• 한국의류산업학회지
• /
• 제13권2호
• /
• pp.269-278
• /
• 2011

This study aims at setting up productive capacity which can be usefully utilized for work management of apparel manufacturers. So as to achieve this goal, an apparel manufacturing company which has been operated by miniline system in Seoul was selected. Standard time and man-hour were calculated to create the accurate productive capacity by observing and measuring a work flow included cutting, sewing and finishing processes. And the result is as following. The standard time for each process was presented as cutting process 47004.5s, sewing process 671050.5s and finishing process 22426.3s. And 15284.4ms was computed as total procession man-hour per day of the manufacturer which is organized of 16 people. Also, the procession man-hour for each process was revealed as cutting process 396.7ms(2.6%), sewing process 14509.3ms(94.9%) and finishing process 378.5ms(2.5%). +Surplus was found in the productivity for each process included the cutting process(outshell, lining and seam process), the sewing process(preparation and arrangement process) and the finishing process. But, additional man-hour 52436.18ms was required because the productive capacity was calculated as -surplus(-13.9%) in the sewing process(part and assembly process). Therefore, a work schedule was planned based on the previous result. However, loading can be ideal when a capacity and a load become '0'. The object company should find the way to reduce allowance(26.25%) of the sewing process through reconstruction of consciousness and improvement in functions with analyzing works of operators. Also, they need to consider an additional supplement of the personnel.

• 한국주거학회논문집
• /
• 제16권4호
• /
• pp.109-120
• /
• 2005

The purpose of this study is to find out the Consumers' value about Environmentally-Friendly Interior Finishing Material and to provide essential data for the development of realistic environmentally-friendly material also in compliance with the requirement of consumer. The questionnaire inquiry used of Analytic Hierarchy Process was carried out for both designers and common housewives to characterize the main demanding stratums for interior finishing goods in October, 2004. The results were summarized as follows; The interior finishing materials regarded as important in residential space were by the order of Wood Floor for Ondol, Wall Paper, Emulsion Paint; Environmentally-Friendly Wall Paper appeared its value of 1.56 times than Ordinary Wall Paper, in the same case of Emulsion Paint is at 1.63 times, Wood Floor at 2.12 times, respectively. Besides, as the result of correlation and regression analysis, they preferred to environmentally-friendly property by the nearer women, the nearer larger incomes, the nearer highly educated, and the nearer non-experts (housewives).

• 한국염색가공학회지
• /
• 제34권1호
• /
• pp.27-37
• /
• 2022

In this study, a study and interpretation of the spinning process in copolymerized aramid spinning was conducted. In order to proceed with the spinning process modeling and analysis, the spinning process was modeled through the physical property modeling of the spinning solution and the structural modeling of the spinneret, and structural stability and flow of the spinneret for this spinning were analyzed. After modeling the spinning solution and the spinneret in a virtual space, the pack pressure and flow rate when the spinning solution was discharged were simulated. Macroscopically, the structural stability of the spinneret was confirmed at the standard pack pressure (100 kg·f/cm²), and microscopically, the flow rate and pressure drop data of the spinning solution according to the L/D(Length (L)/Diameter (D)) value were analyzed. Based on the research and development of virtual engineering modeling and analysis, we present the possibility of changing the shape and mechanical properties of copolymer aramid fibers according to the spinning process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1507-1508
• /
• 2011

• 청정기술
• /
• 제9권2호
• /
• pp.87-100
• /
• 2003

본 연구는 청정생산기술의 개념을 염색가공분야에 도입시키기 위한 방법론을 제시한 것이다. 먼저 각 분야별 전문가로 이루어진 진단지도팀을 구성하여 대상업체에서 진행중인 제조공정 진행상태를 파악하고 사용하는 원부자재의 성능 및 환경적 분석과 폐수의 환경적 분석을 실시하였다. 원부자재(조제 및 염료)의 환경성은 TOC, CODMn, CODCr, $BOD_5$의 항목으로 평가하였고, 발생되는 폐수는 TOC, CODMn, CODCr, $BOD_5$, TDS, pH의 항목으로 평가하였다. 또 물질수지 분석과 LCA 평가 후 다음 단계로 공정, 에너지, 원부자재, 생산관리, 일반관리에서의 문제점을 도출한 후 그 중에서 개선 대상을 선정하고 마지막 단계에서 각 부분에 대해 지도하여 개선토록 한 후 최종 개선 효과를 분석하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.207-208
• /
• 2023

The procedure of predicting the construction cost and selecting the best alternative is performed based on comparative review of each building case. In the case of office building, it is required continuously until design is complete, since the owner requirements are various and likely to change during the design process compared to a standardized apartment. However, since the comparison work for each alternative in practice uses only the unit construction cost, there is no correlation between the alternative and the final result, and it is difficult to quantitatively determine the effect of the determined design factor on the total construction cost. It is needed that a means to support the generation of design alternatives using similar building cases during the design phase. This paper proposes a BIM-based data replacing process to support creating and comparison of design alternatives of internal finishing for office building. When design alternatives are created through the proposed process, it is possible to compare several similar cases with current project under equivalent design circumstance. Because only some finishing properties are replaced while maintaining the shape information such as the length, height, and base constraint of the object to be replaced.

• 한국염색가공학회지
• /
• 제22권4호
• /
• pp.300-305
• /
• 2010

Poly(ethylene terephthalate)(PET) tire cord has relatively lower adhesion properties caused by limited reacting sites. In order to improve the adhesion force between PET tire cord and rubber, an additional process to activate surface of PET has been employed. Atmospheric plasma was used to substitute the chemical finishing process of PET tire cord as a green dipping process. Contact angle was measured to confirm surface change of PET after plasma treatment. The treated PET tire cords with/without resorcinol-formaldehyde-latex(RFL) and unvulcanized rubber were vulcanized in a testing mold at $160^{\circ}C$. After atmospheric plasma treatment of PET tire cord, adhesion force was somewhat increased under some conditions.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.14-20
• /
• 1998

Automatic finishing process requires the development of high efficient and precision abrasive machining method for dies and molds. This study describes the evaluation of the finishing characteristics, such as surfrace roughness, topography and material removal depth of the electrolytic mixed abrasive machining methods. Experimental setup is composed of 3 axis machining center, a newly developed finishing attachment with constant pressure, electrode and electrolytic bath. Finally, we achieved a successful result that surface roughness is $0.01\mu$m Ra and material removal depth is $120\mu$m using electrolytic(0.8A. 30V) mixed abrasive (#400 CBN, #320 SiC) machining method.

• 한국생산제조학회지
• /
• 제4권3호
• /
• pp.31-38
• /
• 1995

Magnetic-electrolytic-abrasive polishing(MEAP) system was newly developed and the finishing characteristics of Cr-coated roller was analyzed. The paper describes the operational principle of MEAP system and magnetic field effect on the MEAP process by experimental results. The finishing characteristics and optimal finishing condition for Cr-coated roller was experimented and analyzed.

• 한국정밀공학회지
• /
• 제17권2호
• /
• pp.89-96
• /
• 2000

This paper describes the characteristic of die finishing to obtain smooth surface using electro-chemical grinding after cutting process. Electro-chemical grinding is possible under lower load and tool wear comparing with those in the mechanical grinding. Conventionally, if the metal bonding material of the grinding wheel is directly t contacted with workpiece, the current is circulated without electrolytic phenomena. Sometimes, electrical discharge is occurred between tool and workpiece. To cope with this problem, the metal-resin bonded pellet was used in this study. This pellet is composed of optimal volume of metal and resin powders and its characteristics are changable with the each volume of powders. Finally, high efficient die finishing is realized using metal resin bonded pellet in electro-chemical grinding.