• Korean Journal of Materials Research
• /
• v.15 no.9
• /
• pp.577-584
• /
• 2005

Thin Ni-B layer, $1{\mu}m$ thick, was electrolessly deposited on Cu electrode fabricated by electro-deposition. The purpose of the layer is to encapsulate Cu electrodes for preventing Cu oxidation and to serve as a diffusion barrier. The layers were annealed at $580^{\circ}C$ with and without pre-annealing at $300^{\circ}C$ for . 30minutes. In the layer with pre-annealing, the amount of Cu diffusion was lower about 5 times than the layer without pre-annealing. The difference in Cu concentration may be attributed to $Ni_3B$ formation prior to Cu diffusion. However, the difference in Cu concentration decreased during the annealing time of 5 h due to the grain growth of Ni.

• Korean Journal of Materials Research
• /
• v.18 no.2
• /
• pp.107-111
• /
• 2008

[ $BaO{\cdot}Nd_2O_3{\cdot}5TiO_2$ ] (BNT) ceramics modified with a borate glass containing Ba, Nd and Ti as glass constituents were investigated with regard to their sintering behavior and microwave dielectric properties. An addition of iso-component glass significantly improved the sinterabilty of the BNT ceramics and lowered the sintering temperature. A maximum density of $5.29\;g/cm^3$ and an x-y shrinkage of 17% were obtained for BNT ceramics containing 10wt.% of the glass sintered at $1100^{\circ}C$. The dielectric composition without the glass additive was only slightly densified at $1100^{\circ}C$. The resulting sample exhibited two crystalline phases, $BaNd_2Ti_5O_{14}$ and $Ba_2Ti_9O_{20}$, regardless of sintering temperature and glass content. When >10wt.% glass was added, exaggerated grain growth with a less uniform microstructure was found, resulting in the subsequent reduction of the fired density and the dielectric properties. BNT ceramics containing 10wt.% of the isocomponent glass sintered at $1100^{\circ}C$ for 4 h showed promising dielectric properties of k = 71.3 and Q = 1,330.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.3
• /
• pp.279-286
• /
• 1995

As Al-Li based alloys are to find widespread use in aerospace and other structural applications in which their low-density high specific stiffness properties be exploited, their mechanical properties must adequately match those of the which they intended to replace. In order to develop these purposed, the precipitation behaviors of the rapidly solidified Al-Li-Ti alloys aged at various temperature were investigated. ${\delta}'$ phase precipitated homogeneously in the matrix during not only melt quenching but also aging at the aging temperature of $160^{\circ}C\;and\;210^{\circ}C$. The addition of the Ti in Al-Li alloy promoted the formation of $\delta$' phase. The addition of Ti on the ${\delta}'$ solvus line had a little effect over the thermodynamics ${\delta}'$ solvus line. The reason for these behavior was that the ${\delta}'$ phase was suppressed to precipitate as much as supercooling by melt quenching. The discontinuous precipitation reaction occurred by the preferential growth of ${\delta}'$ phase due to the migration of grain boundary provided the driving force dependent of solute concentration fluctuations.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.48 no.6
• /
• pp.473-478
• /
• 2003

This study was conducted to clarify the effects of duck free-ranging time on the growth and behavior patterns of duck, pH and dissolved oxygen of irrigation water, and growth and yield of the rice plants in paddy fields. Two paddy fields with each 5 aye were used for 12 hours duck free-ranging plot (12HFR) and 24 hours duck free-ranging plot(24HFR). Body weight gain of the duck was not different between 12HFR and 24HFR. Eating and feather grooming behavior in the 12HFR were significantly longer than those of 24HFR, but other behavior patterns were not so. Working behavior and activities of duck in paddy fields tended to be longer in the 12HFR than in 24HFR. However, any difference was not found on staying time of duck in paddy fields. Although it was not statistically significant, pH and dissolved oxygen of irrigation water tended to be higher in the 12HFR than in 24HFR. The plant height of rice in the 12HFR was significantly shorter than that of 24HFR during the latter half period. The number of tillers per hill was significantly increased in the 24HFR than in 12HFR. The shoot dry weight of rice in the 12HFR was significantly less than in the 24HFR during the heading stage of rice plant, but the root dry weight was not different. The number of spikelets per panicle was significantly less in the 12HFR than in 24HFR, however the percentage of ripened grains was significantly higher in the 12HFR. The yield of rice was not significantly different between the treatments. In conclusion, the free-ranging time of duck for 12 hours in paddy fields promoted eating and working behavior of the ducks. Free-ranging time did give effects on rice traits such as the number of tillers per hill, plant height, shoot dry weight of the rice plant, and spikelet number and percentage of ripened grain. However, the duck growth, pH and dissolved oxygen of irrigation water, and paddy rice yield were not affected by duck free-ranging time. These results might suggest that almost same effect as in 24 hours of free-ranging can be obtained with only 12 hours of free-ranging in daytime.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.6
• /
• pp.670-677
• /
• 2012

Perovskite-type oxides such as doped barium zirconate ($BaZrO_3$) show high proton conductivity and chemical stability when they are exposed to hydrogen and water vapour containing atmospheres, thus it can be applicable to the hydrogen separation and the fuel cell electrolyte membranes. However the high temperature ($1700-1800^{\circ}C$) and long sintering times (24h) are generally required to prepare the fully densified $BaZrO_3$ pellets. These sintering conditions lead to the limitation of the grain size growth and the degradation of conductivity due to the acceleration of BaO evaporation at $1200^{\circ}C$. Here we demonstrate NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ with lower calcination and sintering temperature, less experimental procedure and lower process cost than the conventional mixing method. The stoichiometry of $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ was optimized by the control of excess amount of Ba (5mol%) to minimized BaO evaporation. We found that the crystal size of NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ was increased with increase of calcination temperature from XRD analysis. NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ powder was calcined at $1000^{\circ}C$ for 12h when its showed the highest conductivity of $3.3{\times}10^{-2}s/cm$.

• The Journal of Pediatrics of Korean Medicine
• /
• v.13 no.2
• /
• pp.1-39
• /
• 1999

A infancy is the period in that growth and development of man are the most fast and neutrial requirement is the most big on his life. The insufficient neutrition of this period can have bad effect uppon man's whole life health not only physically but also pscychogenically and emotionally. Therefore a proper feeding at a proper time is very important to form the good food behavior and emotional development. The rate of using the commercial weaning food in Korea has gradually increased since 1970 and expected to be more increasing in future. In this paper, I investigate the general weaning status, stneutrial component and material content of infant weaning foods marketing in Korea at present. The material for this study have been collected in the exposition of products and data from manufacturing companies and etc. The conclusion is following. 1. The proper weaning period is from $4{\sim}6$ momth to 12 momth, but recently it is inclined to prolong. 2. In weaning methods, using a spoon is superior to using a bottle in food behavior and neutrial status. 3. The commercial weaning foods have two type, the powder type and formula type, but except gober's, all products marketing in Korea are the powder type and a sort of product is very simple. Therefore it is necessary to develp the more various kind of weaning foods, especially the formula type. 4. In the neutrial component, Son-Sik (flour of grain) cannot be up to international standards and the greater parts of weaning foods have too much suger over the standards.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.11
• /
• pp.979-986
• /
• 2003

Sintering behavior and electrical properties of CeO$_2$ system were investigated as a function of the amount of Gd:$_2$O$_3$, and Sm$_2$O$_3$, addition. Doped CeO$_2$ consisted of a homogeneous solid solution of the cubic fluorite structure within the amount of addition from 0 mol% to 15 mol%. Grain growth rate of Gd$_2$O$_3$-doped CeO$_2$ was much smaller than that of pure CeO$_2$, while densification rate was considerably larger. Thus doped CeO$_2$ showed a higher density than pure CeO$_2$. The electrical conductivity of Ce$_1$-$_{x}$Sm$_{x}$O$_1$-$_{x}$/2 was increased up to x = 0.2. However, with further increasing dopant concentrations, the magnitude of the conductivity was found to decrease remarkably. The ionic conductivity value obtained at $700^{\circ}C$ for 10 mol% Sm$_2$O$_3$-doped CeO$_2$ electrolyte was 4.6${\times}$10$^{-2}$ S$.$$cm^{-1}$ /.EX> /.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.3
• /
• pp.128-132
• /
• 2007

[ $B_4C$ ] ceramics were fabricated by spark plasma sintering process and their sintering behavior, microstructure and mechanical properties were evaluated. Relative density of $B_4C$ ceramics were obtained by spark plasma sintering method reached as high as 99% at lower temperature than conventional sintering method, in addition, without any sintering additives. The mechanical properties of $B_4C$ ceramics was improved by a methanol washing process which can be removed $B_2O_3$ phase from a $B_4C$ powder surface. This improvement results ken the formation of homogeneous microstructure because the grain coarsening was suppressed by the elimination of $B_2O_3$ phase. Particularly, fracture toughness of the sintered specimen using a methanol washed powder improved over 30% compared with the specimen using an as-received commercial powder.

• Bulletin of the Korean Chemical Society
• /
• v.5 no.2
• /
• pp.73-78
• /
• 1984

Superplastic alloys generally exhibit a three-stage sigmoidal variation of stress (f) with strain rate (s), the stages being named region 1, 2 and 3 according to the increasing order of stress or strain rate. In the recent years, two different types of papers have been published on the plastic deformation of Zn-22% Al eutectoid in region Ⅰ differing in strain-rate sensitivity m (= dln f/dln s). In this paper, the data of the two groups have been analysed by applying Kim and Ree's theory of superplastic deformation. (1) We obtained the parametric values of $X_{gj}/{\alpha}_{gj}\;and\;{\beta)_{gj}$ (g: grain boundary, j = 1,2 indicating flow units) appearing in Kim and Ree's theory [Eq. (2a)]. (2) It was found that the value of $X_{g^2}/{\alpha}_{g^2}$ is small for the group data with small m, i.e., ${\alpha}_{g^2}$, which is proportional to the size of flow unit g2, is large whereas ${\alpha}_{g^2}$ is small for the groups data with large m, i.e., the size of the flow unit g2 is small. In other words, the two types of behavior occur by the size difference in the flow units. (3) From the ${\beta}_{gj}$ value, which is proportional to the relaxation time of flow unit gj, the ${\Delta}H_{gj}^{\neq}$ for the flow process was calculated, and found that ${\Delta}H_{g^2}^{\neq}$ is large for the group data with small m whereas it is small for the group data with large m. (4) The flow-unit growth was studied, but it was concluded that this effect is not so important for differentiating the two groups. (5) The difference in ${\alpha}_{g^2}$ and in the growth rate of flow units is caused by minute impurities, crystal faults, etc., introduced in the sample preparation.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.67-71
• /
• 2021

In this study, graphene layer was grown on metal microwire using chemical vapor deposition. The difference of carbon solubility between copper and nickel resulted in the formation of mono-layer and multi-layer graphene were formed on the surfaces of copper and nickel microwires, respectively. During the growth of graphene at high temperature, copper and nickel were recrytallized and the grain size increased. The ampacity of graphene/copper microwire was improved by approximately 27%, 1.91×105 A/㎠, compared to pristine copper microwire. Similar to this behavior, the ampacity of multilayer graphene/nickel microwire was 4.41×104 A/㎠ which is about about 36% improved compared to the pure nickel microwire. The excellent electrical properties of graphene/metal composites are beneficial for supplying the electrical energy to the high-power electronic devices and equipment.