• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.898-904
• /
• 2017

DFT(Discrete Fourier Transform) is one of the most widely used method to estimate the phasor of a relaying signal. The harmonics are eliminated by the DFT. However, high frequency components, except for harmonics, are not removed and cause an error in DFT-based phasor estimation process. This paper suggests high frequency noise reduction method by using a newly designed low-pass filter to estimate a signal phasor. When selecting a stop-band cut-off frequency of the low-pass filter, high frequency components generated by faults are considered. To reduce the phasor estimation delay caused by a low-pass filter, this paper proposes a low-pass filter whose settling time is reduced. An adverse effect of high frequency noise on DFT-based phasor estimation is reduced. To evaluate the performance of the proposed method, signals which are collected under a fault condition at a 345[kV] transmission system modeled by EMTP-RV are used.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1166-1169
• /
• 2005

This paper describes a new transient voltage suppressor(TVS) with a low insertion loss and a high cut-off frequency to protect antenna circuit from transient voltages. Conventional protection devices have some problems such as a low frequency bandwidth and a high insertion loss. In order to improve these limitations, a coaxal type TVS, which consists of a gas tube is developed. The performance of the proposed transient voltage suppressor is tested by using a combination surge generator specified in IEC 61000-4-5 standard and by using a network analyzer of 40 MHz ${\sim}$ 5 GHz bandwidth. From the experimental results, it is confirmed that the proposed TVS has an enough protection performance in a low insertion loss and a high cut-off frequency.

• Proceedings of the KAIS Fall Conference
• /
• 2004.06a
• /
• pp.172-175
• /
• 2004

This paper analyzes the effects of Ge profiles shape of SiGe heterojunction bipolar transistors (HBT's) for high frequency application. Device simulations using ATLAS/BLAZE for the SiGe HBT with trapezoidal or triangular Ge profile are carried out to optimize the device performance. An HBT with $15\%$ triangular Ge profile shows higher cut-off frequency and DC current gain than that with $19\%$ trapezoidal Ge profile. The cut-off frequency and DC gain are increased from 42GHz to 84GHz and from 200 to 600, respectively. The SiGe HBT has been fabricated using a production CVD reactor.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.5 s.98
• /
• pp.19-28
• /
• 1999

In this study, a real-time simulation system and a washout algorithm for an excavator have been developed for a driving simulator with six degrees of freedom. The excavator model consisting of a boom. bucket, upper frame, lower frame and four wheels, has total 11 degrees of freedom. The suggested washout algorithm consists of high and low pass filters with second order. The high pass filters cut off low frequency of the motion cues limited by platform motion. The cut off frequency for the tilt coordination are suggested for a realistic regeneration of excavator motion.

• Journal of IKEEE
• /
• v.16 no.2
• /
• pp.116-120
• /
• 2012

We reported on a high performance InGaAs/InAlAs metamorphic HEMT with 50 nm gate length on a GaAs substrate. The fabricated $50nm{\times}60{\mu}m$ MHEMT showed good DC and RF characteristics. Typical drain current density of 740 mA/mm and extrinsic transconductance(gm) of 1.02 S/mm were obtained with our devices. The current gain cut-off frequency(fT) and maximum oscillation frequency(fmax) obtained for the fabricated MHEMT device were 430 GHz and 406 GHz, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.809-812
• /
• 2001

We were fabricated of NiCr thin film resistors on A1$_2$O$_3$and SiO$_2$/Si substrates by dc magnetron sputtering system. The AC characteristics of resistors were studied. The cut-off frequency were found >10 MHz for the resistors with 39 ohm value of Alumina substrates, but the cut-off frequency were found 400 kHz for the resistors with 168 ohm value of SiO$_2$/Si substrates. In high frequency applications, the substrate selection is the most important factor.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.125-130
• /
• 2011

This paper shows a method to design complementary filter using least square. The complementary filter is one of useful filters estimating angle. The basic concept of this filter is to enhance advantages of each sensor that angle detecting using a gyroscope has good accuracy at a high frequency and an accelerometer at a low frequency. When designing complementary filter, the most commonly used method is using cut-off frequency. However, it may be not easy to obtain a cut-off frequency. This paper presents a systematic method to determine the coefficients of the complementary filter using well-known linear least squares minimizing error between estimating angle and true angle.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.32-37
• /
• 1984

In this paper, a practical and simple scheme is described for the implementation of a moving average filter which is known to be able to provide low pass filter characteristics, and the estimated cut off frequency formulation of the filter and filtering algorithm are presented for the filter design. Some results of an experimental system using the commerical Z-80 microprocessor are given. It shown that high frequency noises are canceled effectively in frequency domain and time domain experiments and that results of the estimated cut off frequency formular is compared with measured one.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1345-1347
• /
• 2008

This paper described a method of determining whether arcing is present in a low-voltage wiring system. We simulated the series arcing that generated in electrical loads and fabricated a arc detection module which can discriminate between normal and arcing state. The module consists of a high-pass filter with a low cut-off frequency of 3 kHz to attenuate power frequency voltage and an active band-pass filter with a frequency of 4 kHz ${\sim}$ 8 kHz to detect series arc signals only. We tested an Incandescent lamp that was controlled by a dimmer and analysed. The module consists of a high-pass filter with a low cut-off frequency of 3 kHz to attenuate power frequency voltage by 80 dB and an active band-pass filter with a frequency of 4 kHz to detect series arc signals only. From the experimental results, we could detect series arc signals without an influence of non-linear loads.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1835-1837
• /
• 2004

The UHF electromagnetic waves excited by PD pulses propagate along the GIS busbar not only TEM mode, but also TE and TM mode. Generally the waves detected by the UHF sensors are those of high order modes and such waves can only propagate the higher than cut-off frequency. In this paper, computed cut-off frequency of 362[kV] GIS by each modes and simulated electromagnetic field of each propagation modes by FEM(Finite Element Method) program. Frequency band of each TEmn/TMmn modes were determinated by simulation results and were discussed optimal position of UHF sensor from this results.