• 마이크로전자및패키징학회지
• /
• 제10권3호
• /
• pp.9-17
• /
• 2003

In this paper, thermo-mechanical and rheological properties of NCPs (Non-Conductive Pastes) depending on silica filler contents and diluent contents were investigated. And then, thermal cycling (T/C) reliability of flip chip assembly using selected NCPs was verified. As the silica filler content increased, thermo-mechanical properties of NCPs were changed. The higher the silica filler content was added, glass transition temperature ($T_g$) and storage modulus at room temperature became higher. While, coefficient of thermal expansion (CTE) decreased. On the other hand, rheological properties of NCPs were significantly affected by diluent content. As the diluent content increased, viscosity of NCP decreased and thixotropic index increased. However, the addition of diluent deteriorated thermo-mechanical properties such as modulus, CTE, and $T_g$. Based on these results, three candidates of NCPs with various silica filler and diluent contents were selected as adhesives for reliability test of flip chip assemblies. T/C reliability test was performed by measuring changes of NCP bump connection resistance. Results showed that flip chip assembly using NCP with lower CTE and higher modulus exhibited better T/C reliability behavior because of reduced shear strain in NCP adhesive layer.

• Restorative Dentistry and Endodontics
• /
• 제29권6호
• /
• pp.520-531
• /
• 2004

The aim of this study was to investigate the effect of monomer and filler compositions on the rheological properties related to the handling characteristics of resin composites. Methods. Resin matrices that Bis-GMA as base monomer was blended with TEGDMA as diluent at various ratio were mixed with the Barium glass (0.7 um and 1.0 um), 0.04 um fumed silica and 0.5 um round silica. All used fillers were silane treated. In order to vary the viscosity of experimental composites, the type and content of incorporated fillers were changed, Using a rheometer, a steady shear test and a dynamic oscillatory shear test were used to evaluate the viscosity ($\eta$) of resin matrix, and the storage shear modulus (G'), the loss shear modulus (G"), the loss tangent ($tan{\delta}$) and the complex viscosity (${\eta}^*$) ofthe composites as a function of frequency ${\omega}{\;}={\;}0.1-100{\;}rad/s$. To investigate the effect of temperature on the viscosity of composites, a temperature sweep test was also undertaken. Results. Resin matrices were Newtonian fluid regardless of diluent concentration and all experimental composites exhibited pseudoplastic behavior with increasing shear rate. The viscosity of composites was exponentially increased with increasing filler volume%. In the same filler volume, the smaller the fillers were used, the higher the viscosities were. The effect of filler size on the viscosity was increased with increasing filler content. Increasing filler content reduced $tan{\delta}$ by increasing the G' further than the G". The viscosity of composites was decreased exponentially with increasing temperature.

• 공업화학
• /
• 제26권4호
• /
• pp.452-457
• /
• 2015

네온변압기용 에폭시계 수지는 변압기로 완성되었을 경우 내열성 및 온도차 피로극복 등 열내구성이 우수하여야 한다. 따라서 본 연구에서는 에폭시계 수지에 보강제로 이산화규소를 첨가하고 증량제로 silica를 선정하여 입자크기별 혼합비에 따른 열전도도와 열안정성을 측정하였다. 혼합 silica의 최적 첨가량은 50 wt%이었으며, 혼합 silica 중 입자크기가 큰 규사의 첨가량이 증가함에 따라 열안정성이 우수하였다. 혼합 silica의 입자크기별 최적 혼합비는 (28/35 : 14/18 : 8/10 mesh = 1 : 1 : 1)이었으며, 이로부터 열내구성이 향상된 네온변압기를 제작할 수 있었다.

• 분석과학
• /
• 제20권6호
• /
• pp.488-495
• /
• 2007

본 연구에서는 headspace-solid phase microextraction(HS-SPME)-GC/MS법을 이용하여 PVC 벽지의 원자재에서 방출되는 TVOC를 분석하여 기여도를 평가하였다. 시료로 사용한 원자재는 6종으로 희석제, 안정제, 가소제, 충전제, 발포제와 PVC 레진이다. 각 원자재 시료를 22 mL 바이알에 9 mL씩 취한뒤 $100^{\circ}C$에서 1시간동안 평형을 이룬 다음 $75{\mu}m$ Carboxen-PDMS 화이버로 $25^{\circ}C$에서 1시간 흡착하여 GC/MS로 분석하였다. 정성결과 toluene, ethylbenzene 그리고 xylene과 같은 방향족 화합물과 acetone, methoxyacetone, 2-butanone 등의 케톤류와 nonane, decane, undecane 등의 알켄류가 검출되었다. 그 밖에도 ethanol, butanol 등의 알콜류와 알데히드류 등이 검출되었다. TVOC 방출량은 희석제 $54.20{\mu}g/g$, 안정제 $32.88{\mu}g/g$, 가소제 $0.50{\mu}g/g$, PVC 레진 $0.88{\mu}g/g$, 발포제 $0.22{\mu}g/g$, 충전제가 $0.11{\mu}g/g$로 나타났다. 각 원자재의 TVOC 방출량과 배합비를 고려한 TVOC 기여도는 희석제 0.708, 안정제 0.129, PVC 레진 0.115 순으로 높게 나타났다. 따라서 희석제와 안정제, PVC레진의 질적인 개선을 통해 TVOC 방출량을 줄이는 노력이 필요하다. 또한 본 연구에서 개발한 HS-SPME-GC/MS 방법은 원자재의 TVOC 분석에 유용하게 사용될 것으로 생각된다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권2호
• /
• pp.77-80
• /
• 2014

The effect of reactive diluents on the ac electrical treeing in epoxy/nanosilicate systems was studied, in a needle-plate electrode geometry. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and layered silicate was used as a nano-sized filler. Polyglycol (PG) or 1,4-butanediol diglycidyl ether (BDGE) was introduced as a reactive diluent to the DGEBA/nanosilicate system, in order to decrease the viscosity of the nanocomposite system. PG acted as a flexibilizer, and BDGE acted as a chain extender, after the curing reaction. To measure the treeing propagation rate, a constant alternating current (ac) of 10 kV/4.2 mm (60 Hz) was applied to the specimen, in a needle-plate electrode arrangement, at $30^{\circ}C$ of insulating oil bath. When 10 kV/4.2 mm (60 Hz) was applied, the treeing propagate rate in the DGEBA system was $1.10{\times}10^{-3}$ mm/min, and that in the DGEBA/PG system was $1.05{\times}10^{-3}$ mm/min. As 1.5 wt% of nanosilicate was added to the DGEGA/PG system, the propagation rate was $0.33{\times}10^{-3}$ mm/min. This meant that the nano-sized layered silicates would act as good barriers to treeing propagation. The effect of chlorine content was also studied, and it was found that chlorine had a bad effect on the electrical insulation property of the epoxy system.

• 대한치과보철학회지
• /
• 제41권5호
• /
• pp.606-616
• /
• 2003

Purpose : The purpose of this study was to research the properties of some chemically cured methacrylate polymers such as MMA, HEMA, TEG-DMA, bis-GMA, GMA. Material and Method : 5 kinds of methacrylates were selected and added 2% tertiary amine and benzoyl peroxide to make a chemically curable polymer 25 micron crushed silicas which are treated with silane were selected as filler, they were added into methacrylate monomer until the consistency did not changed by the load of 500gram. All of the experimental resins were 5 kinds, and a serial test was done with 3 kinds of items including the filler contents, the tensile strength, and the bond strength. The number of specimen were 10 for each group. Filler contents were obtained by reducing the specimens to ashes at $600^{\circ}C$ for 1 hour. The specimens with the dimension of 6mm in diameter and 3mm thick were immersed in $37{\pm}1^{\circ}C$ distilled water for 24 hours before test, and tensile strength were measured with cross-head speed 1mm/min. Shear bond strength were mea sured on the specimens attached to bovine enamel etched with 37% phosphoric acid for 1 minute. Results : 1. Maximum filler incorporation was the highest as 75.5% on MMA, and the least as 53.4% on bis- GMA(p<0.0001). 2. The tensile stregth were MMA 141.3, GMA 154.3, TEG-DMA 157.4, bis-GMA 161.4 MPa, and HEMA showed the highest value, 226.9MPa(p = 0.0004). 3. The bond strength were GMA 10.1, TEG-DMA 11.7, HEMA 12.2, bis-GMA 13.3 MPa, and MMA showed the highest value, 15.3MPa, however statistical significances were not (p =0.3838), 4. TEG-DMA and HEMA were not different on the aspect of maximum filler contents and shear bond strength(p>0.05). Conclusion : HEMA can be used as an another diluent substituting TEG-DMA with the increased strength and with the constant bond strength and the constant filler contents.

• 공업화학
• /
• 제29권2호
• /
• pp.201-208
• /
• 2018

올소-타입 불포화폴리에스테르 수지와 이소-타입 불포화폴리에스테르 수지를 합성하여 폴리머 모르타르 복합재료의 폴리머 결합재로 사용하였다. 불포화폴리에스테르 수지의 희석제로는 스티렌 모노머와 아크릴로니트릴을 사용하였고, 경화제로 methyl ethyl ketone peroxide (MEKPO), 가속제로 cobalt octoate (CoOc)를 사용하였다. 수지의 형태와 희석제의 종류에 따라 4종의 불포화폴리에스테르 수지를 제조하여 공시체 제조의 폴리머 결합재로 사용하였다. 폴리머 결합재의 첨가량에 따라 총 16종의 폴리머 모르타르 공시체를 제작하여 내열수성 시험을 행한 후 압축 및 휨강도시험, 세공분석 및 SEM 분석을 실시하였다. 시험결과, 이소-타입 불포화폴리에스테르 수지를 폴리머 결합재로 사용한 공시체가 올소-타입 불포화폴리에스테르 수지를 사용한 공시체보다 더 우수한 강도를 나타내었다. 내열수성시험 후에 측정한 총세공량과 세공의 평균직경은 시험 전에 측정한 값에 비하여 감소되었다. 내열수성시험 전에 관찰한 사진에서 폴리머 결합재와 충전재 및 잔골재가 co-matrix 상으로 견고하게 결합되어 있었으나 내열수성시험 후에 관찰한 사진에서는 폴리머 결합재가 대부분 분해되어 있는 것을 관찰할 수 있었다.

• 폴리머
• /
• 제28권5호
• /
• pp.426-432
• /
• 2004

상업적으로 이용되는 고분자계 치과용 수복재의 문제점인 중합시 나타나는 부피 수축을 감소시키기 위해 (2,2-비스[4-(2-하이드록시-3-메타크릴로일옥시프로폭시)페닐] 프로판) (bis-GMA), 유도체인 (2,2-비스[3-메틸, 4-(2-하이드록시-3-메타크릴로일옥시프로폭시)페닐] 프로판) (DMBis-GMA)와 (2,2-비스[3,5-디메틸, 4-(2-하이드록시-3-메타크릴로일옥시프로폭시)페닐] 프로판) (TMBis-GMA)를 합성하고 이를 희석제, 스파이로 오쏘카보네이트, 무기 충진재와 혼합하여 새로운 고분자계 치과용 수복재를 제조하였다. Bis-GMA 유도체/Bis-GMA 유도체/희석제 혼합계들 중에서 Bis-GMA/TMBis-GMA/TEGDMA 계의 중합 수축률이 가장 작았다. 이혼합계에 스파이로 오쏘카보네이트를 첨가함으로써 중합 수축률은 더욱 감소하였다. 최소의 중합 수축률을 나타내는 레진 단량체 혼합물을 사용하여 치과용 수복재를 제조한 결과 중합 수축률은 $0.7\%$로 기존 수복재의 중합 수축률 $2.5\%$에 비해 크게 감소하였다. 또 수복재의 기계적 강도는 기존 소재와 비슷하였지만 중합이 완료되는데 필요한 시간은 지연되었다.

• 대한치과보철학회지
• /
• 제41권4호
• /
• pp.476-492
• /
• 2003

Purpose : The purpose of this study was to compare HEMA and TEGDMA as diluents for the composite resin. Material and methods : Eight kinds of experimental light curable composite resins were prepared and used. Concentrations of monomer and filler were same for all experimental composites, except, the diluent's ratios to the monomer. The ratio of diluents to Bis-GMA were 15%, 20%, 25%, and 30%, and two kinds of diluents were used, so total experimental groups were eight including one control group of 25% TEGDMA. Results : Depth of cure, flexural strength, shear bond strength to bovine enamel, shear bond strength to bovine dentin, water absorption and solubility of composites in water were measured. Sample size for each groups were 10. Arithmetic means were used as each groups representative values, and regression test for two diluents and low concentrations, Duncan's multiple range test, and Two-way ANOVA test were done for kinds of diluents and its concentrations at level of 0.05. Conclusion : Following results were obtained ; 1. There were not significant differences in effects of HEMA and TEGDMA to depth of cure, flexural strength of composites and shear bond strength to bovine enamel (p>0.05). 2. Increase of the concentrations of the diluents made the depth of cure (p<0.001) and flexural strength (p<0.05) a little higher. 3. Shear bond strength to dentin was higher on HEMA containing composites than TEGDMA containing composites (p<0.001). 4. Water absorption was higher on HEMA containing composites than TEGDMA containing composites (p<0.01).

• Restorative Dentistry and Endodontics
• /
• 제33권1호
• /
• pp.1-8
• /
• 2008

본 연구는 공초점 현미경을 이용하여 새로운 단량체와 filler의 크기, 연마방법이 실험용 복합레진의 표면조도에 미치는 영향을 연구하였다. 단점이 많은 희석재인 TEGDMA의 사용을 줄이기 위해, Bis-GMA의 유도체로서 중합수축이 적고 점도가 낮은 새로운 단량체인 methoxlyated Bis-GMA (Bis-M-CMA)를 첨가하고 다른 크기의 filer를 갖는 2종의 실험용 복합레진과 TEGDMA를 함유한 1종의 실험용 복합레진을 제작하였다. EX1; 실험용 복합레진 1 (Bis-M-GMA/TEGDMA = 95/5 wt%, 40 nm 나노필러 함유), EX2; 실험용 복합레진 2 (Bis-M-GMA/TEGDMA = 95/5wt%, 20 nm 나노필러 함유), EX3; 실험용 복합레진 3 (Bis-GMA/TEGDMA = 70/30 wt%, 40 nm 나노필러 함유). 테프론 몰드를 이용하여 지름 6 mm 두께 2 mm의 시편을 각 실험용 복합레진과 Filtek Z250으로 9개씩 만들고 3군으로 분류하였다. Mylar strip 군은 연마를 하지 않았고, Sof-lex군은 #1000 SiC paper로 연마한 뒤 501-lex disc로 연마하였다. Diapolisher 군은 #1000 SiC paper로 연마한 뒤 DiaPolisher polishing point로 연마하였다. 공초점 현미경을 이용하여 각 시편당 7군데에서 Rq (Root mean square roughness), Rv (Valley roughness), Rp (Peak roughness), Rc (2D Roughness), Sc (3D Roughness) 값을 측정하였고, Two-way ANOVA와 Tukey multiple comparisons test로 유의수준 0.05로 통계처리 하였다. 복합레진의 종류 (p < 0.001), 연마 방법 (p < 0.001)은 각각 모두 표면조도 값에 영향을 미치며, 복합레진의 종류와 연마 방법 간에는 교호 작용이 관찰되었다 (p < 0.001). 복합레진의 종류에 따른 표면조도는 EX2가 가장 거친 표면을 보였고, EX3이 가장 평활한 면을 형성하였으며 (p < 0.05). 연마 방법에서는 연마하지 않은 Mylar strip 군이 가장 평활한 면을 형성하였다 (p < 0.05). 본 연구 결과를 종합하여보면 연마하지 않고 Mylar strip하에서 복합레진이 중합된 경우 가장 낮은 표면조도와 평활한 표면을 보였으며, 새로운 레진 단량체인 Bis-M-GMA를 함유한 복합레진이 수복물의 표면조도 측면에서는 필러 크기에 관계없이 기존의 Bis-GMA/TEGDMA를 기질단량체로 사용하는 복합레진에 비교하여 우수하지 못한 것을 확인하였다.