• 마이크로전자및패키징학회지
• /
• 제14권3호
• /
• pp.65-71
• /
• 2007

칩 스택 패키지에 적용을 위해 폭 $75{\sim}10\;{\mu}m$, 길이 3mm의 트랜치 비아에 대해 도금전류밀도 및 rotating disc electrode(RDE)의 회전속도에 따른 Cu filling 특성을 분석하였다. RDE 속도가 증가함에 따라 트랜치 비아의 Cu filling 특성이 향상되었다. 트랜치 비아의 반폭 길이, 즉 트랜치 비아 폭의 1/2 길이와 이 트랜치 비아에 대해 95% 이상의 Cu filling 비를 얻기 위한 RDE 최소속도 사이에는 Nernst 관계식이 성립하여, 95%이상의 Cu filling비를 얻을 수 있는 최소 트랜치 비아의 반폭 길이는 RDE 속도의 제곱근의 역수에 직선적으로 비례하였다.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.26-30
• /
• 2005

Stamper surface temperature is very critical in replicating the high density optical disc substrates using injection molding as the pit or land/groove patterns on the optical disc substrate have decreased due to the rapid increase of areal density. During the filling stage, the polymer melt in the vicinity of the stamper surfaces rapidly solidifies and the solidified layer generated during polymer filling greatly deteriorates transcribability and fluidity of polymer melt. To improve transcribability and fluidity of polymer melt, stamper surface temperature should be controlled such that the growth of the solidified layer is delayed during the filling stage. In this study, the effect of heating on replication process was simulated numerically. Then, an injection mold equipped with instant active heating system was designed and constructed to raise the stamper surface temperature over the glass transition temperature during filling stage of the injection molding. Also, the closed loop controller using the Kalman filter and the linear quadratic Gaussian regulator was designed. As a result, the stamper surface temperature was controlled according to the desired reference stamper surface temperature.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.100-104
• /
• 2006

Stamper surface temperature is very critical in replicating the high density optical disc substrates using injection molding as the pit or land/groove patterns on the optical disc substrate have decreased due to the rapid increase of areal density. During the filling stage, the polymer melt in the vicinity of the stamper surfaces rapidly solidifies and the solidified layer generated during polymer filling greatly deteriorates transcribability and fluidity of polymer melt. To improve transcribability and fluidity of polymer melt, stamper surface temperature should be controlled such that the growth of the solidified layer is delayed during the filling stage. In this study, the effect of heating on replication process was simulated numerically. Then, an injection mold equipped with instant active heating system was designed and constructed to raise the stamper surface temperature over the glass transition temperature during filling stage of the injection molding. Also, the closed loop controller using the Kalman filter and the linear quadratic Gaussian regulator was designed. As a result. the stamper surface temperature was controlled according to the desired reference stamper surface temperature.

• 대한수학회보
• /
• 제47권6호
• /
• pp.1213-1224
• /
• 2010

Using Ahlfors' covering surface method, some properties on the strong Borel direction of algebroid function of finite order are obtained. The main object of this paper is to prove existence theorem of a strong Borel direction and the existence of filling discs in such direction which briefly extends some results of meromorphic function.

• Restorative Dentistry and Endodontics
• /
• 제13권1호
• /
• pp.53-67
• /
• 1988

An investigation was carried out to compare the pulp responses against a few type of composite and streptococcus mutans contamination under the zinc oxide eugenol cement, and also confirmed pulpal responses of various composites with or without base. Seventy eight teeth from 6 dogs were employed and divided into 6 groups. Class V cavities were prepared on each tooth routinely with low speed dental engine. Paper disc about 0.3mm thick was immersed in the BHI broth in which streptococcus mutans had been enriched and the disc was inserted on the cavity floor prior to filling. Scotch bond puls Silux as Bis-GMA system composite resin and Helimolar as urethane system composite resin were adopted. Control group: Zinc-Oxide Eugenol cement filling Experimental groups: Group 1. Scotch bond + Silux filling with Dycal base Group 2. Heliomolar filling with Dycal base Group 3. Scotch bond + Silux filling without base Group 4. Heliomolar filling without base Group 5. Streptococcus mutans application. All cavities were sealed with thick ZOE cement to avoid marginal leakage. Postoperative intervals of 1, 2, 3, 4, 5 and 6 weeks teeth were carefully extracted, processed and stained with Hematoxylin and Eosin. The results were as follows: 1. S. mutans application group and composites without any base showed more severe pupal response than control group and dyca based groups. 2. The experimental group of S. mutans application showed severe response in the early stage compared to the two groups of composite resin without base, but no significant difference was found following periods. 3. The difference of pulpal response is not significant between Bis-GMA system and urethane system. 4. Streptococcus mutans application group and composites without base groups showed the evidence of histologic recovery at the six week cases and the large amount of reparative dentin was the prominent feature. 5. Pulp responses against every material were inclined to normal according to the time elapsed.

• Restorative Dentistry and Endodontics
• /
• 제33권2호
• /
• pp.115-124
• /
• 2008

본 연구의 목적은 수 종의 레진계 임시수복재의 중합수축 및 수화팽창을 측정하고 레진계 임시수복재와 와동면 사이의 미세누출을 평가하고자 하였다. 본 실험의 재료는 5종의 광중합형 레진계 임시충전재 Fermit, Quicks, Provifil, Spacer, Clip와 대조군으로 석고계 충전재 Caviton을 사용하였다. 'Bonded disc method'를 이용하여 중합수축을 측정하였고, 미리 중합된 디스크 형태의 시편을 생리식염수에 담그고 LVDT로 7 일 동안 수화팽창을 기록하였다. 발거된 120개의 상, 하악 대구치에 1 급 와동을 형성한 후 각각 20개씩 6개의 군으로 나누어 각 재료를 충전한 후, 1000 회의 Thermocycling을 실시하고 2% methylene blue 염색 용액을 이용하여 미세누출을 평가하였다. 연구결과는 다음과 같다. 1. Fermit의 중합수축이 가장 적었고 (0.22%) Spacer (0.38%), Quicks (0.64%) Provifil (0.67%), Clip (0.67%) 의 순이었다. 2. 모든 재료는 24 시간 이내에 급격한 수화팽창을 나타냈고 7 일 후 수화팽창은 Caviton이 가장 컸다 (11.5%). 레진계 임시수복재는 0.43-1.1%가량 팽창하였다. 3. Fermit의 미세누출이 가장 많았으며 Quicks의 미세누출이 가장 적었다. Spacer와 Clip은 Caviton과 비슷한 정도의 미세누출을 보였다. 4. 중합수축 또는 수화팽창과 미세누출 사이의 직접적 인 상관관계는 관찰할 수 없었다.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1602-1611
• /
• 2021

A varying degree of eccentricity always exists in the initial configuration of a nuclear fuel rod. Its impact on traditional LWR fuel is limited as the radial gap closes relatively early during irradiation. However, the effect of misalignment is expected to be more relevant in rods with highly conductive fuels, large initial gaps and low conductivity filling gases. In this paper, we study similar characteristics in the experimental setup of two fuel disc irradiation campaigns carried out in the OECD Halden Boiling Water Reactor. Using the multi-dimensional fuel performance code OFFBEAT, we combine 2-D axisymmetric and 3-D simulations to investigate the effect of eccentricity on the fuel temperature distribution. At the same time, we illustrate how the advent of modern tools with multi-dimensional capabilities might further improve the design and interpretation of in-pile separate-effect tests and we outline the potential of such an analysis for upcoming experiments.

• 대한치과보철학회지
• /
• 제35권4호
• /
• pp.719-741
• /
• 1997

This study was undertaken to compare by Atomic Force Microscope the effects of various finishing and polishing instruments on surface roughness of filling and veneering composite resins. Seven composite resins were studied : Silux Plus (3M Dental Products, U.S.A.), Charisma (Heraeus Kulzer, Germany), Prisma THP (L.D.Caulk, Dentsply, U.S.A.), Photoclearfil (Kuraray, Japan), Cesead (Kuraray, Japan), Thermoresin LC (GC, Japan), Artglass (Heraeus Kulzer, Germany). Samples were placed and polymerized in holes (2mm thick and 8.5mm in diameter) machined in Teflon mold under glass plate, ensuring excess of material and moulded to shape with polyester matrix strip. Except control group (Polyester matrix strip), all experimental groups were finished and polishied under manufacturer's instructions. The finishing and polishing procedure were : carbide bur (E.T carbide set 4159, Komet, Germany), diamond bur (composite resin polishing bur set, GC, Japan), aluminum-oxide disc (Sof-Lex Pop-On, 3M Dental Products, U.S.A.), diamond-particle disc (Dia-Finish, Renfert Germany), white stone bur & rubber point( composite finishing kit, EDENTA, Swiss), respectively. Each specimens were evaluated for the surface roughness with Atomic Force Microscope (AutoProbe CP, Park Scientific Instruments, U.S.A.) under contact mode and constant height mode. The results as follows : 1. Except Thermoresin LC, all experimental composite resin groups showed more rougher than control group after finishing and polishing(p<0.1). 2. A surface as smooth as control group was obtained by $Al_{2}O_{3}$ disc all filling composite resin groups except Charisma and all veneering composite resin groups except Thermoresin LC(p<0.05). 3. In case of Thermoresin LC, there were no statistically significant differences before and after finishing and polishing(p>0.1). 4. Carbide bur, diamond bur showed rough surfaces in all composite resin groups, so these were inappropriate for the final polishing instruments.

• 소음진동
• /
• 제10권1호
• /
• pp.123-128
• /
• 2000

This paper describes the optimization of the hexagonal array transducer using finite element method. The transducer consists of the disc type sensors. Three dimensional beam patterns of each element and the array transducer are analysed using the finite element code ATILA. Beam patterns were analyzed for the disc type transducer. To optimize beam patterns of the array transducer, Chebyshev polynomial weight is applied to each element. In case of applying optimized weight, a 30 degree width beam pattern is presented at 10kHz. This paper also includes the effect of rubber filling material instead of using the water inside the transducer array.

• Structural Engineering and Mechanics
• /
• 제85권3호
• /
• pp.337-351
• /
• 2023

In this paper, the shear behavior of soft filling in rectangular-hollow concrete specimens was simulated using the 2D particle flow code (PFC2D). The laboratory-measured properties were used to calibrate some PFC2D micro-properties for modeling the behavior of geo-materials. The dimensions of prepared and modeled samples were 100 mm×100 mm. Some disc type narrow bands were removed from the central part of the model and different lengths of bridge areas (i.e., the distance between internal tips of two joints) with lengths of 30 mm, 50 mm, and 70 mm were produced. Then, the middle of the rectangular hollow was filled with cement material. Three filling sizes with dimensions of 5 mm×5 mm, 10 mm×5 mm, and 15 mm×5 mm were provided for different modeled samples. The parallel bond model was used to calibrate and re-produce these modeled specimens. Therefore, totally, 9 different types of samples were designed for the shear tests in PFC2D. The shear load was gradually applied to the model under a constant loading condition of 3 MPa (σc/3). The loading was continued till shear failure occur in the modeled concrete specimens. It has been shown that both tensile and shear cracks may occur in the fillings. The shear cracks mainly initiated from the crack (joint) tips and coalesced with another one. The shear displacements and shear strengths were both increased as the filling dimensions increased (for the case of a bridge area with a particular fixed length).