• Korean Journal of Materials Research
• /
• v.16 no.2
• /
• pp.85-91
• /
• 2006

The fraction of $\varepsilon\;and\;\gamma$'-iron nitride in compound layer is predicted by x-ray diffraction using direct comparison method. The validity of formulation models was checked by comparing calculated results with metallographic analysis of iron nitride compound layer grown on steel S45C by gas nitriding. The fraction of $\varepsilon$ calculated by the three phase model, porous-$Fe_3N$/ dense-$Fe_3N$/ mixed layer with $Fe_3N\;and\;Fe_4N$, is 80 percent of that analyzed by etching technique. The $\varepsilon$ fraction predicted by mixed layer model is 122 percent of that measured by microscope.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.215-216
• /
• 2002

This paper describes the wear characteristics of WC-Co cemented carbides machined with Wire-cut or Die-sinking EOM. We prepared the specimens with different grades of grinding to remove the affected layer after the EDM. These specimens were experimented by block-on-cylinder type tribometer. The result indicated that although the hardness of the affected layer was lower than that of the bulk, wear resistance was increased. In order to investigate the cause of the increase in wear resistance of the affected layer, the layer was observed and analyzed by SEM and ESCA. We also discussed the mean free path of Co phase.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.11
• /
• pp.3086-3096
• /
• 1999

To declare conformance of multi-protocol Implementation Under Test(IUT), every layer of the multi-protocol IUT should be tested. According to ISO9646, single-layer test method is applied to testing the highest layer of multi-protocol IUT and single-layer embedded test method is used for the layers by layer all the protocols in a multi-protocol IUT. This paper proposes a new method for testing a multi-protocol IUT. The proposed test method assumes that a multi-protocol IUT is under test and that the interfaces between the layers cannot be controlled or observed by the tester. We apply the proposed test method to TCP/IP and compare the application results with those of the existing test turns out that the proposed test method significantly reduces the number of test cases as well as the number of test events while providing the same test coverage. In addition, the proposed test method shows the capability to locate the layer that is source of failure in testing multi-protocol IUTs.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.212-214
• /
• 2004

Hardware implemented ring buffer systems and methods are presented for the effective management of the ring buffer in TCP/IP communication. The layer interface of the ring buffer systems transfer free buffer and used buffer size information to the TCP/IP stack upper or low layer. The pointer updation interface calculates a temporary pointer from the data size which is needed by the present pointer of the ring buffer and upper or lowyer layer. The pointer manager of the ring buffer systems is responsible for saving the present pointer of the ring buffer, updating the ring buffer pointer to the new pointer, calculating the free buffer size and used buffer size of the ring buffer, and transferring the information to the upper layer. The ring buffer systems help the TCP/IP layer and TCP/IP upper or lower layer to decide the sending or receiving data size effectively. The delay of transferring data can be lowered by the ring buffer system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.357-364
• /
• 2001

This study deals with the effect on non-martensitic layer on the fatigue strength in carburized gear. The test gears are carburized, then treated by the combination of chemical polishing and electro-polishing. Carburization treatment is used widely on parts of power transmission system like surface hardened layer to improve fatigue strength. Carburized gears are observed using a scanning electron microscope(SEM) to determine the characteristics of crack initiation mechanism in the surface layer. The constant street amplitude fatigue test is performed by using and electro-hydraulic servo-controlled pulsating tester. The S-N curves are obtained and illustrated. The effect of non-martensitic layer on the fatigue strength is clarified.

• Journal of Environmental Science International
• /
• v.12 no.4
• /
• pp.367-373
• /
• 2003

The focus of this study was to identify and describe environmental preconceptions held by pre-service elementary teachers about three issues : greenhouse effect, ozone layer depletion and acid rain. Two hundred and twenty nine pre-service elementary teachers participated in this study. A 36 question survey was created by one of the authors. The questions focused on the cause, effects, and interactions of three environmental issues greenhouse effect of one layer depletion and acid rain. Pre-service elementary teachers answered the questions on a Likert scale. An analysis of the survey data indicated that the majority of pre-service elementary teachers possess an array of incorrect conceptions about the causes and effects of the greenhouse effect ozone layer depletion, and acid rain. and also many pre-service elementary teachers thought that there were causal relationships among the increase in greenhouse effect, the destruction of ozone layer, and the increase of acid rain.

• Applied Microscopy
• /
• v.24 no.1
• /
• pp.102-113
• /
• 1994

A thin section of the methanogenic archaebacterium, Methanoplanus limicola, shows that the surface glycoprotein array (S-layer) is separated from plasma membrane by a distinct inter-space, approximately 4.0-6.0nm wide. We report our structural study of the S-layer by electron crystallographic techniques. Image analysis and thin sections of the S-layer treated with and without triton disclosed that retention of the single layer crystal requires the presence of detergent to avoid hydrophobic bonding.

• Journal of Sensor Science and Technology
• /
• v.23 no.4
• /
• pp.234-237
• /
• 2014

In this paper, a copper foil-thick grapheme (thin graphite sheet)-copper foil structure is reported to achieve mechanically strong and high thermal conductive layer suitable for heat spreading components. Since graphene provides much higher thermal conductivity than copper, thick graphene embedded copper layer can achieve higher effective thermal conductivity which is proportional to graphene/copper thickness ratio. Since copper is nonreactive with carbon material which is graphene, chromium is used as adhesion layer to achieve copper-thick graphene-copper bonding for graphene embedded copper layer. Both sides of thick graphene were coated with chromium as an adhesion layer followed by copper by sputtering. The copper foil was bonded to sputtered copper layer on thick graphene. Angstrom's method was used to measure the thermal conductivity of fabricated copper-thick graphene-copper structure. The thermal conductivity of the copper-thick graphene-copper structures is measured as $686W/m{\cdot}K$ which is 1.6 times higher than thermal conductivity of pure copper.

• Korean Journal of Poultry Science
• /
• v.24 no.1
• /
• pp.39-44
• /
• 1997

Two experiments were carried out to determine the effects of pelleting layer diets on the laying perforrnance and nutrients utilizability, using either 50-wk-old(Experiment 1) or 80-wk-old (Experiment 2) layers. There was no effect of pelleting layer diets on hen-day egg production and average egg weight but decreased (P<0.05) feed conversion ratio(intake /egg weight) in both experiments. Although both egg specific gravity and eggshell thickness were not influenced by pelleting eggshell breaking strength was improved(P<0.05) only in Experiment 1. Utilizability of dietary fat was improved(P<0.05) by pelleting layer diets with no difference in other nutrients utilizability. There was no difference in the passage rate of mash and pelleted layer diets.

• Journal of Institute of Convergence Technology
• /
• v.5 no.2
• /
• pp.21-25
• /
• 2015

This paper proposes a fabrication process of deposited layer with micro patterns that uses a combination of a pulsed laser beam machining and an electrodeposition. This process consists of the electrodeposition and the laser beam machining. The deposited layer on metal can be selectively eliminated by laser ablation. As a result, the deposited layer with micro patterns can be fabricated without a mask. The characteristics of the deposited layer on stainless steel were investigated according to the average power and marking speed in the pulsed laser beam machining. The optimal laser beam conditions for precise micro patterning of the deposited layer were determined. Finally, the deposited copper layer with micro text was successfully fabricated by the pulsed laser beam machining.