• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.285-286
• /
• 2014

Recently, the unipolar gate power source is preferred in inverter system because of cost reduction reason. In this case, designer uses 0V source for turning-off the switching devices instead of negative voltage at Vee source. If the gate driver circuit has some stray inductance, the gate voltage would happen a surge voltage. This paper analyzes that of stray inductance effect during the switching behavior in the circuit and the proposed solutions were verified by pulse test.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.6
• /
• pp.732-741
• /
• 2018

In order to maximize the usable capacity of a BMS (battery management system) that uses several battery cells connected in series, a cell balancing technique that equips each cell with the same voltage is needed. In the active cell balancing circuit using a multi-winding transformer, a balancing circuit that transfers energy directly to the cell (cell-to-cell) is composed of a PMOS switch and a gate driving chip for driving the NMOS switch. The TLP2748 photocoupler and the TLP2745 photocoupler are required, resulting in increased cost and reduced integration. In this paper, instead of driving PMOS and NMOS switching devices by using photocoupler, we proposed 70V BCD process based PMOS gate driving circuit, NMOS gate driving circuit, PMOS gate driving circuit and NMOS gate driving circuit with improved switching time. ${\Delta}t$ of the PMOS gate drive switch with improved switching time was 8.9 ns and ${\Delta}t$ of the NMOS gate drive switch was 9.9 ns.

• Korea Science and Art Forum
• /
• v.20
• /
• pp.421-428
• /
• 2015

Electronic/hybrid car and electroplating rectifier should have switching devices such as SCR, MOSFET, IGBT. And those switching devices should be operated by gate driver. In this paper, we propose high power gate driver that contains H-Bridge using 4 BJTs. H-Bridge and transformer generate isolate power. And gate control signal is transferred to isolated one by photo coupler and operate real switching device. We designed H-Bridge and 555-Timer by PSpice simulation and manufactured real product. Finally we succeed to operate 27V 50,000A electroplating rectifier using proposed gate driver.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2213-2216
• /
• 1997

Efficient Switching of IGBT's requires fast gate drivers with high peak currents. This Paper will review the requirements for effient, reliable gate drive of IGBT's and behaviour of an IGBT switching chacteristcs. The purpose of the present paper is to investigate the switching loss mechanisms in IGBT such as MOSFETs in order to give a support to designers of IGBT gate drive circuits in selecting the more appropriate IGBTs to be used on the basics of design repuirements.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.190-193
• /
• 2013

Power MOSFET and Power IGBT is develop in power savings, high efficiency, small size, high reliability, fast switching, low noise. Power MOSFET can be used high-speed switching transistors devices. Power MOSFET is devices the voltage-driven approach switching devices are design to handle on large power, power supplies, converters. In this paper, design the 80V MOSFET Planar Gate type, and design the Trench Gate type for realization of low on-resistance. For both structures, by comparing and analyzing the results of the simulation and characterization.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.237-239
• /
• 1994

The MOS-controlled thyristor(MCT) is a new power semi-conductor device that combines four layers thyristor structure presenting regenerative action and MOS-gate providing controlled turn-on and turn-off. The MCT has very fast switching speed owing to voltage controlled MOS-gate, and very low on-state voltage drop resulting from regenerative action of four layers thyristor structure. In addition, because of a higher dv/dt rating and di/dt rating, gate drive circuit and snubber circuit can be simpler comparing to other power switching devices. So recently much interest and endeavor is being applied to develop the performance and ratings of the MCT. This paper describes the switching characteristic of the MCT for its practical applications and presents a model for PSPICE circuit simulation. The model for PSPICE circuit simulation is compared to the experimental result using MCTV75P60F1 made by Harris co..

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.746-748
• /
• 1993

To overcome the problem of the diode reverse recovery in high switching frequency inverter, a new gate drive scheme is proposed for IGBT in this paper. Using this circuit, the reverse recovery current can be controlled and faster switching time can be achieved for hard switching inverter. The over-current protection method, which is suitable for the proposed gate driver, is also presented. The operation of the proposed circuit is investigated and its usefulness is verified through the experimental results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.32-39
• /
• 2010

Conventional cell characterization does not consider Multiple Input Switching(MIS). Since the impact of MIS on gate delay variation is large, it is not possible to predict the accurate gate delay with the conventional cell characterization. We observed the maximum 46% difference in gate delay due tn MIS. In this paper, we propose a gate delay model considering the delay variation caused by the temporal proximity of MIS. The proposed model calculates the delay variation using the Radial Basis Function. The experimental results show that the proposed method can more accurately predict the gate delay when MIS occurs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.822-824
• /
• 2007

This paper investigated a gate driver circuit with amorphous silicon for mobile TFT-LCD. In the conventional circuit, the fluctuation of the off-state voltage causes the fluctuation of gate line voltages in the panel and then image quality becomes worse. Newly designed gate driver circuit with dynamic switching inverter and carry out signal reduce the fluctuation of the off-state voltage because dynamic switching inverter is holding the off-state voltage and the delay of carry signal is reduced. The simulation results show that the proposed a-Si:H gate driver has low noise and high stability compared with the conventional one.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.4
• /
• pp.253-260
• /
• 2012

IGBT (insulated gate bipolar transistor) have received wide attention because of their high current conduction and good switching characteristics. To reduce the power loss of IGBT, the on state voltage drop should be lowered and the switching time should be shorted. However, there is Trade-off between the breakdown voltage and the on state voltage drop. To achieving good electrical characteristics, field stop IGBT (FS IGBT) is proposed. In this paper, 1,200 V planar gate non punch-through IGBT (planar gate NPT IGBT), planar gate FS IGBT and trench gate FS IGBT is designed and optimized. The simulation results are compared with each three structures. In results, we optain optimal design parameters and confirm excellence of trench gate FS IGBT. Experimental result by using medici, shows 40% improvement of on state voltage drop.