• Journal of ILASS-Korea
• /
• v.6 no.4
• /
• pp.14-21
• /
• 2001

Rotary atomizer is widely used in practical application ranging from combustion, cooling, spray drying, agriculture, chemical system. Rotary cup atomizer has some advantages such as extreme versatility and liquid atomization successfully varying widely in viscosity. In rotary atomization, the feed liquid is centrifugally accelerated to high velocity and the liquid extends over the rotating surface as a thin film before being discharged into an atmosphere. The degree of rotary atomization depends upon peripheral speed, feed rate, liquid properties and atomizer design. An important asset is that thickness and uniformity of the liquid sheet can readily be controlled by regulating the liquid flow rate and the rotational speed. LDPA(Laser Diffraction Particle Analyser) and image aquisition system are used to measure drop size distribution and spray pattern. The atomization characteristics of the rotary cup atomizer is investigated experimentally by varing the liquid feed rate, rotary cup speed and air velocity for atomization. As a results, the effect of air velocity on the atomization characteristics such as drop size and spray uniformity is considerably greater than variation of those with liquid feed rate.

• Journal of the Optical Society of Korea
• /
• v.14 no.2
• /
• pp.127-130
• /
• 2010

We have developed an efficient electron beam (e-beam) source, a microcolumn, that can be used as a source module for of microscopy and its applications. To obtain a low operating voltage, a very sharp cold field electron emitter was developed by electrochemically etching a tungsten wire. Laser diffraction was used for the fabrication of high-quality electron lenses and for their precise alignment. The measurement of the e-beam currents, and SEM images captured by the microcolumn confirmed the potential of the device as a very good e-beam source.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.5
• /
• pp.566-571
• /
• 1988

Laser scanning system using a hologram is simpler in optical system, lower in cost than using a polygon. In this paper, a thick hologram is fabricated for the underfilled transmission disk type with a merit of wabble insensitivity to vibration. High diffraction efficiency over 50% is obtained using silver halide recording material. The two-dimensional scan pattern with 13 scan-line is made by 7-facet hologon and mirror system. This system can be practically applied to POS(Point of Sale) bar-code symbol reader.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1858-1860
• /
• 1999

To fabricate superconducting multiplexers with narrow pass band characteristics and reduce the physical size of device, we have designed multiplexer using hair-pin type filters with the center frequency of 13.6 GHz. Multiplexers have been fabricated superconductor(HTS), because It has low surface resistance. The $YBa_2Cu_3O_{7-{\delta}}$(YBCO) films were deposited on MgO substrates$(20{\times}20{\times}0.5mm^3)$ by using pulsed laser deposition and conventional photo-lithographic methods were used to pattern the multiplexer. Epitaxial YBCO films were grown on(100) MgO substrates and showed strongly c_axis orientations observed by X-ray diffraction technique. Superconducting transition temperatures were measured to be about 89K. Simulated results of superconducting multiplexer consisting of hair-pin type filters show the insertion loss of about 1.2dB. The measured frequency response will be compared with the simulated results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1539-1542
• /
• 2005

Self-assembled monolayers (SAMs) formed by the adsorption of alkanethiols, $HS(CH_2)_nX$, where X is an organic functional group, onto gold surfaces have attracted widespread interest as templates for the fabrication of molecular and biomolecular microstructures. Previously photopatterning has been thought of as being restricted to the micron scale, because of the wellknown diffraction limit. So, we have explored a novel approach to nanofabrication by utilizing a femtosecond laser coupled to a near-field scanning optical microscope (NSOM).

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.109-116
• /
• 2003

Amorphous GaN Quantum dots(a-GaN QDs) with particle diameters less than bohr radius(~11nm) were successfully fabricated at room temperature by a laser ablation of high densified GaN target. Transmission electron microscopy, SAED diffraction pattern and X-ray photoelectron spectroscopy confirmed the presence of a-GaN QDs with particle size of 7.9, 6.9, 4.4nm under the Ar gas pressures of 50, 100 and 200 Pa, respectively. The room temperature PL and absorbance spectra showed a strong band emission centered at 3.9 eV in a-GaN QDs made under the gas pressures of 100 and 200 Pa, which is nearly 0.5eV blueshifted with respect to the bulk crystal band gap.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.1
• /
• pp.34-37
• /
• 2004

Amorphous chalcogenide thin films, especially a-(Se, S) based films, exhibit a number of photo-induced phenomena. In this study, we make the As$\_$40/Ge$\_$10/Se$\_$15/S$\_$35//Ag thin film and then we measure the holographic diffraction efficiency according to thickness of Ag. And we form the two-dimensional holographic grating. At first, we formed one-dimensional grating and then we form two-dimensional grating by rotate the sample. We found out the most suitable thickness of Ag and in case of As$\_$40/Ge$\_$10/Se$\_$15/S$\_$35//Ag(600${\AA}$), the diffraction efficiency was more higher than other samples. The holographic grating was formed by He-Ne laser(λ=632.8nm). The intensity of incident beam was 2.5mW and incident angle was 20$^{\circ}$. We confirm. the two-dimensional holographic grating by the pattern of diffracted beam and AFM(Atomic Force Microscope) image. We perform the etching process using by 0.26N NaOH in order to confirm clearly two-dimensional grating.

• Journal of Broadcast Engineering
• /
• v.24 no.3
• /
• pp.452-462
• /
• 2019

A digital hologram, which is one of the next generation visual systems, can be generated and displayed in various formats, and a digital hologram is created in accordance with the characteristics of the system for display. Diffraction efficiency can be used as a measure of the characteristics of digital holograms generaged under various conditions in various display environments. In this paper, diffraction efficiency for computer-generated hologram (CGH) under various conditions was measured. This paper discusses the generation conditions that should be considered in hologram display. We compared each condition by measuring the intensity of the first order diffraction pattern of the fringe generated under the Fresnel condition for the phase hologram. Through this paper, we showed the tend about characteristics of the diffraction efficiency according to object point, reconstruction distance, laser and SLM.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.1
• /
• pp.16-24
• /
• 1992

Moire interferometry using a diffraction grating and a laser is a powerful technique for analizing small deformation of a specimen. In the method, the x and y-directional fringe patterns are obtained by using the x and y-directional sets of two beams. If the both sets of two beams are simultaneously incident to the specimen, the x and y-directional fringe patterns are super imposed. In this case, it is difficult to separate each directional fringe pattern. Therefore each fringe pattern has been separately recorded by selecting each set of two beams. In order to analyze a two-dimensional strain changing with time, Moire interferometry using the two-dimensional fourier transform method is proposed and the x and y-directional fringes are separated. By this method, the thermal deformation of a glass plate is analyzed.