• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.11
• /
• pp.35-42
• /
• 2004

A CMOS folding ADC with transistor differential pair folding circuit for low power consumption and high speed operation is presented in this paper. This paper explains the theory of transistor differential pair folding technique and many advantages compared with conventional folding and interpolation circuits. A ADC based on transistor differential pair folding circuit uses 16 fine comparators and 32 interpolation resistors. So it is possible to achieve low power consumption, high speed operation and small chip size. Design technology is based on fully standard 0.25${\mu}{\textrm}{m}$ double poly 2 metal n-well CMOS process. A power consumption is 45mW at 2.5V applied voltage and 250MHz sampling frequency. The INL and DNL are within $\pm$0.15LSB and $\pm$0.15LSB respectively. The SNDR is approximately 50dB at 10MHz input frequency.

• The Journal of the Korea Contents Association
• /
• v.6 no.3
• /
• pp.38-45
• /
• 2006

A dual-level low voltage differential signalling (DLVDS) circuit is proposed aiming at reducing transmission lines for a LCD driver IC. We apply two data to the proposed DLVDS circuit as inputs. Then, the transmitter converts two inputs to two kinds of fully differential signals. In this circuit, two transmission lines are sufficient to transfer two inputs while keeping the LVDS feature. However, the circuit has a common mode bias fluctuation due to difference of the input bias and the reference bias. We compensate the common mode bias fluctuation using a feedback circuit of the current source bias. The receiver recovers the original input data through a level decoding circuit. We fabricated the proposed circuit using $0.25{\mu}m$ CMOS technology. The simulation results of proposed circuit shows 1-Gbps/2-line data rate and 35mW power consumption at 2.5V supply voltage, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.59-67
• /
• 2016

A novel instrumentation amplifier (IA) using fully-differential linear operational transconductance amplifier (FLOTA) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of a FLOTA, two resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into FLOTA converts into two same difference currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the FLOTA and realized the IA used commercial op-amp LF356. Simulation results show that the FLOTA has linearity error of 0.1% and offset current of 2.1uA at input dynamic range ${\pm}3.0V$. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the 60dB was 10MHz. The proposed IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 105mW at supply voltage of ${\pm}5V$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.836-845
• /
• 2001

A Novel fully-differential bipolar current subtracter(FCS) and its application to current controlled current amplifier(CCCA) for high-accuracy current-mode signal processing were designed. To obtain full-differential current output, the FCS was symmetrically composed of two current follower with low current-input impedance. The CCCA to control output current by the bias current was consisted of the subtracter and a current gain amplifier(CGA) with single-ended current output.. The simulation result shows that the FCS has current-input impedance of 5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100 $\mu$A to 20 mA. The power dissipation of the FCS and CCCA are 1.8 mW and 3 mW, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.8 s.338
• /
• pp.1-6
• /
• 2005

A dual-level low voltage differential signalling (DLVDS) circuit is proposed aiming at reducing transmission lines for LCD driver IC. In the proposed circuit, we apply a couple of primitive data to DLVDS circuit as inputs. The transmitter converts two inputs to two kinds of fully differential level signals. In this circuit, two transmission lines are sufficient to transfer two primitive inputs while keeping the LVDS feature. The receiver recovers The original input data through a level decoding circuit. We fabricated the proposed circuit using $0.25\mu m$ CMOS technology. The resultant circuit shows 1-Gbps/2-line data rate and 35-mW power consumption at 2.5V supply voltage, respectively.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.3
• /
• pp.183-193
• /
• 2007

Analytic solutions are derived for wave scattering by a semi-infinite breakwater or a breakwater gap with partially reflective front and fully reflective back. The water depth is constant and a regular wave train is normally incident to the breakwater. Wave scattering is studied based on the linear potential wave theory. The governing equation is transformed into ordinary differential equation by using the method of variation of parameters and coordinate transformation. Comparison with finite element numerical solution shows that the analytic solution obtained in this paper gives quite good results. Using the analytic solution, the tranquility of harbor entrance is investigated by changing the reflection coefficient at the breakwater.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.145-154
• /
• 1997

Based on a new search strategy using circuit simulation and simulated annealing with local search, a technique for design automation of high-performance operational amplifiers is proposed. For arbitrary circuit topology and performance specifications, through discrete optimization of a cost function with discrete design variables the design of operational amplifiers is performed. A special-purpose circuit simulator and some heuristics are used to reduce the design time. Through the design of a low-power high-speed fully differential CMOS operational amplifier usable in smart sensors and 10-b 25-MS/s pipelined A/D converters, it has been demonstrated that a design tool developed using the proposed technique can be used for designing high-performance operational amplifiers with less design knowledge and less design effort.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.145-148
• /
• 2011

The thermal behavior of lithiated Si anodes has been investigated using differential scanning calorimetry (DSC). In particular, the effect of Si particle size on the thermal stability of a fully lithiated Si electrode was investigated. For DSC measurements, a lithiated Si anode was heated in a hermetically sealed high-pressure pan with a polyvinylidene fluoride (PVDF) binder and a 1 M $LiPF_6$ solution in an ethylene carbonate (EC)-diethyl carbonate (DEC) mixture. The thermal evolution around $140^{\circ}C$ increases with lithiation and with decreasing particle size; this phenomenon is attributed to the thermal decomposition of the solid electrolyte interface (SEI) film. Exothermic peaks, following a broad peak at around $140^{\circ}C$, shift to a lower temperature with a decrease in particle size, indicating that the thermal stability of the lithiated Si electrode strongly depends on the Si particle size.

• Current Optics and Photonics
• /
• v.2 no.3
• /
• pp.226-232
• /
• 2018

We propose a triangular-multicore hollow optical fiber (TMC-HOF) design for uncoupled mode-division and space-division multiplexing. The TMC-HOF has three triangular cores, and each core has three modes: $LP_{01}$ and two split $LP_{11}$ modes. The asymmetric structure of the triangular core can split the $LP_{11}$ modes. Using the proposed structures, nine independent modes can propagate in a fiber. We use a fully vectorial finite-element method to estimate effective index, chromatic dispersion, differential group delay (DGD), and confinement loss by controlling the parameters of the TMC-HOF structure. We confirm that the proposed TMC-HOF shows flattened chromatic dispersion, low DGD, low confinement loss, low core-to-core crosstalk, and low crosstalk between adjacent modes. The proposed TMC-HOF can provide a common platform for MDM and SDM applications.