• 한국건축시공학회지
• /
• 제2권3호
• /
• pp.163-170
• /
• 2002

Recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, for use of polishing tile in the dry wall system which used to lightweight wall, the examination of adhesive stability of polishing tile is needed. In this study, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and Polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II). As the result of study are the follows; (1) Polishing tile(600$\times$400mm) construction on waterproofing layer : Both laboratory estimation and spot examination sieve were happened that fall of tile because their hardening speed is late. (2) To using powder style adhesives in the dry wail with waterproofing layer : Adhesive strength of tile is Influenced by interface bond area and base side condition. (3) Shock and heat stresses : obvious decline of adhesive strength is not happened

• Journal of the Korean Wood Science and Technology
• /
• 제35권5호
• /
• pp.7-15
• /
• 2007

To evaluate the durability of finger-jointed woods according to change of humidity conditions, four types of finger-jointed woods glued with different kinds of adhesives and finger pitches were made with Sitka spruce, and the effect of humidity conditions on creep performances was investigated. The shape of creep curves differed among humidity conditions, and the inclination of creep curves was greatest in 85%RH, and lowest in 65%RH. Their creep curves showed a linear behavior beyond approximately one hour, regardless of humidity conditions. The A values of the creep curves fitted to power law increased with increasing relative humidity, whereas the A' values were in order of 30 > 85 > 65%RH unlike the A values. The initial deformation increased with increasing relative humidity, whereas the creep deformation unlike the initial deformation was in order of 85 > 30 > 65%RH, and it was found that the creep deformation of finger-jointed woods indicated the smaller amount in air-dry moisture content rather than in a low moisture content less than 30%RH. Finger-jointed woods with 6.8 mm (L) pitch had the greater creep amount than in those with 4.4 mm (S) pitch in all humidity conditions. The difference of creep amount between both adhesives in all humidity conditions was small. Relative creep at 240 hr was greatest as 62.2~71.9% in 85%RH, and the values indicated 2.1~2.6 times that of 30%RH and 3.0~3.6 times that of 65%RH and were equal or slightly greater than that of solid spruce.

• Journal of the Korean Wood Science and Technology
• /
• 제47권3호
• /
• pp.253-264
• /
• 2019

This study characterized the chemical compounds in tannin from mangium (Acacia mangium) bark extract and determined the physical-mechanical properties of glued laminated timber (glulam) made from sengon (Falcataria moluccana), jabon (Anthocephalus cadamba), and mangium wood. The adhesives used to prepare the glulam were based on mangium tannin and phenol resorcinol formaldehyde resin. Five-layer glulam beams measuring $5cm{\times}6cm{\times}120cm$ in thickness, width, and length, respectively, were made with a glue spread of $280g/m^2$ for each glue line, cold pressing at $10.5kgf/cm^2$ for 4 h and clamping for 20 h. Condensed mangium tannin consisted of 49.08% phenolic compounds with an average molecular weight of 4745. The degree of crystallinity was 14.8%. The Stiasny number was 47.22%. The density and the moisture content of the glulams differed from those of the corresponding solid woods with mangium having the lowest moisture content (9.58%) and the highest density ($0.66g/cm^3$). The modulus of rupture for all glulam beams met the JAS 234-2003 standard but the modulus of elasticity and the shear strength values did not. Glulam beams made with tannin had high delamination under dry and wet conditions, but glulam made from sengon and jabon wood met the standard's requirements. All glulam beams had low formaldehyde emissions and were classified as $F^{****}$ for formaldehyde emissions according to the JAS 234 (2003) standard.

• Restorative Dentistry and Endodontics
• /
• 제29권2호
• /
• pp.153-161
• /
• 2004

This study investigated that the effect of rewetting agent on dentinal microtensile bond strength(${\mu}TBS$). Human molars were sectioned to expose the superficial dentin surfaces. Samples were divided into two groups according to type of adhesives-Single Bond (S) and One-Step (0)], and again subdivided into five groups by different dentin surface treatment-dry for 15s (D), blot dry (BD) or dry for 15s, and rewet with different rewetting agents [distilled water (DW), Gluma Desensitizer (GD) and Aqua-Prep (AP)] for 30s. After application of adhesive, composite resin was built up on the bonding surface. Each tooth was sectioned to obtain stick with $1\textrm{mm}^2$ cross sectional area and the ${\mu}TBS$ was determined by EZ test. In the S group, the mean ${\mu}TBS$ of GD, AP, and BD group was significantly higher than that of DW and D group (p < 0.05), In the O group, the mean, ${\mu}TBS$ of AP, GD, BD and DW group was significantly higher than that of D group (p < 0.05). The data suggested that Gluma Desensitizer and Aqua-Prep could be successfully used as rewetting agents, and Distilled water could be acceptable in aceton based adhesive system only.

• The Journal of Advanced Prosthodontics
• /
• 제1권2호
• /
• pp.63-67
• /
• 2009

STATEMENT OF PROBLEM. Use of custom tray and tray adhesive is clinically recommended for elastomeric impression material. However there is not clear mention of drying time of tray adhesive in achieving appropriate bonding strength of tray material and impression material. PURPOSE. This study is to investigate an appropriate drying time of tray adhesives by evaluating tensile bonding strength between two types of polyvinylsiloxane impression materials and resin tray, according to various drying time intervals of tray adhesives, and with different manufacturing company combination of impression material and tray adhesive. MATERIAL AND METHODS. Adhesives used in this study were Silfix (Dentsply Caulk, Milford, Del, USA) and VPS Tray Adhesive (3M ESPE, Seefeld, Germany) and impression materials were Aquasil Ultra (monophase regular set, Dentsply Caulk, Milford, Del, USA) and Imprint II Garant (regular body, 3M ESPE, Seefeld, Germany). They were used combinations from the same manufacture and exchanged combinations of the two. The drying time was designed to air dry, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 25 minutes. Total 240 of test specimens were prepared by auto-polymerizing tray material(Instant Tray Mix, Lang, Wheeling, Il, USA) with 10 specimens in each group. The specimens were placed in the Universal Testing machine (Instron, model 3366, Instron Corp, University avenue, Nowood, MA, USA) to perform the tensile test (cross head speed 5 mm/min). The statistically efficient drying time was evaluated through ANOVA and Scheffe test. All the tests were performed at 95% confidence level. RESULTS. The results revealed that at least 10 minutes is needed for Silfix-Aquasil, and 15 minutes for VPS Tray Adhesive-Imprint II, to attain an appropriate tensile bonding strength. VPS Tray Adhesive-Imprint II had a superior tensile bonding strength when compared to Silfix-Aquasil over 15 minutes. Silfix-Aquasil had a superior bonding strength to VPS Tray Adhesive-Aquasil, and VPS Tray Adhesive-Imprint II had a superior tensile bonding strength to Silfix-Imprint II at all drying periods. CONCLUSION. Significant increase in tensile bonding strength with Silfix-Aquasil and VPS Tray adhesive-Imprint II combination until 10 and 15 minutes respectively. Tray adhesive-impression material combination from the same company presented higher tensile bonding strength at all drying time intervals than when using tray adhesive-impression material of different manufactures.

• Journal of the Korean Wood Science and Technology
• /
• 제43권4호
• /
• pp.528-537
• /
• 2015

폐기물의 재활용을 도모하기 위해 음식점이나 정육점에서 폐기되는 뼈(골분)를 합판용 접착제의 충전제로서 이용 가능성을 검토하였다. 현재 업계에서 합판의 제조에 사용되고 있는 3종의 접착제(UMF, UF 및 PF수지)에 대해 3종의 골분(소골분, 돼지골분 및 조개골분)을 첨가하여 제조한 라티에타파인 합판의 접착성능을 기존의 소맥분과 비교하였다. 3수지에서 모두 소맥분을 전부 소골분, 돼지골분 및 조개골분으로 각각 대체한 합판의 접착성능은 상태나 습윤 강도 및 목파율 모두 소맥분 첨가 합판보다 낮았다. 따라서 소맥분을 전혀 첨가하지 않고 골분으로 모두 대체하는 것은 곤란하였다. 그러나, 소맥분의 절반을 소골분과 돼지골분으로 각각 대체하여 제조한 합판의 성능은 소맥분을 사용한 합판과 거의 동등하거나 오히려 우수한 내수성능을 발휘하여 소맥분과 병용해서 사용하면 충분히 이용이 가능할 것으로 생각된다. 소맥분과 병용한 경우, 3종의 골분 중에는 조개골분을 첨가하여 제조한 합판 보다는 소골분과 돼지골분을 첨가한 합판의 성능이 우수하였으며, 소골분과 돼지골분 간에는 큰 차이가 없었다.

• Journal of the Korean Wood Science and Technology
• /
• 제37권1호
• /
• pp.56-64
• /
• 2009

본 연구의 목적은 콩기름을 오존 산화 처리하여 기능기를 도입하고 이를 바탕으로 친환경 목재 접착제를 개발하는 것이다. 시판용 콩기름을 시간당 약 7.13 g의 오존을 발생시켜 15분, 30분, 60분, 120분간 오존산화 처리한 후 FT-IR, $^1H$-NMR, MALDI-TOF MS, GC/MS 측정하여 구조변화를 분석하였다. 기기분석 결과 오존산화처리에 의하여 콩기름의 불포화 이중결합이 개열되어 카르복실기 또는 알데하이드기가 생성됨을 확인하였다. 오존산화콩기름 변성 pMDI 접착제의 접착력은 오존처리 정도와 pMDI의 혼합비율에 따라 달라지며, KS F 3101 보통합판기준 내수 접착강도를 안정적으로 만족 시키는 조건은 오존산화 처리시간 30분~60분, pMDI와 1:1로 혼합한 경우이며, 준내수 접착강도를 만족시키는 범위는 오존산화 처리시간 30분~60분, pMDI의 혼합비 0.5이상, 상태접착강도를 만족시키는 범위는 오존산화 처리시간 15분~60분, pMDI의 혼합비 0.25 이상임을 알 수 있었다. 위의 실험결과를 종합하여 볼 때, 오존산화 처리한 식용유는 오존처리시간 및 pMDI의 혼합비율을 조절하면 상태접착력 뿐만 아니라 내수접착력이 요구되는 목질복합재료 제조용 접착제 제조가 가능함을 확인할 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제39권6호
• /
• pp.498-504
• /
• 2011

The purpose of this study was to investigate and develop an eco-frendly wood adhesive based on vegetable oil (especially soybean oil), the renewable and sustainable natural resources, using ozonification technology for the chemical structure modification. The waste soybean oil (WSBO) was reacted with $O_3$ at the rate of $450m{\ell}$(acetone) : $50m{\ell}$ (WSBO) for different times, 1, 2, 3 hrs. The investigation of the modified chemical strecture of the ozonied WSBOs were conducted using FT-IR. As ozonification time increased, the peak of the unsaturated double bonds was disappeared especially ozonized-3hrs and aldehyde or carboxyl peak appeared because ozonification broke the oil into small molecules. The plywood were made at $150^{\circ}C$ with 4 minutes hot-press time using the different ozonized 3 hrs WSBO/pMDI adhesives and were tested for the dry, wet, cyclic boil test according to the Korea Industrial Standard F3101 Ordinary plywood. The bond strengths gradually increased until 1 : 0.5~1 : 3, but it decreased 1 : 4, as the contents of pMDI increased. The results of the dry, wet and cyclic bond strengths the equivalent ratio was formed approximately between 1 : 2~1 : 3. And the 1 : 1~1 : 4 strengths met constantly the standard requirement of 7.0kgf/$cm^2$ (KS F3101). From the comprehensive view on the results of above experiment, it could be confirmed that ozonized WSBO/pMDI has characteristics of effective reactivity and wet stability showed as an excellent candidate of wood adhesive applications.

• 구강회복응용과학지
• /
• 제16권2호
• /
• pp.123-132
• /
• 2000

The field of maxillofacial prosthetics is concerned with the prosthetic reconstruction of missing head and neck tissue. Currently, facial prostheses are usually applied in cases of defects caused by the surgical removal of tumors or congenital defects. While silicone has been most widely used for the reconstruction of missing maxillofacial defects, it does not have ideal physical properties. Therefore, bonding a thin polyurethane sheet to silicone prostheses was recommended. In this case skin adhesives were used for the retention of maxillofacial prostheses. But retention of devices has always been problematic. The contributions of implants can be made to solve these problems. Implants have reduced the need for adhesive use, simplifying cleaning procedures and thus extending the life of the prostheses. For implant-retained prostheses, retentive matrix is necessary to hold attachments and/or magnets. The retentive matrix is usually fabricated with autopolymerizing acrylic resin or visible light- polymerized resin. The purpose of this study was to compare the adhesion-in-peel force of silicone adhesive to autopolymerizing acrylic resin and polyurethane sheet with two different surface textures : pumice polish only or retention groove, and three surface primers : Dow corning 1205 primer or Dow corning S-2260 primer or FactorII A-304 primer, and two polymerization methods : room temperature or dry heat oven. The t-peel bond strength of specimens was determined as described in ASTM Standard D1876-72. The results were statistically analyzed using the ANOVA test, multiple range test and t-test The results were as follows. 1. The t-peel bond strength of A-304 primer was the highest and statistically higher than that of S-2260(p<0.05). 2. The t-peel bond strength of specimens with retention groove was statistically higher than that of specimens polished with pumice(p<0.05). 3. The t-peel bond strength of specimens polymerized in dry heat oven was statistically higher than that of specimens in room temperature(p<0.01).

• Restorative Dentistry and Endodontics
• /
• 제35권3호
• /
• pp.211-221
• /
• 2010

본 연구는 상아질의 비교원성 단백질을 chondroitinase ABC (C-ABC)를 이용하여 제거함으로써 비교원성 단백질의 제거가 상아질 접착제의 미세인장결합강도와 교원질망의 형태에 미치는 영향을 상아질의 다양한 습윤상태에 따라 평가하고자 시행하였다. 비교원성 단백질의 상아질접착제의 미세인장강도에 대한 영향을 평가하기 위해 제 3대구치의 상아질을 노출시키고, 두 군으로 나누고 한 군은 C-ABC, 다른 군은 증류수를 $37^{\circ}C$에서 48시간 동안 적용한 후, 상아질의 습윤상태(wet, dry 및 re-wet)와 상아질 접착제(Single Bond 2, One Step Plus)를 다르게 이용하여 복합레진을 수복하였다. 24시간 후 가로 1 mm, 세로 1mm의 시편을 제작하고 미세인장강도를 측정하였다. 상아질 교원질의 형태변화를 관찰하기 위하여 상아질 시편에 산부식을 시행하고 C-ABC 적용 후, 시편을 제작하였고 미세인장강도 측정후 파괴된 접착면의 파괴양상과 각 접착제의 접착계면 관찰을 위하여 FE-SEM 관찰하였다. C-ABC 처리여부와 관계없이 습윤한 상아질면에 접착한 군은 모든 접착제에서 통계학적으로 유의성있는 미세인장결합강도의 차이를 나타나지 않았다(p > 0.05). C-ABC를 적용하였을 경우, Single Bond 2에서는 재수화한 상아질면에 접착한 군이 습윤한 상아질면에 접착한 군에 비해 미세인장결합강도가 감소하였다(p < 0.05). FE-SEM 관찰결과, C-ABC를 적용후에는 접착성 파괴가 주로 일어났으며, 교원질 섬유간 거리가 증가하였으며 부분적으로 교원질 섬유들간에 응집된 양상이 관찰되었다.