• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1373-1376
• /
• 1998

Electroluminescent(EL) devices based on organic materials have been of great interest due to their possible applications for large-area flat-panel displays. They are attractive because of their capability of multicolor emission, and low operation voltage. In this study, glass substrate/ITO/TPD/$Eu(TTA)_3(phen)/Alq_3/Al$ structures were fabricated by evaporation method, where aromatic diamine(TPD) were used as a hole transporting material, $Eu(TTA)_3(phen)$ as an emitting material, and tris(8-hydroxyquinoline)Aluminum ($Alq_3$) as an electron transporting layer. Electroluminescent(EL) and I-V characteristics of $Eu(TTA)_3(phen)$ with a variety thickness was investigated. This structure shows the red EL spectrum, which is almost the same as the PL spectrum of $Eu(TTA)_3(phen)$. I-V characteristics of this structure show that turn-on voltage was 9V and current density of $0.01A/cm^2$ at a dc drive voltage of 9V. Details on the explanation of electrical transport phenomena of these structures with I-V characteristics using the trapped-charge-limited current model will be discussed.

• 한국전기전자재료학회논문지
• /
• 제28권3호
• /
• pp.185-190
• /
• 2015

In this study, we fabricated the indium gallium zinc oxide (IGZO), zinc oxide (ZnO), aluminum zinc oxide (AZO). oxide and silver are deposited by magnetron sputtering and thermal evaporator, respectively transparency and energy bandgap were changed by the thickness of silver layer. To fabricate metal oxide metal (OMO) structure, IGZO sputtered on a corning 1,737 glass substrate was used as bottom oxide material and then silver was evaporated on the IGZO layer, finally IGZO was sputtered on the silver layer we get the final OMO structure. The radio-frequency power of the target was fixed at 30 W. The chamber pressure was set to $6.0{\times}10^{-3}$ Torr, and the gas ratio of Ar was fixed at 25 sccm. The silver thickness are varied from 3 to 15 nm. The OMO thin films was analyzed using XRD. XRD shows broad peak which clearly indicates amorphous phase. ZnO, AZO, OMO show the peak [002] direction at $34^{\circ}$. This indicate that ZnO, AZO OMO structure show the crystalline peak. Average transmittance of visible region was over 75%, while that of infrared region was under 20%. Energy band gap of OMO layer was increased with increasing thickness of Ag layer. As a result total transmittance was decreased.

• 한국전기전자재료학회논문지
• /
• 제25권7호
• /
• pp.543-551
• /
• 2012

In this study, transparent conducting Al-doped Zinc Oxide (AZO) films with a thickness of 150 nm were prepared on corning glass substrate by the RF magnetron sputtering with using a Al-doped zinc oxide (AZO), ($Al_2O_3$: 2 wt%) target at room temperature. This study investigated the effect of rapid thermal annealing temperature and oxygen ambient on structural, electrical and optical properties of Al-doped zinc oxide (AZO) thin films. The films were annealed at temperatures ranging from 400 to $700^{\circ}C$ by using Rapid thermal equipment in oxygen ambient. The effect of RTA treatment on the structural properties were studied by x-ray diffraction and atomic force microscopy. It is observed that the Al-doped zinc oxide (AZO) thin film annealed at $500^{\circ}C$ at 5 minute oxygen ambient gas reveals the strongest XRD emission intensity and narrowest full width at half maximum among the temperature studied. The enhanced UV emission from the film annealed at $500^{\circ}C$ at 5 minute oxygen ambient gas is attributed to the improved crystalline quality of Al-doped zinc oxide (AZO) thin film due to the effective relaxation of residual compressive stress and achieving maximum grain size.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.353-353
• /
• 2008

Carbon nanotubes (CNTs) are attractive for field emitter because of their outstanding electrical, mechanical, and chemical properties. Several applications using CNTs as field emitters have been demonstrated such as field emission display (FED), backlight unit (BLU), and X-ray source. In this study, we fabricated a CNT cathode using transparent ultra-thin CNT film. First, CNT aqueous solution was prepared by ultrasonically dispersing purified single-walled carbon nanotubes (SWCNTs) in deionized water with sodium dodecyl sulfate (SDS). To obtain the CNT film, the CNT solution in a milliliter or even several tens of micro-litters was deposited onto a porous alumina membrane through vacuum filtration process. Thereafter, the alumina membrane was solvated by the 3 M NaOH solution and the floating CNT film was easily transferred to an indium-tin-oxide (ITO) glass substrate of $0.5\times0.5cm^2$ with a film mask. The transmittance of as-prepared ultra-thin CNT films measured by UV-Vis spectrophotometer was 68~97%, depending on the amount of CNTs dispersed in an aqueous solution. Roller activation, which is a essential process to improve the field emission characteristics of CNT films, increased the UV-Vis transmittance up to 93~98%. This study presents SEM morphology of CNT emitters and their field emission properties according to the concentration of CNTs in an aqueous solutions. Since the ultra-thin CNT emitters prepared from the solutions show a high peak current density of field emission comparable to that of the paste-base CNT emitters and do not contain outgassing sources such as organic binders, they are considered to be very promising for small-size-but-high-end applications including X-ray sources and microwave power amplifiers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.329-329
• /
• 2008

To date, rubbing has been widely used to align LC molecules uniformly. Although rubbing can be simple, it has fundamental problems such as the generation of defects by dust and static electricity, and difficulty in achieving a uniform LC alignment on a large substrate. Therefore, noncontact alignment has been investigated. Ion beam induced alignment method, which provides controllability, nonstop process, and high resolution display. In this study, we investigated liquid crystal (LC) alignment with ion beam (IB) that non contact alignment technique on polyimide and electro-optical characteristics of twisted nematic (TN)-liquid crystal display (LCD) on the poly imide under various ion beam angles. In this experiment, Polyimide layer was coated on glass by spin-coating and Voltage-transmittance(VT) and response time characteristics of the TN cell were measured by a LCD evaluation system. The good characteristics of the nematic liquid crystal (NLC) alignment with the ion beam exposure poly imide surface was observed. The tilt angle of NLC on the PI surface with ion beam exposure can be measured under $1^{\circ}4 for all of irradiation angles. In addition, it can be achieved the good ED properties, and residual DC property of the ion beam aligned TN cell on polyimide surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.456-456
• /
• 2008

In the past few years, the deposition and characterization of cadmium sulfide semiconducting thin films has received a considerable amount of interest due to their potential application in the area of electronic and opto-electronic devices fabrications. Polycrystalline CdS thin films posses good optical transmittance, wide band-gap and electrical properties makes it as one of the ideal material for their application to solar cell fabrication. Cadmium sulfate thin films were deposited by the chemical bath deposition method using tartaric acid and triethanolamine as a complexing agent. Deposition parameters such as pH, temperature, deposition time and concentration of the reactant species were optimized so as to obtain reflecting, good adherent uniform thin films on the glass substrate. Reaction mechanism of the thin film formation is also reported. The crystallographic structure and the crystallite size were studied by the X-ray diffraction pattern. The optical band-gap of deposited film is identified by measuring the transmittance in the visible region. Temperature dependence of resistivity confirmed the semiconducting behavior of the film. Scanning electron micrographs (SEM) showed the presence of grain particles of size 50 nm.

• 한국전기전자재료학회논문지
• /
• 제30권12호
• /
• pp.806-811
• /
• 2017

An all-transparent ultraviolet (UV) photodetector was fabricated by structuring $p-NiO/n-SnO_2/ITO$ on a glass substrate. $SnO_2$ is an important semiconductor material because of its large bandgap, high electron mobility, high transmittance (as high as 80% in the visible range), and high stability under UV light. For these reasons, $SnO_2$ is suitable for a range of applications that involve UV light. In order to form a highly transparent p-n junction for UV detection, $SnO_2$ was deposited onto a device containing NiO as a high-transparent metal conductive oxide for UV detection. We demonstrated that all-transparent UV photodetectors based on $SnO_2$ could provide a definitive photocurrent density of $4nA\;cm^{-2}$ at 0 V under UV light (365 nm) and a low saturation current density of $2.02nA{\times}cm^{-2}$. The device under UV light displayed fast photoresponse with times of 31.69 ms (rise-time) and 35.12 ms (fall-time) and a remarkable photoresponse ratio of 69.37. We analyzed the optical and electrical properties of the $NiO/SnO_2$ device. We demonstrated that the excellent properties of $SnO_2$ are valuable in transparent photoelectric device applications, which can suggest various routes for improving the performance of such devices.

• 전자공학회논문지SC
• /
• 제37권4호
• /
• pp.49-54
• /
• 2000

고분자 이온 감응막을 광도파로로 이용한 새로운 형태의 센서소자를 제작하여 칼슘이온의 농도 변화에 따른 그 특성을 평가하였다. 광도파로 소자는 실리카 유리기판에 기존의 반도체 사진식각법 (photolitho-graphy)을 이용하여 도파로가 형성되어질 부분을 에칭한 후 감지막을 스핀코팅법으로 코팅하여, 그 자체를 도파로로 이용한 고속 응답의 새로운 형태의 센서소자를 제작하였다. 도파로로 사용된 감지막은 칼슘이온에 대해 특이성을 가지는 변색성 이온감응물질인 ETH5294, 중성이온감응물질인 K23El, anionic site인 NaTm(CF/sub 3/)/sub 2/PB, 가소제인 DOP 및 PVC-PVAC-PVA 폴리머를 THF 용매에 녹여 스핀 코팅법으로 제작하였다. 여러 가지 변수에 따른 센서의 특성을 평가하기 위하여 도파로의 두께(즉, 감지막의 두께), 변색성 이온감응물질의 농도, 각 모드 변화에 따른 센서의 감응특성을 비교 평가하였다. 제작된 센서는 칼슘이온에 대해 1×10­6∼1M의 측정 범위를 가지며, 1×10­⁴∼1×10­¹M 영역에서 선형성을 가지며, 기존의 광학적 측정 방법인 분광분석법에 비해 높은 감도를 나타냄을 확인하였다.

• 대한기계학회논문집B
• /
• 제37권2호
• /
• pp.119-124
• /
• 2013

본 연구에서는 전도성 잉크의 레이저 열경화 공정시 은 나노입자 잉크의 레이저 열경화 공정 온도를 수치해석하였다. 유리기판 위에 잉크젯 프린팅을 이용하여 인쇄한 은 나노 입자 잉크를 532 nm 파장의 CW 레이저를 각기 다른 세기로 60 초 동안 조사하여 가열하였다. 온도계산을 위해서, 열생성항에 들어가는 반사율을 구하였고, 레이저 조사 중 실시간 은 나노입자 잉크의 비저항을 측정하였다. 온도 계산은 2차원 열전도 방정식에 Wiedemann-Franz law 를 적용하였다. 그 결과, 레이저 조사로 인해 인쇄된 잉크의 온도가 상승할수록 비저항이 떨어지는 결과를 확인하였다.

• 한국추진공학회지
• /
• 제9권4호
• /
• pp.1-8
• /
• 2005

과산화수소를 단일추진제로 사용하는 마이크로 추력기를 위한 실험적 연구를 수행하였다. 연구에서 은 촉매 활성화 방법과 메조스케일 반응기의 성능평가에 관한 실험을 하였다. 시도한 여러 가지 활성 방법 중, $500^{\circ}C$의 수소 환원법의 경우 가장 좋은 반응성을 가짐을 확인 하였다. 추진제의 완전한 분해 조건을 찾기 위해 메조스케일 반응기가 제작되었다. 촉매 베드를 위해 지지체로 20 mm 길이의 유리 웨이퍼를 준비하여 은 촉매를 스퍼터링 하였다. 과산화수소 공급 유량에 따라 반응기내 공간시간이 변하므로 유량을 변화시키며 반웅기 실험을 수행하였고 전환율을 측정 하였다. 20 mm 베드 길이에서 추진제의 완전한 분해를 위해 480초 이상의 공간시간이 요구된다.