• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.450-456
• /
• 2006

The objectives of this study were to investigate physiological and psychological responses to the rustling sound of Korean traditional silk fabrics and to figure out objective measurements such as sound parameters and mechanical properties determining the human responses. Five different traditional silk fabrics were selected by cluster analysis and their sound characteristics were observed in terms of FFT spectra and some calculated sound parameters including level pressure of total sound (LPT), Zwicker's psychoacoustic parameters - loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z), and sound color factors such as ${\Delta}L\;and\;{\Delta}f$. As physiological signals, the ratio of low frequency to high frequency (LF/HF) from the power spectrum of heart rate variability, pulse volume (PV), heart rate (HR), and skin conductance level (SCL) evoked by the fabric sounds were measured from thirty participants. Also, seven aspects of psychological state including softness, loudness, sharpness, roughness, clearness, highness, and pleasantness were evaluated when each sound was presented. The traditional silk fabric sounds were likely to be felt as soft and pleasant rather than clear and high, which seemed to evoke less change of both LF/HF and SCL indicating a negative sensation than other fabrics previously reported. As fluctuation strength(Z) were higher and bending rigidity (B) values lower, the fabrics tended to be perceived as sounding softer, which resulted in increase of PV changes. The higher LPT was concerned with higher rating for subjective loudness so that HR was more increased. Also, compression linearity (LC) affected subjective pleasantness positively, which caused less changes of HR. Therefore, we concluded that such objective measurements as LPT, fluctuation strength(Z), bending rigidity (B), and compression linearity (LC) were significant factors affecting physiological and psychological responses to the sounds of Korean traditional silk fabrics.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1923-1930
• /
• 2004

This paper presents digital microflow controllers(DMFC), where a fluidic digital-to-analog converter(DAC) is used to achieve high-linearity, fine-level flow control for applications to precision biomedical dosing systems. The fluidic DAC, composed of binary-weighted flow resistance, controls the flow-rate based on the ratio of the flow resistance to achieve high-precision flow-rate control. The binary-weighted flow resistance has been specified by a serial or a parallel connection of an identical flow resistor to improve the linearity of the flow-rate control, thereby making the flow-resistance ratio insensitive to the size uncertainty in flow resistors due to micromachining errors. We have designed and fabricated three different types of 4-digit DMFC: Prototype S and P are composed of the serial and the parallel combinations of an identical flow resistor, while Prototype V is based on the width-varied flow resistors. In the experimental study, we perform a static test for DMFC at the forward and backward flow conditions as well as a dynamic tests at pulsating flow conditions. The fabricated DMFC shows the nonlinearity of 5.0% and the flow-rate levels of 16(2$^{N}$) for the digital control of 4(N) valves. Among the 4-digit DMFC fabricated with micromachining errors, Prototypes S and P show 27.2% and 27.6% of the flow-rate deviation measured from Prototype V, respectively; thus verifying that Prototypes S and P are less sensitive to the micromachining error than Prototype V.V.

• Korean Journal of Medicinal Crop Science
• /
• v.24 no.4
• /
• pp.271-276
• /
• 2016

Background: In the present study, we established an HPLC (high performance liquid chromatography)-analysis method for the determination of marker compounds as a part of the material standardization for the development of health-functional foods from Salvia plebeia R. Br. extract. Methods and Results: The quantitative determination method of hispidulin as a marker compound was optimized by HPLC analysis using a YMC hydrosphere C18 column with a gradient elution system. This method was validated using specificity, linearity, accuracy, and precision tests. It showed a high linearity in the calibration curve with a coefficient of correlation ($r^2$) of 0.999995. The method was fully validated, and was sensitive, with the limit of detection (LOD) at $0.09{\mu}g{\cdot}m{\ell}^{-1}$ and limit of quantification (LOQ) at $0.27{\mu}g{\cdot}m{\ell}^{-1}$. The relative standard deviation (RSD) values of the data from intra- and inter-day precision were 0.05 - 0.22% and 0.32 - 0.42%, respectively, and the intra- and inter-day accuracy of hispidulin were 99.5 - 102.3% and 98.8 - 101.5%, respectively. The average content of hispidulin in Salvia plebeia R. Br. extract was $3.945mg{\cdot}g^{-1}$ (0.39%). Conclusions: These results suggest that the developed HPLC method is very efficient, and that it could contribute to the quality control of Salvia plebeia R. Br. extracts as a functional ingredient in health functional foods.

• The Korean Journal of Food And Nutrition
• /
• v.33 no.4
• /
• pp.390-398
• /
• 2020

The purpose of this study was to determine the contents of water-soluble vitamins B₁ (thiamine), B₂ (riboflavin), B₃ (niacin) and B₁₂ (cyanocobalamin) in seafood-based dishes by using the high-performance liquid chromatography with the ultra violet and fluorescence detector. The vitamin B₁, B₂, B₃ and B₁₂ contents were analyzed in 29 seafood-based dishes. The method validation was performed on the method to determine the linearity, accuracy, limits of quantification, limits of detection and precision for vitamin B₁, B₂, B₃ and B₁₂. An excellent linearity range (R²=0.999~1.000) in the calibration curve for the water-soluble vitamins was observed. All analytical methods for the water-soluble vitamins showed the acceptable accuracy (89.4~119.7% recovery) and the precision (0.6~4.8% repeatability and 1.0~4.2% reproducibility). The highest content of vitamin B₁ was 2.646 mg/100 g in the kkongchi-jorim, and the highest contents of vitamin B₂, B₃ and B₁₂ were 0.370 mg/100 g, 10.971 mg/100 g, and 17.193 ㎍/100 g, respectively, in the kkongchi-gui. Our results provide reliable data on the contents of the water-soluble vitamins of seafood-based dishes in Korea.

• Korean Journal of Environmental Agriculture
• /
• v.32 no.2
• /
• pp.128-135
• /
• 2013

BACKGROUND: This study was performed to develop a single residue analytical method for new herbicide metazosulfuron in crops. METHODS AND RESULTS: Brown rice, apple, mandarin, Kimchi cabbage and soybean were selected as representative crops, and clean-up system, partition solvent and extraction solvent were optimized. Instrumental limit of quantitation (ILOQ), linearity of calibration curve and method limit of quantitation (MLOQ) were determined based on the chromatography and whole procedures. For recovery tests, brown rice, apple, mandarin, Kimchi cabbage and soybean samples were macerated and fortified with metazosulfuron standard solution at three levels (MLOQ, 10 MLOQ and 100 MLOQ). And then those were extracted with acetonitrile, concentrated, and partitioned with ethyl acetate. Then the extracts were concentrated again and cleaned-up through $NH_2$ (aminopropyl) SPE cartridge with acetone : dichloromethane (1% acetic acid) (20 : 80, v/v) before concentration and analysis with HPLC. CONCLUSION(S): ILOQ of metazosulfuron was 2 ng (S/N${\geq}$10) and good linearity was achieved between 0.05 and 12.5 mg/Kg of metazosulfuron standard solutions, with coefficients of determination of 0.9999. MLOQ was 0.02 mg/Kg. Good recoveries from 74.1 to 116.9% with coefficients of variation (C.V.) of less than 10% were obtained, regardless of sample type, which satisfies the criteria of Korea Food and Drug Administration (KFDA). Those results were reconfirmed with LC-MS (SIM). The method established in this study is simple, economic and efficient to be applied to most of crops as an official and general method for residue analysis of metazosulfuron.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.2
• /
• pp.422-427
• /
• 2005

In this paper, Doherty amplifier is designed by the need of improving the linearity and efficiency of wireless network and repeater for WCDMA. It is designed to maintain the high linearity and efficiency at the low efficiency period of the power amplifier after analyzing Doherty technique using the active load-pull in condition of the high efficiency power amplifier implementation according to the variation of input power. CW 1-tone experimental results at the WCDMA frequency 2.11$\~$2.17 CHz shows that Doherty amplifier, which achieves pore. add efficiency(PAE) 50$\%$ at 6dB back off the point from maximum output power 52.3dBm, obtains higher efficiency of 13.3$\%$ than class AB. finding optimum bias point after adjusted gate voltage, Doherty amplifier shows that IMD3 improves 4dB.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.2
• /
• pp.37-42
• /
• 2000

In this paper, The high-speed, low-Power analog-to-digital conversion structure is proposed using the pipelined comparator away for high-speed conversion rate and the successive- approximation structure for low-power consumption. This structure is the successive-approximation structure using pipelined comparator array to change the reference voltage during the holding time. An 8-bit 10MS/s analog-to-digital converter is designed using 0.8${\mu}{\textrm}{m}$ CMOS technology. The INL/DNL errors are $\pm$0.5/$\pm$1, respectively. The SNR is 41㏈ at a sampling rate of 10MHz with 100KHz sine input signal. The Power consumption is 4.14㎽ at 10MS/s.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.242-246
• /
• 2012

This paper presents an integrated low noise and highly linear wideband RF front-end for a digital terrestrial and cable TV tuner, which are used as a part of double-conversion TV tuner. The low noise amplifier (LNA) has a low noise figure and high linearity by adopting a noise canceling technique based on current amplification. The up-conversion mixer and SAW buffer have high linearity by employing a third order intermodulation cancellation technique. The proposed RF front-end is designed in a $0.18{\mu}m$ CMOS and draws 60 mA from a 1.8 V supply voltage. The RF front-end shows a voltage gain of 30 dB, an average single side-band noise figure of 4.2 dB, an IIP2 of 40 dBm, and an IIP3 of -4.5 dBm for the entire band from 48 MHz to 862Hz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.685-691
• /
• 2003

This work describes a 3 V 12b 100 MS/s CMOS digital-to-analog converter (DAC) for high-speed communication system applications. The proposed DAC is composed of a unit current-cell matrix for 8 MSBs and a binary-weighted array for 4 LSBs, considering linearity, power consumption, chip area, and glitch energy. The low-glitch switch driving circuit is employed to improve the linearity and the dynamic performance. Current sources of the DAC are laid out separately from the current-cell switch matrix core. The prototype DAC is implemented in a 0.35 urn n-well single-poly quad-metal CMOS technology. The measured DNL and INL of the prototype DAC are within $\pm$0.75 LSB and $\pm$1.73 LSB, respectively, and the spurious-free dynamic range (SFDR) is 64 dB at 100 MS/s with a 10 MHz input sinewave. The DAC dissipates 91 mW at 3 V and occupies the active die area of 2.2 mm ${\times}$ 2.0 mm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.83-88
• /
• 2002

To increase the device linearities and the breakdown-voltages of FETs, $Al_{0.25}$G $a_{0.75}$As/I $n_{0.25}$G $a_{0.75}$As/A $l_{0.25}$G $a_{0.75}$As partially doped channel FET(DCFET) structures are proposed. The metal insulator-semiconductor(MIS) like structures show the high gate-drain breakdown voltage(-20V) and high linearities. We propose a partially doped channel structure to enhance the device linearity to the homogeneously doped channel structure. The physics of partially doped channel structure is investigated with 2D device simulation. The devices showed the small ripple of the current cut-off frequency and the power cut-off frequency over the wide bias range. bias range.