• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.872-875
• /
• 2003

Carbon nitride($CN_x$) thin films were deposited on quartz substrates using reactive RF magnetron sputtering system at uarious deposition conditions and investigated dielectric characteristics. Samples for capacitance measurements were of the MIM(Metal-Insulator-Metal) type devices. Aluminum film electrodes were prepared by a vacuum thermal evaporation method before and after the deposition of carbon nitride films. Capacitances were measured by a FLUKE PM6306 RCL Meter at room temperature. Current-voltage(I-V) characteristics and resistivity were measured by a CATS CA-EDA semiconductor test and analyzer. The carbon nitride films showed ${\alpha}-C_3N_4$ and ${\beta}-C_3N_4$ etc. peaks through Raman and FTIR. Observed surface of film and side structure using SEM(Scanning Electron Microscope), and measured thickness of film by ${\alpha}-step$. We can find that the dielectric constant was the lowest value in 50% nitrogen ratio and the resistivity was the highest value in 70% nitrogen ratio.

• Journal of Electrical Engineering and Technology
• /
• 제7권6호
• /
• pp.845-851
• /
• 2012

Power system loads have a significant impact on a system. Although it is difficult to precisely describe loads in a mathematical model, accurately modeling them is important for a system analysis. The traditional load modeling method is based on the load components of a bus. Recently, the load modeling method based on measurements from a system has been introduced and developed by researchers. The two major components of a load modeling problem are determining the mathematical model for the target system and estimating the parameters of the determined model. We use the composite load model, which has both static and dynamic load characteristics. The ZIP model and the induction motor model are used for the static and dynamic load models, respectively. In this work, we propose the measurement-based parameter estimation method for the composite load model. The test system and related measurements are obtained using transient security assessment tool(TSAT) simulation program and PSS/E. The parameter estimation is then verified using these measurements. Cases are tested and verified using the sample system and its related measurements.

• Transactions on Electrical and Electronic Materials
• /
• 제17권5호
• /
• pp.293-296
• /
• 2016

Using capacitance-voltage (C-V) and conductance-voltage (G/ω-V) measurements, the electrical properties of Cu/n-InP Schottky diodes were investigated. The values of C and G/ω were found to decrease with increasing frequency. The presence of interface states might cause excess capacitance, leading to frequency dispersion. The negative capacitance was observed under a forward bias voltage, which may be due to contact injection, interface states or minority-carrier injection. The barrier heights from C-V measurements were found to depend on the frequency. In particular, the barrier height at 200 kHz was found to be 0.65 eV, which was similar to the flat band barrier height of 0.66 eV.

• Transactions on Electrical and Electronic Materials
• /
• 제9권4호
• /
• pp.151-155
• /
• 2008

Using pentacene field effect transistors (FETs) with Au source and drain electrodes, electron injection from the Au electrodes into the pentacene was investigated. The capacitance-voltage (C-V) and optical second harmonic generation (SHG) measurements were employed. Electron injection from the Au electrodes was suggested by the hysteresis behavior with the C-V characteristics and slowly decaying SHG signal under DC biasing, A mechanism of hole-injection assisted by trapped electrons is proposed. To confirm electron injection process, light-emitting behavior under the application of AC applied voltage was observed.

• 한국재료학회지
• /
• 제26권10호
• /
• pp.556-560
• /
• 2016

Using current-voltage (I-V) and capacitance-voltage (C-V) measurements, the electrical properties of Au and Cu Schottky contacts to n-Ge were comparatively investigated. Lower values of barrier height, ideality factor and series resistance were obtained for the Au contact as compared to the Cu contact. The values of capacitance showed strong dependence on the bias voltage and the frequency. The presence of an inversion layer at the interface might reduce the intercept voltage at the voltage axis, lowering the barrier height for C-V measurements, especially at lower frequencies. In addition, a higher interface state density was observed for the Au contact. The generation of sputter deposition-induced defects might occur more severely for the Au contact; these defects affected both the I-V and C-V characteristics.

• 한국전기전자재료학회논문지
• /
• 제14권3호
• /
• pp.202-206
• /
• 2001

Using THz time-domain spectroscopy (THz-TDS), the power absorption, the index of refraction, and the real conductivity of silica sand are measured from 0.1[Thz] to 0.5[Thz] frequency range. It is impossible to measure the characterization of the silica sand by simple electrical measurements using mechanical contacts, e.g., Hall effect or four-point probe measurements. However, the THz-TDS technique can measure not only electrical but also optical characterization of he sample. Also this technique can measure frequency dependent results. Especially, the real conductivity was increased according to THz frequency. This is unusual material compare with metal and semiconductor materials; the measured real conductivity are not followed by the simple Drude theory.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.367-367
• /
• 2007

Polymer/nanoparticle hybrids have been increasingly studied because of their enhanced properties for organic light emitting devices (OLEDs). In this study, we made poly(p-phenylene vinylene) (PPV) nanohybrid films by incorporation of Ag and $SiO_2$ nanoparticles into the PPV. A possible interaction between nanoparticles was investigated and especially we focused whether there is a change in the interaction between $SiO_2$ or Ag nanoparticles and matrix or not. The current characteristics of PPV nanohybrid films were analyzed by I-V and EL measurements. The optical properties were also investigated by UV-Vis spectroscopy and photoluminescence measurements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 추계학술대회 논문집
• /
• pp.129-133
• /
• 1994

$ZnO_{x}$ films were deposited by conventional thermal evaporation method. Zinc acetate was used as precursor. XRD and SEM results shows films as mixed stats of ZnO and zinc acetate. And EDX measurements reseal composition of films as $ZnO_{x}$.

• 전기의세계
• /
• 제29권2호
• /
• pp.111-117
• /
• 1980

Contacts formed by vacuum evaporation of As-Te-Si-Ge chalcogenide glass onto Al metal (99.9999%) are studied by measuring paralle capacitance C(V), Cp(w), resistance R(V), Rp(w), and I-V characteristics. The fact that contact metal alloying produced high-resistance region is confirmed from the measurements of parallel capacitance and resistance. From the I-V characteristics in the pre-switcing region, it is found that electronic conduction and sitching occurs in the vicinity of metal-amorphous semiconductor interface. From the experimental obsevations, it is concuded that the current flow in the thin film is space-charge limited current (SCLC) due to the tunneling of electrons through the energy barriers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.167-170
• /
• 1998

The electrical characteristics of Stearic acid LB films were investigated to develop the gas sensor using Langmuir-Blodgett(LB) films. The deposition status of LB films were verified by the measurements of UV absorbance and I-V characteristics. The conductivity of Stearic acid LB films at room temperature was $10^{-8}[S/cm]$, which is typical of semiconductor. The conductivity was found to increase as the temperature was increased. The acitivation energy was about 1[eV].