용 알루미나-유리 복합체를 in vitro 분위기인 $37^{\circ}C$) 인공타액 하에서 49N~196N의 하중조건 하에서 ball-on-disc 형태로 120rpm의 회전속도로 직경 14mm인 트랙을 $10^{6}$) 횟수까지 내마모거동을 조사하기 위하여 내마모실험을 수행하였다. 하중이 49N,98N 196N으로 증가함에 따라, 마찰계수는 0.025로 일정하였지만 마모율은 2.18${\times}$$10^{-9}$$mm^{3}$/N.m, 3.37${\times}$$10^{-9}$$mm^{3}$/N.m, 2.35${\times}$$10^{-6}$$mm^{3}$/N.m로 증가하였다. 실험결과, 알루미나-유리 복합체의 마모거동은 마모길리 44km까지 전형적인 흡착마모로 치열교정용 세라믹 브라켓으로 적합하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권2호
• /
• pp.149-155
• /
• 2008

최근 교통소통의 필수적인 수단으로 많은 도로가 건설 중에 있으며 기 시공된 도로 등은 차량의 통행과 기후 등의 여러 요인에 의해 내하력이 저하되고 있다. 본 연구에 적용된 지반의 흙의 종류와 소성지수 그리고 비중은 각각 SC, 12.2%, 2.66이였으며 최대건조단위중량, 최적함수비, 수정CBR은 각각 $1.895g/cm^2$ (수정다짐 D), 13.6%, 16.2%였다. 이러한 지반조건에서 동적콘관입시험의 관입지수로부터 추정한 CBR과 소형 FWD시험의 동적변형계수로부터 환산한 정적변형계수 사이에는 상관계수가 0.90으로 높은 상관성을 나타내었다.

• 한국자동차공학회논문집
• /
• 제23권3호
• /
• pp.344-351
• /
• 2015

Braking force inspection of vehicles in service is certainly one of the most important characteristics that affect vehicle safety. Up to now, in domestic country, the regular safety inspection of vehicles in service has been tested with a roller type brake test (a static braking force inspection system). But, in EU and USA etc. in recent years, it has been tested with a plate type brake test (a dynamic braking force inspection system). In this study, to compare the characteristics of above two test systems, the correlations for the results of braking force are evaluated statistically. As the results, in the case of main braking force, the range of the $R^2$ of the deviation for the left and right side is 0.5386 ~ 0.6231 in the rear axle and 0.0032 ~ 0.0052 in the front axle respectively, then the $R^2$ in the front axle is lower than that in the rear axle and the total variation is unexplained by the least-squares regression line statistically. Also, the p-value for the deviation of the left and right in the front axle is 0.4839 ~ 0.5755, then it has nonsignificant in the front axle. Therefore, the static braking force inspection system can not reflect the inertia force that there is a load transfer from the rear axle to the front axle during braking. Accordingly, it is necessary to adopt the dynamic braking force inspection system which can reflect the inertia force on the regular vehicle safety inspection in domestic country.

• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.411-417
• /
• 2013

철도선로에 설치되는 전철주기초의 모멘트에 대한 거동을 파악하기 위한 실물 재하시험을 수행하였다. 현장타설방식으로 설치된 폭 1.1m, 깊이 2.2m의 정사각형 전철주기초 2본에 대하여 실제 조건과 동일한 모멘트 위주의 하중을 가하여 기초의 항복모멘트를 확인하였다. 거푸집 설치 여부가 기초의 저항모멘트에 미치는 영향을 평가하기 위하여 동일한 조건에서 거푸집을 설치한 경우와 그렇지 않은 경우에 대하여 시험하였다. 거푸집 설치 효과로 흙과 지반의 접촉면이 매끈해지면서 발생하는 마찰력 감소보다는, 거푸집 미설치 시 굴착지반의 이완에 의한 기초 주변지반의 강도 감소 효과가 더 크게 나타나는 것으로 나타났다. 비례계수를 사용하여 포괄적으로 전철주기초의 저항모멘트를 산정하는 현행 설계방법으로는 거푸집의 설치효과를 적절히 고려할 수 없었으며, 연직응력과 마찰력을 분리하여 저항모멘트를 산정하는 경우에는 기초와 지반의 마찰각을 20% 감소시킴으로써 거푸집 설치효과에 대한 합리적인 고려가 가능하였다.

• 한국산학기술학회논문지
• /
• 제17권5호
• /
• pp.237-242
• /
• 2016

본 논문은 돌산대교 모형 사장교에 하중을 주었을 때 발생되는 변위를 측정하기 위한 방법으로 디지털 영상처리 방법을 도입하여 실험을 하였다. 돌산대교 모형 사장교는 30:1로 축소한 경우로 길이 15.5m, 너비 400mm이다. 실험 방법은 영상처리 결과를 ANSYS 해석결과와 변위계 측정결과를 비교, 분석하여 영상처리 기법의 타당성을 검증하였다. 본 실험에 적용된 영상처리 기법은 상호상관 계수를 적용하였으며, 실험 조건은 100kgf 재하 하였을 때의 변위와 200kgf 재하 하였을 때의 변위를 측정하는 실험을 수행하였다. 분석 결과 하중이 추가적으로 증가하여 발생되는 변위가 커질수록 영상처리에 대한 신뢰성도 증가하는 것으로 나타났다. 즉, 하중이 100kgf에서 200kgf으로 증가할 때, ANSYS 결과대비 오차율이 31%에서 14%로 감소하였으며, 변위계 결과대비 오차율 역시 17%에서 4%로 감소하였다. 200kgf 재하시 14%, 4%의 차이를 보이고 있어, 영상처리 기법으로 충분히 변위를 측정할 수 있을 것으로 판단된다. 향후 연구로는 동영상 파일로 부터 고유진동수를 측정하는 방법에 대해서 연구하고자 한다.

• 한국도로학회논문집
• /
• 제15권1호
• /
• pp.1-9
• /
• 2013

PURPOSES: The purpose of this study is to evaluate physical properties, durability, fatigue resistance, and long-term performance of poly-urethane concrete (PU) which can be possible application of thin layer on long-span orthotropic steel bridge and to check structural stability of bridge structure. METHODS : Various tests of physical properties, such as flexural strength, tensile strength, bond strength and coefficient of thermal expansion tests were conducted for physical property evaluation using two types of poly urethane concrete which have different curing time. Freezing and thawing test, accelerated weathering test and chloride ion penetration test were performed to evaluate the effect of exposed to marine environment. Beam fatigue test and small scale accelerated pavement test were performed to assess the resistance of PU against fatigue damage and long-term performance. Structural analysis were conducted to figure out structural stability of bridge structure and thin bridge deck pavement system. RESULTS: The property tests results showed that similar results were observed overall however the flexural strength of PUa was higher than those of PUb. It was also found that PU materials showed durability at marine environment. Beam fatigue test results showed that the resistances of the PUa against fatigue damage were two times higher than those of the PUb. It was found form small scale accelerated pavement test to evaluate long-term performance that there is no distress observed after 800,000 load applications. Structural analysis to figure out structural stability of bridge structure and thin bridge deck pavement system indicated that bridge structures were needed to increase thickness of steel deck plate or to improve longitudinal rib shape. CONCLUSIONS: It has been known that the use of PU can be positively considered to thin layer on long-span orthotropic steel bridge in terms of properties considered marine environment, resistance of fatigue damage and long-term performance.