• 한국지구물리탐사학회:학술대회논문집
• /
• 2008.10a
• /
• pp.149-154
• /
• 2008

We analyzed the Coulomb stress transfer near a small-scale reverse fault. For the modeling we used the geometry of a Quaternary fault in Gyeongju area, Eupcheon fault. For an assumed reverse faulting slip of 10cm, the resulting values of the Coulomb stress change are relatively higher (>2 bar) near the edges (both downward and lateral) of the fault, and diminish slightly upward and downward. The equivalents are negative in the zone immediately below and above the fault, exhibiting a "T" shape of low stress zone in the vertical profile of the fault. This study demonstrates the possible ranges and directions the aftershock energy would propagates after a reverse faulting.

• Tunnel and Underground Space
• /
• v.15 no.2 s.55
• /
• pp.111-118
• /
• 2005

The area of investigation belongs to Okchon metamorphic zone and the fault fractured zone runs parallel to the tunnel direction. It causes the independent decline of tunnel face and the slackness of the tunnel surrounding base so, after all, the severe displacement has occurred within the tunnel. Accordingly, the TSP(Tunnel Seismic Prediction) survey has been performed to investigate the extent of fault fractured zone and to analize its characteristics. Also, we have analized the behavior causes by performing the tunnel face mapping and drilling investigation, and confirmed the position and scale of geological anomaly area and front fractured zone which influences tunnel excavation and supporting. Collected data analyzed ground layer condition through 3 dimensional modeling. Several variables included in the modeling were analyzed by geostastistics. The analysis of the modeling data shows that the belt of weathering by fault fractured zone is developing on the basis of the right side of tunnel and that is decreasing to the left side. The fault fractured zone was confirmed that it has strike, $N0\~5^{\circ}E$ dip NW, and it is consisted of large-scale fractured zone including several anomalies. The severe displacement in tunnel is probably caused by asymmetrical load that n generated by the crossing of discontinuity and the rock strength imbalance of tunnel's both side by fault fractured zone, and judge that need tunnel reinforcement method of grouting etc.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.89-93
• /
• 2002

We investigated the resistance distribution n 4"diameter SFCLS. $YBa_2CU_3O_7$ films coated in-situ with a gold layer were patterned into 3 mm wide 142 cm long meander lines by Photolithography. The limiters were tested with simulated fault currents. The resistance was uniform all over the film except at the edge. At lower source voltages, CFCLs did not quench simultaneously and the resistance distribution was less uniform. Compared with 2" diameter SFCLS 4" SFCLS had similar values and time dependence of resistivity at similar electric fields The resistance distribution was more uniform in 4" SFCLS. The area at the edge where the distribution was not uniform was around 3 mm wide in SFCLs of both sizes. The experimental results were quantitatively explained with a heat transfer concept.

• Tunnel and Underground Space
• /
• v.27 no.2
• /
• pp.77-88
• /
• 2017

The geology of the study area is composed mainly of conglomerate, sandstone, and shale and basalt. It is a rock that has been observed to move relatively recently through various brittle deformation and various stress fields during the recent period. To form a gentle terrain with severe crushing. The slope is located at the intersection of the Taegok Fault in the north-northeast direction and the Bukok Fault in the western north-west direction, and many faults, fault zones and fracture zones of various sizes are developed in the rock bed. In this study, the geological characteristics of the slope are investigated and the countermeasure method is suggested. It is suggested that periodical measurement and analysis should be performed by installing a measuring instrument according to each structure for safety management of the surrounding roads and grounds during construction or reinforcement by the countermeasure method for the slope of the study area.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.3
• /
• pp.441-448
• /
• 2022

In the distribution system, there are multiple power protection systems such as circuit breakers at substations, and reclosers, minimum circuit ampacities, fault interrupters on distribution lines. They are widely used to prevent partial outages, cascading power failure or blackout so that other healthy systems could maintain the integrity in case of the instant fault or permanent failure on the power lines. However, when a fault happens, it could cause a major black out due to the lack of the protection cooperation between the protection relay of the circuit breaker at a substation and a protection system on the distribution lines. To achieve the power system integrity better, it is required to develop the circuit breaker which can be operational within 1 cycle(16ms). In this study, the high speed circuit breaker which is filled up with eco-friendly gas is developed. This equipment achieved an excellent test results based on IEC 62271-111 standard. It is respected that this equipment would contribute to prevent the wide area blackout by isolating a fault area quicker and faster.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.674-677
• /
• 2005

The characteristics of geothermal resources in Korea was roughly estimated using hot springs, 580 geothermal gradients and 338 heat flow data. In the aspect of hot springs with geologic structure, location of hot springs coincide with fault zone, especially younger age of Cretaceous to Tertiary. In the aspect of geothermal gradients, Pohang area shows the highest geothermal gradient anomaly, which is covered with unconsol idated rock of low thermal conductivity preserving the residual heat from igneous activity or radioactivity elements decay. In the aspect of heat flow density, high anomaly can be found along the zone connecting Uljin-Pohang-Busan on the southeastern part of Korean peninsula at which big fault zone as Yangsan fault is well developed.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.179.3-179
• /
• 2001

This paper describes the dual system technology of PC based control system at steel plant. Because PC is developed to be used in wide area such as Office Automation, Personal, It is cheaper and more portable than the present process control system, but is less stable and less reliable. In this research, We gathered the fault example of a general process control system and steel process control system, analyzed the cause of fault and decided the target fault that took over in our proposed system. The proposed PC based system is the dual system that has a shared RAID system connected by SCSI bus between two systems. In order to assist system reliability, we proposed watchdog manager to monitor ...

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.2
• /
• pp.179-183
• /
• 2008

In case of a line-to-ground fault at transmission lines, a portion of fault current will flow into the earth through the footings of the faulted tower causing electrical potential rise nearby the faulted tower footings. In this situation, any buried pipelines or structures nearby the faulted tower can be exposed to the electrical stress by earth potential rise. Although many research works has been conducted on this phenomena, there has been no clear answer of the required separation distance between tower footings and neary buried pipeline because of its dependancy on the soil electrical charactersics of the concerned area and the faulted system. In this paper, an analytical formula to calculate the requried sepeartion distance from the faulted tower has been derived.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.12
• /
• pp.1710-1715
• /
• 2014

In this paper, we propose a novel on-chip test logic for TSV fault detection in 3-dimensional integrated circuits. The proposed logic called OTT realizes the input signal delay-based TSV test method introduced earlier. OTT only includes one F/F, two MUXs, and some additional logic for signal delay. Thus, it requires small silicon area suitable for TSV testing. Both pre-bond and post-bond TSV tests are able to use OTT for short or open fault as well as small delay fault detection.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.10
• /
• pp.1021-1028
• /
• 1990

This paper deals with the development of an expert system for the fault diagnosis in a power system. The expert system is designed to estimate the fault sections with explanation about the propagation of the faults through the identification of false operation of protective devices. The identification of black-out area is also considered to assist the restoration process. As for the inference scheme, backward chaining method is adopted and the search space is reduced for the better performance. The expert system was developed using PROLOG language. Its application to a sample power system showed satisfactory result.