• Journal of Broadcast Engineering
• /
• v.12 no.4
• /
• pp.360-372
• /
• 2007

We propose a fast inter-layer mode decision method by utilizing coding information of base layer upward its enhancement layer inscalable video coding (SVC), also called MPEG-4 part 10 Advanced Video Coding Amendment 3 or H.264 Scalable Extension (SE) which is being standardized. In this paper, when the motion vectors from the base layer have zero motion (0, 0) in inter-layer motion prediction or the Integer Transform coefficients of the residual between current MB and the motion compensated MB by the predicted motion vectors from the base layer are all zero, the block mode of the corresponding block to be encoded at the enhancement layer is determined to be the $16{\times}16$ mode. In addition, if the predicted mode of the MB to be encoded at the enhancement layer is not equal to the $16{\times}16$ mode, then the rate-distortion optimization is only performed on the reduced candidated modes which are same or smaller partitioned modes. Our proposed method exhibits the complexity reduction in encoding time up to 72%. Nevertheless, it shows negligible PSNR degradation and bit rate increase up to 0.25dB and 1.73%, respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.4
• /
• pp.61-71
• /
• 2003

On the soft soil consisted of silty clay, the compulsion replacement method is useful for revetment and its safety is very much affected by compulsion replacement depth. Usual method calculating the compulsion replacement depth on silty clay is considered the bearing capacity of soft soil with undrained shear strength increase from ground surface and weight of revetment. But according to soil deposit, there are some cases of soft soil with inter sand layer or clayed silt, which affect the compulsion replacement depth. In this paper, the compulsion replacement depth on soft soil with inter sand layer is analyzed by layered weighted average bearing capacity considering influence effect of Perloff et al.(1967) and compared with numerical method(FLAC). In the result, the calculated depth from numerical method is nearest to layered weighted average bearing capacity in case that contact width under revetment is $0.2B_o$(soft soil with inter sand layer), $0.5B_o$(only soft soil) and the effect of contact width under revetment is less than undrained shear strength, thickness and location of inter sand layer. Also the compulsion replacement depth is as much as the inter sand thickness($d_2/B_o$) is thinner, the inter sand layer location($d_1/B_o$) is farther, and undrained shear strength is less.

• Journal of Broadcast Engineering
• /
• v.24 no.3
• /
• pp.401-410
• /
• 2019

In this paper, we propose a reference picture generation method for Inter-layer prediction based deep learning to improve the SHVC coding performance. A description will be given of a structure for performing filtering using a VDSR network on a DCT-IF based upsampled picture to generate a new reference picture and a training method for generating a reference picture between SHVC Inter-layer. The proposed method is implemented based on SHM 12.0. In order to evaluate the performance, we compare the method of generating Inter-layer predictor by applying dictionary learning. As a result, the coding performance of the enhancement layer showed a bitrate reduction of up to 13.14% compared to the method using dictionary learning, a bitrate reduction of up to 15.39% compared to SHM, and a bitrate reduction of 6.46% on average.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.3
• /
• pp.66-73
• /
• 2019

Recently, FDM-type 3D printer technology has been developed, and efforts have been made to improve the output formability and characteristics further. Through this, 3D printers are used in various fields, and printer technologies are suggested according to usage, such as FDM, SLA, DLP, and SLM. In particular, the FDM method is the most widely used, and the FDM method technology is being developed further. The characteristics of the output are produced by the FDM-type 3D printer, which is determined by various factors, and particularly the perspective of the Inter-Layer Fill Factor, which is the volume ratio of the laminated material that exerts a direct influence. In this study, the Inter-Layer Fill Factor is theoretically obtained by presenting the internal space between each layer according to the laminate thickness as a cross-sectional shape model, and the cross section of the actual laminated sample is compared with the theoretical model through experiments. Then, the equation for the theoretical model is defined, and the strength change according to each condition (tensile strength of material, reduction slope, strength reduction rate, and output strength) is confirmed. In addition, we investigated the influence on the correlation and strength between laminate thickness and the Inter-Layer Fill Factor.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.591-597
• /
• 2012

For heat exchanger applications, 2-ply clad materials were fabricated by rolling of aluminum (Al) and mild steel sheets. Effects of annealing temperature on interface properties, especially on inter-layer formation and softening of strain hardened mild-steel, for Al/mild steel clad materials, were investigated. To obtain optimum annealing conditions for the Al/mild steel clad materials, annealing temperature was varied from room temperature to $600^{\circ}C$. At the annealing temperature about $450^{\circ}C$, an inter-layer was formed in an island-shape at the interface of the Al/mild steel clad materials; this island expanded along the interface at higher temperature. By analyzing the X-ray diffraction (XRD) peaks and the energy dispersive X-ray spectroscopy (EDX) results, it was determined that the exact chemical stoichiometry for the inter-layer was that of $Fe_2Al_5$. In some samples, an X-layer was formed between the Al and the inter-layer of $Fe_2Al_5$ at high annealing temperature of around $550^{\circ}C$. The existence of an X-layer enhanced the growth of the inter-layer, which resulted in the delamination of the Al/mild-steel clad materials. Hardness tests were also performed to examine the influence of the annealing temperature on the cold deformability, which is a very important property for the deep drawing process of clad materials. The hardness value of mild steel gradually decreased with increasing annealing temperature. Especially, the value of hardness sharply decreased in the temperature range between $525^{\circ}C$ and $550^{\circ}C$. From these results, we can conclude that the optimum annealing temperature is around $550^{\circ}C$ under condition of there being no X-layer creation.

• Journal of Broadcast Engineering
• /
• v.12 no.6
• /
• pp.596-610
• /
• 2007

In order to reduce the complexity of SVC encoding, we introduce a fast mode decision method in the enhancement layers of spatial scalability by selectively performing the inter-layer residual prediction of SVC. The Inter-layer residual prediction coding in Scalable Video Coding has a large advantage of enhancing the coding efficiency since it utilizes the correlation between two residuals from a lower spatial layer and its next higher spatial layer. However, this entails the dramatical increase in the complexity of SVC encoders. The proposed method is to analyze the characteristics of integer transform coefficients for the subtracted signal for two residuals from lower and upper spatial layers. Then it selectively performs the inter-layer residual prediction coding and rate-distortion optimizations in the upper spatial enhancement layer if the SAD values of residuals exceed adaptive threshold values. Therefore, by classifying the residuals according to the properties of integer-transform coefficients only with SAD of residuals between two layers, the SVC encoder can perform the inter-layer residual coding selectively, thus significantly reducing the total required encoding time. The proposed method results in reduction of the total encoding time with 51.5% in average while maintaining the RD performance with negligible amounts of quality degradation.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.4
• /
• pp.43-49
• /
• 2003

This research work has been carried out for finding J-integral in mode II of CFRP(carbon fiber reinforced plastics) laminate plates based on the classical bar theory in dynamic conditions with consideration of the effect of inertia forces, eventually to lead to finding the dynamic inter-layer fracture toughness. Dynamic inter-layer fracture toughness was found by a self-made ENF(End Notched Flexure) experimental apparatus using Split Hopkinson's Bar(SHPB), and also observed the variation of the fracture toughness haying different resin contents and fiber arrangements of CFRP specimen([$0_3^{\circ}/90_3^{\circ}/0_6^{\circ}/90_3^{\circ}/0_3^{\circ}$], [$0_{20}^{\circ}$], [$0_5^{\circ}/90_{10}^{\circ}/0_5^{\circ}$]). As an experimental result, in either cases of quasi-static or dynamic load condition, the critical load and the inter-layer fracture toughness increased sharply depending on the increase of resin contents. Therefore, it could, be concluded that the effect by resin contents is the major factor determining the inter-layer fracture toughness in the CFRP laminate plates.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1310-1312
• /
• 2005

Passivation of organic thin-film transistors (OTFTs) using organic and metal thin-film was presented. Parylene-C and titanium were used as an organic and metal layer, respectively. With the proposed passivation method the degradation of electric parameters of OTFTs was relieved compared with non-passivated devices. Several electric parameters such as on/off current, field-effect mobility, and threshold voltage were shown.

• Journal of Information Display
• /
• v.6 no.2
• /
• pp.16-18
• /
• 2005

Hybrid insulator pentacene thin film transistors (TFTs) are fabricated with thermally grown oxide and cross-linked polyvinylalcohol (PVA) including surface treatment by dilute ploymethylmethacrylate (PMMA) layer on $n^+$ doped silicon wafer. Through the optimization of $SiO_2$ layer thickness in hybrid insulator structure, carrier mobility is increased to more than 35 times than that of the TFT which has only a gate insulator of $SiO_2$ at the same electric field. The carrier mobility of $1.80cm^2$/V-s, subthreshold swing of 1.81 V/decade, and $I_{on}/I_{off}$ current ratio> $1.10{\times}10^5$ are obtained less than -30 V bias condition. The result is one of the best reported performances of pentacene TFTs with hybrid insulator including cross-linked PVA layer as a gate insulator at relatively low voltage operation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.15-18
• /
• 2003

Pentacene OTFTs of $Al_2O_3$ insulator treated with a diluted PMMA were fabricated for the application of the low voltage operation and large area displays. The operation voltage of 15 V and the mobility of 0.35 $cm^2/Vsec$ are obtained even adopting the thick dielectric of 100 nm which was deposited by atomic layer deposition at the temperature of $150^{\circ}C$. The current on-off ratio was $4.1{\times}10^4$ for the OTFTs treated with 9:1 PMMA and good saturation characteristics were obtained as drain voltage increases.