• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.11
• /
• pp.29-34
• /
• 1995

Mirror coating is applied to laser facets to improve properties of edge emitting laser diodes. In this experiment, InGaAsP/GaAs high power laser diodes were studied with respect to different degrees of anti-reflective coating. Sputterred $Al_{2}$O$_{3}$ was used as the coating material and the HR coating was kept constant at 90%. Threshold current density, differential quantum efficiency, emission wavelength and the operating current at 500mW were measured for a range of AR coating and compared with theoretically calculated values; that showed good agreements. Precise wavelength control is important for laser diodes for solid state pumping because of small absorption bandwidth. In addition, since these lasers operate under CW condition, a lowest possible operating current for a given power is desired in order to minimize the heat produced. From the results of this experiment, we were able to obtain a optimum range of AR coatings for minimum operating current. The wavelength can be varied up to 4nm within this range.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.469-472
• /
• 2004

In this paper a current mode sense amplifier suitable for 30nm SONOS flash memories read operation is presented. The proposed sense amplifier employs cross coupled latch type circuit and current mirror to amplify signal from selected memory cell. This sense amplifier provides fast response in low voltage and low current dissipation. Simulation results show the sensing delay time and current dissipation for power supply voltages Vdd to expose limitations of the sense amplifier in various operating conditions.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.5
• /
• pp.235-241
• /
• 2013

A low power CMOS control circuit is applied in an integrated DC-DC buck converter. The integrated converter is composed of a feedback control circuit and power block with 0.35 ${\mu}m$ CMOS process. A current-sensing circuit is integrated with the sense-FET method in the control circuit. In the current-sensing circuit, a current-mirror is used for a voltage follower in order to reduce power consumption with a smaller chip-size. The N-channel MOS acts as a switching device in the current-sensing circuit where the sensing FET is in parallel with the power MOSFET. The amplifier and comparator are designed to obtain a high gain and a fast transient time. The converter offers well-controlled output and accurately sensed inductor current. Simulation work shows that the current-sensing circuit is operated with an accuracy of higher than 90% and the transient time of the error amplifier is controlled within $75{\mu}sec$. The sensing current is in the range of a few hundred ${\mu}A$ at a frequency of 0.6~2 MHz and an input voltage of 3~5 V. The output voltage is obtained as expected with the ripple ratio within 1%.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.9
• /
• pp.129-134
• /
• 2016

This paper studies the high frequency PWM (pulse width modulation) driving technique to increase an optical efficiency and to prevent an optical color quenching of blue laser for head up display on vehicles using digital micro mirror device (DMD) panel and yellow phosphor wheel. The proposed approach adaptively drives the current pulse width modulated signals of high optical power of blue laser to increase the lifetime and to decrease the stem temperature of laser. This method stabilizes the temperature of laser according to the driving environment and the forward current capacity. By the proposed method, the brightness of blue laser is improved by about 37% compared to the continuous waveform current driving method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.10
• /
• pp.1477-1483
• /
• 2013

This paper proposes a low-voltage current-mode integrator for a continuous-time current-mode baseband channel selection filter. The low-voltage current-mode linear cascode integrator is introduced to offer advantages of high current gain and improved unity-gain frequency. The proposed current-mode integrator has fully differential input and output structure consisting of CMOS complementary circuit. Additional cascode transistors which are operated in linear region are inserted for bias to achieve the low-voltage feature. Frequency range is also controllable by selecting proper bias voltage. From simulation results, it can be noticed that the implemented integrator achieves design specification such as low-voltage operation, current gain, and unity gain frequency.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.861-863
• /
• 2005

The current-mode circuit technique to design a bi-directional current transceiver for remote control systems and telemetering systems is presented in this paper. The proposed transceiver can transmit and receive the industrial standard current signal 4-20mA at the same time using two wires connection. The realization method is based on a second generation current conveyor (CCII) and a current mirror, which can be implemented using a commercially available device. To demonstrate the performance of the proposed scheme, the transceiver was simulated by the use of the PSPICE analog simulation program. The simulation results verifying the circuit performance are agreed with the expected values. The crosstalk of the proposed transceiver of about .63dB is observed.

• Journal of KIISE:Software and Applications
• /
• v.31 no.11
• /
• pp.1543-1550
• /
• 2004

Modeling from images is a cost-effective means of obtaining 3D geometric models. These models can be effectively constructed from classical Structure from Motion algorithm. However, it's too difficult to reconstruct whole scenes using SFM method since general sites contain a very complex shapes and brilliant colours. To overcome this difficulty, the current paper proposes a new reconstruction method based on a moving Planar mirror. We devise the mirror posture instead of scene itself as a cue for reconstructing the geometry That implies that the geometric cues are inserted into the scene by compulsion. With this method, we can obtain the geometric details regardless of the scene complexity. For this purpose, we first capture image sequences through the moving mirror containing the interested scene, and then calibrate the camera through the mirror's posture. Since the calibration results are still inaccurate due to the detection error, the camera pose is revised using frame-correspondence of the comer points that are easily obtained using the initial camera posture. Finally, 3D information is computed from a set of calibrated image sequences. We validate our approach with a set of experiments on some complex objects.

• Journal of Magnetics
• /
• v.20 no.1
• /
• pp.52-56
• /
• 2015

The purpose of the current study was to investigate the effect of repetitive transcranial magnetic stimulation (rTMS) in conjunction with mirror therapy on the balance function of patients with sub-acute stroke hemiparesis. This study was conducted with 36 subjects who were diagnosed with a hemiparesis due to stroke. Participants in the experimental (19 members) and control groups (17 members) received rTMS and sham rTMS during 10 minute sessions each, which were carried out five days per week for four weeks. This was followed by the mirror therapy over 30 minute sessions, which were carried out five days per week for four weeks. Motor recovery was assessed by balance index, dynamic limits of stability, Berg balance scale, and time up go test. The change values of the balance index ($-2.06{\pm}1.99$ versus $-0.41{\pm}1.11$), dynamic limits of stability ($3.68{\pm}2.71$ versus $1.17{\pm}2.38$), and time up go test ($-7.05{\pm}5.64$ score versus $-3.35{\pm}5.30$ score) were significantly higher in the experimental group than in the control group (p < 0.05). At post-test, balance index ($4.08{\pm}1.14$ versus $5.09{\pm}1.04$), dynamic limits of stability ($13.75{\pm}0.60$ versus $11.73{\pm}3.53$), and time up go test ($23.89{\pm}4.51$ versus $28.82{\pm}3.07$) were significantly higher in the experimental group than in the control group (p < 0.05). In the experimental group, significant differences were found in the pre- and post-test scores for the balance index, dynamic limits of stability, Berg balance scale, and time up go test (p < 0.01). In the control group, a significant difference was observed between the pre- and post-test only for the Berg balance scale and time up go test (p < 0.05). These findings demonstrate that the application of 1Hz rTMS in conjunction with mirror therapy can be helpful in improving the balance function of patients with sub-acute stroke hemiparesis, and this may be used as a practical adjunct to routine rehabilitation therapy.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.4
• /
• pp.55-61
• /
• 1994

The multiple valued logic(MVL) circuit with ROM type using current mode CMOS is presented in this paper. This circuit is composed of the multiple valued-to-binary(MV/B) decoder and the selection circuit. The MV/B decoder decodes the single input multiple valued signal to N binary signal, and the selection circuits is composed N$\times$N array of the selecion cells with ROM types. The selection cell is realized with the current mirror circuits and the inhibit circuits. The presented circuit is suitable for designing the circuit of MVL functions with independent variables, and reduces the number of selection cells for designing the circuit of symmetric MVL functions as many as {($N^2$-N)/2}+N. This circuit possess features of simplicity. expansibility for array and regularity, modularity for the wire routing. Also, it is suitable for VLSI implementation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.42-50
• /
• 2003

This paper presents an embedded RC oscillator which has temperature compensation circuits. The conventional RC oscillator has frequency deviation about 15%, which is caused by variation of resistors and the reference voltage of schmitt trigger from the temperature condition. In this paper, the proposed circuit use a CMOS bandgap reference having balanced current temperature coefficients as a triggering voltage of schmitt trigger. The constant current sources consist of current mirror circuit with the positive and negative temperature coefficient. The proposed circuit shows less 3% frequency deviation for variation of temperature, supply voltage and process parameters.