• Journal of ILASS-Korea
• /
• v.26 no.2
• /
• pp.81-87
• /
• 2021

This study was performed to calculate the swirl ratio of a diesel engine intake port by a 1D computer simulation under actual engine operating conditions. The swirl ratio of the intake port was simulated according to the change of the engine speed during the operation of the motoring without fuel injection. The swirl ratio of the intake port was simulated according to changes in the crank angle during the four-cycle operation of intake, compression, expansion and exhaust. The swirl ratio represented by the three regions of the piston, center and squish was simulated. Among the three regions, the piston-region swirl ratio is important for effective air-fuel mixing in the engine cylinder. In particular, it was confirmed during the simulation that the piston swirl ratio before and after the compression top dead center (TDC) point when fuel is injected in the DI diesel engine can have a significant effect on the mixing of air and fuel. It was desirable to set the average piston swirl ratio over a crank angle section before and after compression TDC as the representative swirl ratio of the cylinder head intake port according to the change of the engine speed.

• Journal of ILASS-Korea
• /
• v.26 no.4
• /
• pp.189-196
• /
• 2021

Spray drift of agricultural nozzles has become a big issue because it causes low precision targeting and environmental pollution. In order to reduce the spray drift, study spray characteristics of agricultural nozzles is virtually important. In this study, shadowgraph and Mie-scattering visualization techniques were used to study the macroscopic spray and atomization characteristics of an agricultural nozzle. PDPA was used to measure the atomization characteristics of spray. The injection pressure is set to 1 bar, 3 bar and 5 bar, which covers the working range of the nozzle. For the PDPA experiment, 75 points were measured in an area of 160 mm × 120 mm at 10 mm intervals directly below the nozzle to grasp the overall atomization characteristics of the spray. It was found that the spray width and sheet width showed a linear correlation. As the injection pressure increased, the sheet expansion in the 0-degree direction and the sheet swing in the 90-degree direction jointly promoted the breakup of the sheet. In addition, the area close to the central axis had a large droplet velocity, and since a large droplet velocity promoted atomization of spray, the area close to the central axis had a smaller spray droplet diameter than the left and right regions.

• Corrosion Science and Technology
• /
• v.22 no.4
• /
• pp.287-296
• /
• 2023

Li-ion batteries have been gaining increasing importance, driven by the growing utilization of renewable energy and the expansion of electric vehicles. To meet market demands, it is essential to ensure high energy density and battery safety. All-solid-state batteries (ASSBs) have attracted significant attention as a potential solution. Among the advantages, they operate with an ion-conductive solid electrolyte instead of a liquid electrolyte therefore significantly reducing the risk of fire. In addition, by using high-capacity alternative electrode materials, ASSBs offer a promising opportunity to enhance energy density, making them highly desirable in the automotive and secondary battery industries. In ASSBs, Li metal can be used as the anode, providing a high theoretical capacity (3860 mAh/g). However, challenges related to the high interfacial resistance between Li metal and solid electrolytes and those concerning material degradation during charge-discharge cycles need to be addressed for the successful commercialization of ASSBs. This review introduces and discusses the interfacial reactions between Li metal and solid electrolytes, along with research cases aiming to improve these interactions. Additionally, future development directions in this field are explored.

• Nuclear Engineering and Technology
• /
• v.56 no.3
• /
• pp.922-932
• /
• 2024

This paper presents the design features and preliminary design analysis results of the Wielenga Innovation Static Salt Reactor (WISSR). The WISSR incorporates features that make it both flexible and inherently safe. It is based on innovative technology that controls a nuclear reactor by moving molten salt fuel into or out of the core. The reactor is a low-pressure, fast spectrum transuranic (TRU) burner reactor. Inherent shutdown is achieved by a large negative reactivity feedback of the liquid fuel and by the expansion of fuel out of the core. The core is made of concentric, thin annular fuel chambers containing molten fuel salt. A molten salt coolant passes between the concentric fuel chambers to cool the core. The core has both fixed and variable volume fuel chambers. Pressure, applied by helium gas to fuel reservoirs below the core, pushes fuel out of a reservoir and up into a set of variable volume chambers. A control system monitors the density and temperature of the fuel throughout the core. Using NaCl-(TRU,U)Cl₃ fuel and NaCl-KCl-MgCl₂ coolant, a road-transportable compact WISSR core design was developed at a power level of 1250 MWt. Preliminary neutronics and thermal-hydraulics analyses demonstrate the technical feasibility of WISSR.

• Journal of Embryo Transfer
• /
• v.25 no.3
• /
• pp.189-193
• /
• 2010

We investigated the cleavage rate and blastocyst yield for each culture condition to enhance tolerance of cryo-preservation of bovine IVF embryo with relatively lower cryo-tolerance compared to in vivo embryo. The cleavage rate and blastocysts yield for CR1aa, IVMD, IVD, CR1aa+10% FBS were 73.2, 69.3, 72.8, 68.5% and 44.1, 30.8, 33.3, 48.0%, respectively. The values did not differ among each treatments without serum. For embryo vitrification, In vivo and In vitro blastocysts were exposed to VS1(10% glycerin, 0.1 M glucose, 0.1 M sucrose, PEG 1%) for 5 min, and VS2 (10% glycerin, 10% EG, 0.2 M glucose, 0.2 M sucrose, PEG 2%) for 5 min and then VS3 (10% glycerin, 30% EG, 0.3 M glucose, 0.3 M sucrose, PEG 3%) for 1 min. The exposed embryos were then loaded into the 0.25 ml plastic straws and then plunged into liquid nitrogen. The straws were held for period of 1 to 2 weeks before thawing. In embryo viability, no differences in blastocyst re-expansion rates were found between in vivo and in vitro embryos. whereas expansion-BL rates was significantly higher for in vivo-derived embryos (72.7%) when compared to in vitro-derived embryos (51.4%), respectively (P<0.05). In conclusion, our results indicate that combined use of CRIaa culture medium with vitrification might enhance tolerance of cryopreservation for bovine IVF embryo production.

• Resources Recycling
• /
• v.8 no.1
• /
• pp.23-28
• /
• 1999

Firing characteristics, transverse rupture strength, and heat capacity were studied of the heat-reservoir refractory materials made of red-firing clay, mill scale, and water glass. The firing shrinkage increased with increase of the clay proportion in samples. The volume of fired bodies showed shrinkage by drying up to $300^{\circ}C$, steady expansion in the 300-$700^{\circ}C$ range due to phase transition of iron oxides. and drastic expansion above $1200^{\circ}C$. Flexural strength decreased from 5.6 Mpa to 2.35 Mpa with the decrease of the ratio of clay to mill scale from 1:1 to 1:3 Heat capacities changed from 1.1 Joul/g$^{\circ}$C to 1.35 Joul/g$^{\circ}$C with the ratio of millscale to clay ratio from 1:1 to 1:3. Mill scale in the specimen appears to exist as liquid phase during firing. Firing the specimens in air leads to the eruption of the molten mill scale to the sample surfaces. Contrarily, firing samples in a refractory sagger with a cover suppressed the eruption of the molten mill scale to the surfaces. The addition of mill scale gave rise to porous sintered bodies which would delay cooling rates of heat-reservoir brick.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.68-79
• /
• 2018

An examination of the characteristics of the ground material in is very important in a ground investigation. Casagrande classified soil using the material properties of soils. The liquid-plastic limit test is useful for obtaining basic information of soil, and is an effective method for classifying silt and clay, as well as the material properties, such as shear strength, shrinkage, and expansion. Unlike the liquid limit test, the plasticity limit test is due to the ambiguity of the test procedure. Many geotechnical engineers and scholars have questioned the test results. In this study, a new plasticity limit method was used to compare with the thread rolling method with kaolinite, ilite and bentonite at a certain ratio, and samples were collected from the west coast of Korea. As a result of the comparison, the test value of the new test method showed high reproducibility because the error range of the test value of the conventional thread rolling test was only 10% but the error range of the new test values decreased to 2%. The difference in the slope of the existing plasticity test values was 0.1519 ~ 0.1925, and the results of the test were similar or coincided with each other. Aone - point method was proposed to make it easier to apply the new test method.

• Korean Journal of Optics and Photonics
• /
• v.33 no.5
• /
• pp.218-229
• /
• 2022

We have investigated reliable inspection methods for finding the defects generated during the manufacturing process of lightweight, large-aperture satellite telescope mirrors using silicon carbide, and we have measured the basic physical properties of the mirrors. We applied the advanced ceramic material (ACM) method, a combined method using liquid-silicon penetration sintering and chemical vapor deposition for the carbon molded body, to manufacture four SiC mirrors of different sizes and shapes. We have provided the defect standards for the reflectors systematically by classifying the defects according to the size and shape of the mirrors, and have suggested effective nondestructive methods for mirror surface inspection and internal defect detection. In addition, we have analyzed the measurements of 14 physical parameters (including density, modulus of elasticity, specific heat, and heat-transfer coefficient) that are required to design the mirrors and to predict the mechanical and thermal stability of the final products. In particular, we have studied the detailed measurement methods and results for the elastic modulus, thermal expansion coefficient, and flexural strength to improve the reliability of mechanical property tests.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.1
• /
• pp.39-47
• /
• 2024

In this study, physical property tests and standard consolidation tests were conducted on the marine clay of Busan New Port and North Port, the middle and lower reaches of the Nakdong River including Gimhae and Yangsan, and Ulsan regions. The moisture content, a property unrelated to sample disturbance with small individual test errors, was used for regression analysis with the compression index, virgin compression index, consolidation coefficient, expansion index, and secondary compression index, among others. Subsequently, the correlation and accuracy were evaluated. Upon analyzing the correlation between the moisture content, void ratio, and liquid limit commonly used physical properties for calculating compression indexes, it was confirmed that the liquid limit had the lowest correlation. Through a linear regression analysis of the consolidation constants using the current moisture content in the natural state, a high correlation was demonstrated. Relationship equations were then presented to determine settlement and settlement time. This study suggests that moisture content can be utilized as an alternative for evaluating and calculating consolidation constants when examining ground settlement in sedimentary clays distributed in the Busan and Gyeongnam regions.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.8
• /
• pp.43-56
• /
• 2019

This research has been conducted to suggest an estimation equation of compression index to be practically applied to the southeastern areas by finding out physical and mechanical characteristics of 229 points on the southeastern coast areas (Busan area: 78 points, Gimhae area: 103 points, Geoje area: 18 points, Changwon area: 30 points) through indoor tests and analyzing its relation to the compression index. From the results, we could not only find out correlation between natural water content, liquid limit and initial void ratio versus compression index for soft ground on each of the southeastern coast areas, but also an integrated correlation equation of the southeastern coast areas. In addition, we have performed a comparative analysis of the existing estimated equation of compression index and that found in this paper. As a result, the existing estimated equation suggested by foreign researchers has shown considerable error to be applied to the soft ground on the southeastern coast areas in Korea. The estimated equation of compression index with the water content out of the existing estimated equations has shown minimum 10.8% to maximum 48.1% of error rate, minimum 13.4% to maximum 288.5% of error rate with liquid limit or minimum 9.4% to maximum 211.4% of error rate with initial void ratio. On the other hand, error rates calculated with the estimated equations of compression index from this research have shown minimum 10.5% to maximum 13.4% with water content, minimum 11.6% to maximum 21.3 with liquid limit or minimum 7.1% to maximum 11.7% with initial void ratio, for better results than those with existing estimated equations. In addition, relation between compression index and expansion index has shown Cs = (1/5 ~ 1/12)Cc similar to the existing relation of Cs = (1/5 ~ 1/10)Cc.